Philips Pure Taste WP3861 User manual

Register your product and get support at
www.philips.com/welcome
WP3861

1

WP3861 Philips PureTaste
ENGLISH 6
繁體中文 17
简体中文 26

6
Introduction
Congratulations on your purchase and welcome to Philips!
To fully benet from the support that Philips offers,
register your product at www.philips.com/welcome.
You have made an excellent choice.The Philips Pure Taste is a compact and
easy-to-install water purier that improves the taste of your drinking and
cooking water by removing chlorine and other impurities with a silver-
coated activated carbon lter. Better-tasting water made easy, by Philips.
General description (Fig. 1)
ANon-woven cloth
BSilver-coated granular activated carbon
CFilter cartridge
D Cap of lter cartridge holder
EViewing window
FFilter cartridge holder
GWater selection lever
H Water purier housing
IStainless steel screen
JRubber washer
KAdapter
1A-type
2 B-type
3C type
4D-type
LAttachment nut
Important
Read this user manual carefully before you use the water purier and
save it for future reference.
Warning
- This water purier is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given
ENGLISH

supervision or instruction concerning use of the water purier by a
person responsible for their safety.
- Children should be supervised to ensure that they do not play with
the water purier.
Before daily use
- To prevent quick clogging of the lter cartridge, let the water run at
the unltered setting for around 5 seconds before every use.
- If the water is highly coloured or turbid due to work on your water
network, do not let the water run at the ltered setting until the
water is clear.
- Cautions:
1 Let the water run at the ltered setting for 10 seconds before use
each day.
2 Let the water run at the ltered setting for 60 seconds before use if
you have not used the water purier for more than two days.
3 If you are not going to use the water purier for more than two
weeks, put the lter cartridge in the refrigerator to ensure its good
performance. When you start using the water purier again, let
the water run at the ltered setting for 1 minute before use. If the
lter cartridge emits an unpleasant smell, replace it with a new one.
Water temperature
- Do not let water hotter than 50°C run through the water purier at
the unltered setting or hotter than 35°C at the ltered setting.
This may damage the water purier.
- Do not let the water purier freeze.
Applications
- Only use the water purier to lter water that meets drinking water
standards.
- Do not use this water purier in combination with electric taps.
- Do not block the ltered water outlet or connect other devices to it.
- If the water pressure is very high, reduce the water ow of the tap to
prevent damage to the cartridge.
ENGLISH 7

- Keep the water purier away from heat to avoid distortion or
breakage.
- Do not tamper with the water purier.
- Do not remove the lter cartridge while you use the water purier.
- Do not install the water purier near a window where it is exposed
to direct sunlight.
- Do not use the water purier without a lter cartridge.
- This water purier does not soften water.
- Do not use ltered water in aquariums. Tap water, ltered or
unltered, can be harmful to sh.
- This water purier is intended for household use only.
- Do not store puried water to avoid contamination. Air contact
contaminates puried water quickly. If you want to store puried
water, use a clean container and keep it in the refrigerator. Do not
keep it in the refrigerator longer than 1 day to avoid contamination.
Features
- The water purier removes chlorine, unpleasant smells and tastes, as
well as large sediments from your tap water.
- The silver-coated activated carbon prevents bacteria growth inside
the lter.
- The replacement reminder sticker helps you remember when to
replace the lter cartridge.
- The 2ltrs/min high-speed initial ow rate gives you plenty of clean
water instantly.
- The water selection lever offers you a choice of three water ow
types: unltered spray, unltered stream or ltered spray.
- The eight tap-mounting adapters supplied with the water purier
allow easy installation on almost any type of tap.
- The bayonet-type mount ensures quick, easy and secure lter
cartridge replacement.
ENGLISH8

Preparing for use
Before installation
- Before you install the water purier, make sure all tap-mounting
adapters you require are present.
- The tap must have a diameter of 13mm-25mm.
- Determine what type of tap you have and select the appropriate
adapter.
- The adapters supplied make the water purier suitable for almost
any kitchen tap. However, the water purier may not t some
uncommon types of taps.
- The tap water pressure has to be between 0.7kgf/cm² (7 metres of
water column/70kPa) and 3.5kgf/cm² (35 metres of water column/
350kPa). If you use the water purier at a water pressure outside this
range, either the ltered water ow will be extremely low or the
water purier will get damaged.
Installation A-type adapter
- For taps with a round spout with a diameter of 16mm, 17.5mm or
19mm (Fig. 2).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 3).
2 Pass the attachment nut over the tap spout (Fig. 4).
3 Place the matching adapter (A-type) over the tip of the spout. The
16mm adapter is packed with the water purier. Replace it with
the 17.5mm adapter or 19mm adapter to t the diameter of your
tap (Fig. 5).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 6).
Installation B-type adapter
- For taps with an aerator (threaded outside) (Fig. 7).
1 Remove the attachment nut and the adapter from the water
purier (Fig. 8).
ENGLISH 9

2 Remove the aerator cap from the tap and pass the attachment nut
over the spout. Take out the original adapter and screw the
matching adapter (B-type) onto the tap (Fig. 9).
3 Tighten the adapter further with a coin (Fig. 10).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 11).
Installation C-type adapter
- For taps with an aerator (threaded inside) (Fig. 12).
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 13).
2 Remove the aerator cap from the tap. Take out the original adapter
and screw the matching adapter (C-type) onto the tap through the
attachment nut. (Fig. 14)
If water leakage occurs, wind Teon tape round the adapter’s thread
before you screw it onto the tap.
3 Tighten the adapter further with a coin (Fig. 15).
4 Firmly screw the attachment nut onto the water purier
housing (Fig. 16).
Installation D-type adapter
- For taps other than A, B or C. (Fig. 17)
1 Remove the attachment nut and the adapter from the water
purier housing (Fig. 18).
2 Take out the original adapter and screw the D-type adapter loosely
onto the water purier housing. (Fig. 19)
3 Push the water purier housing onto the tap from below and
tighten the 4 screws evenly (Fig. 20).
4 Screw the attachment nut rmly onto the water purier
housing (Fig. 21).
Make sure the rubber washer is rmly pushed against the tap to prevent
water leakage.
ENGLISH10