Phonak iCube II User manual

User Guide
iCube II

2
1. Welcome 4
2. Description 5
3. iCube II accessories (optional) 6
4. Getting started 7
4.1 Setting up the power supply 7
4.2 Charging the battery 8
4.3 Operating time 10
4.4 Switching iCube II On and O 10
4.5 Target tting software requirements 10
5. Connecting iCube II to your computer 11
5.1 Connecting wirelessly 11
5.2 Connecting via USB cable 13
Contents

3
6. Using iCube II 14
6.1 Wearing iCube II 14
6.2 Detecting and programming
hearing instruments 15
6.3 Programming hearing instruments
on your desk 16
7. Indicator lights 17
8. Troubleshooting 20
9. Service and warranty 22
9.1 Local warranty 22
9.2 International warranty 22
9.3 Warranty limitation 22
10. Compliance information 23
11. Information and description of symbols 28
12. Important safety information 32

4
iCube II is designed specically for use by the hearing
care professional.
Please read this user guide carefully to benet from all
the features of the iCube II.
For further information, please visit the Phonak website
www.phonak-us.com
Phonak – life is on www.phonak-us.com
1. Welcome
CE mark applied: 2014

5
The intended use of this device is the wireless transfer
of tting data from the PC to the client’s hearing
instruments.
Wireless iCube II USB adapter
2. Description
On/O
Pairing
button
Neckloop plugs
Rear neckloop
opening
Mini USB
charging input
Right indicator
light (data
transfer)
Middle indicator
light (battery
state and PC data
transfer)
Left indicator
light (data
transfer)

6
3. iCube II accessories (optional)
JUSB cable, 3 m (10 ft)
JiCube II desktop stand
JUSB hub
Contents may vary depending on country.

1.
1. 2.
2.
7
4. Getting started
4.1 Setting up the power supply
Select the adapter for your country.
US EU
1. Insert the top round end of the
adapter into the round corner
of the power supply.
2. Click the tail of the adapter in
to lock it into place.
1. To remove, pull back the tab on
the power supply.
2. Pull the adapter upwards to
remove it.

8
4.2 Charging the battery
Plug a mini-USB plug into the
iCube II and plug the power
supply into a power outlet.
If you use the iCube II desktop stand,
install it as shown below.
It is recommended to charge iCube II whenever it is
not in use. This way it will be sufficiently charged and
ready for the next fitting session.
4. Getting started

9
iCube II desktop stand is available as an option
Battery notes
When charging iCube II for the rst time, leave it
to charge for at least three hours (even if the middle
indicator light changes to green color earlier).
Charging a depleted battery will take approx. 2 hours.
It is safe to leave iCube II connected for longer
periods, even if not in use.
A new battery’s full performance is achieved only
after three complete charge and discharge cycles.
The iCube II battery can be charged several hundred
times. If the operating time of your iCube II reduces
substantially, please contact your local Phonak
representative.

10
4. Getting started
4.3 Operating time
Fully charged, your iCube II will operate for up to twelve
hours of continuous tting.
4.4 Switching iCube II on and o
Slide the switch as
shown to switch iCube II
on or o.
Once iCube II is fully operational, the middle
indicator light will blink slowly.
Switch iCube II o when not in use and while
charging. The middle indicator light will stop
blinking.
4.5 Target tting software requirements
Before using iCube II, ensure that Phonak Target™ 4.0
or a later version is installed on the tting PC.
O On