Pichler PICHLER BERGFALKE 3000 User manual

R/C Modellflugzeug in Holz-Fertigbauweise
3000
Sonderzubehör:
# C5398, Elektrische Störklappen
# C7089, Antriebssatz Brushless für Bergfalke 3000
# C4995, Servo DS3012
# C4994, Servo DS4020
Optional Accessories:
# C5398, Electric Spoilers (flaps)
# C7089, Power Set Brushless for Bergfalke 3000
# C4995, Servo DS3012
# C4994, Servo DS4020

Bergfalke
2
Test fit the ailerons to the wing with the hinges. If the
hinges don’t remain centered, stick a pin through the
middle of the hinge to hold it in position.
Temporary pin to
keep hinge centered.
Assemble then apply drops of thin
C/A to center of hinge,on both sides.
2x10mm
4x30mm
3x12mm
A
B1
C
D
B2
Rudder
E
E. Aluminium tube wing dihedral brace.

33
Install the rubber grommets and brass eyelets on to the
aileron servos.
Using a modeling knife, remove the covering from over
the pre-cut servo arm exit hole on the aileron servo tray
/hatch.This hole will allow the servo arm to pass
through when installing the aileron pushrods.
Using the thread as a guide and using masking tape,
tape the servo lead to the end of the thread: carefully
pull the thread out. When you have pulled the servo
lead out, remove the masking tape and the servo lead
from the thread.
Befestigen
Secure
Drill a hole 1.5 mm
1.5 mm
Place the servo into the servo tray. Center the servo
within the tray and drill 1.5mm pilot holes through the
block of wood for each of the four mounting screws
provided with the servo.
Electric wire
Drill a hole 1.5 mm
1.5 mm
2x10mm
Befestigen
Secure
Remove the covering from the slot on the bottom of the
aileron.
Insert the control horn into the slot and secure it by A+B
Epoxy glue.
1. A/B glue
5-Min. Epoxy Klebstoff
Epoxy
2. Push in
control horn
Aileron
Aileron Control Horn
Bergfalke

Installing the aileron linkages
Installing the aileron linkages as pictures below.
100mm
Snap keeper.
M2 lock nut
Flaslink
Pushrod wire Control horn
Bend and cut.
Silicone Tube
Bergfalke
Using pliers, carefully make a 90 degree bend down
at the mark made. Cut off the excess wire, leaving
about 6mm beyond the blend.
Insert the 90 degree bend down through the hole in
the control horn. Install one nylon snap keeper over
the wire to secure it to the control horn. Install the
control horn retaining screw and remove the from the
aileron.
Repeat the procedure to install the second aileron
linkages in the opposite wing half.
After both linkages are completed. connect both of
the aileron servo loads using a Y-harness you have
purchased.
Installing Electric Spoilers.
Installing the as pictures below.Electric Spoilers
Repeat the procedure to install the second
in the opposite wing half.
Electric
Spoilers
Motoreinbau / Motor Installation
4
Not included

Bergfalke
Installing the fuselage servos
1. Install the rubber grommets and brass collets
into the elevator, rudder. Test fit the servos into the
servo tray. Trim the tray if necessary to fit your
servos.
2. Mount the servo to the tray using the mounting
screws provided with your radio system.
Rudder servo
Elevator servo
Rudder install as same as the way of aileron.
Please see pictures below:
5
150mm
Ball bearing
Rudder control horn and linkage install as same as
the way of aileron. Please see pictures below:
2. Push in
1. A+B Epoxy glue
Control horn
(not included)
nicht enthalten
Power Set for Bergfalke
available seperately
# C7089
Antriebsset Bergfalke
separat erhältlich

Bergfalke
Using pliers, carefully make a 90 degree bend down
at the mark made. Cut off the excess wire, leaving
about 6mm beyond the blend.
Insert the 90 degree bend down through the hole in
the servo arm. Install one nylon snap keeper over the
wire to secure it to the servo arm.
Rudder servo
Rudder pushrod
Bend
and cut.
Snap keeper
Flaslink
Pushrod wire Servo arm
1) Elevator install as same as the way of aileron.
2) Draw a center line onto the horizontal stabilizer.
Then put the horizontal into the fuselage.
With the horizontal stabilizer correctly aligned, Screw
the elevator in position.
Secure
3) Check the fit of the horizontal stabilizer in its slot.
Make sure the horizontal stabilizer is square and
centered to the fuselage by taking measurements, but
don’t glue anything yet.
Elevator and Main wing must be aligned parallel
to each other
6

Bergfalke
Repeat the procedure to install the second e
.
levator
control horn and linkage
Elevator control horn and install as same as the
way of aileron. Please see pictures below.
linkage
Befestigen
Secure
Befestigen
Secure
Akku Battery
505mm
Aluminium tube. 12mm.
Receiver
Regler ESC
Installing The Receiver, ESC And Battery
Locate the aluminium wing dihedral brace.
Servo arm
Elevator pushrod
Cut. Secure
Snap keeper.
Using pliers, carefully make a 90 degree bend down
at the mark made. Cut off the excess wire, leaving
about 6mm beyond the blend.
Insert the 90 degree bend down through the hole in
the servo arm. Install one nylon snap keeper over the
wire to secure it to the servo arm.
7
3x12mm
Battery tray

Bergfalke
A/B Epoxy glue
Attach the aluminium tube into the fuselage.
Push in
Push in
Push in
Screw the wing panel in position.
Push in
8
Secure
Secure
Push in
Magnet

50mm
50mm
Bergfalke
Rudder control
25mm
15mm
25mm
25mm
50mm
50mm
50mm
Position the canopy so the rear frame on the canopy is
aligned with the rear edge of the cockpit opening. Use
canopy glue to secure the canopy to the canopy hatch.
Use low-tack tape to hold the canopy in position until
the glue fully cures. Wrap the tape completely around
the canopy hatch, as the tape does not stick well to the
covering. We used balsa sticks to hold the lower edges
of the canopy tightly against the canopy hatch.Installing
the fuselage hatch as same as picture below.
9
Aileron: 25mm up 15mm down
Elevator: 25mm up 25mm down (30%Expo)
Rudder: 50mm right 50mm left
© Copyright PICHLER Modellbau
www.pichler-modellbau.de