Pickering 40-566B User manual

pickeringtest.com
Issue 1.1 August 2023
40-566B User Manual
PXI 2 A BRIC™ Multi-Slot Matrix Module

Page (II) 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Page (II) REED RELAY MODULE 40-110/115/120/125
pickering
© COPYRIGHT (2023) PICKERING INTERFACES. ALL RIGHTS RESERVED.
No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by
any means without the written permission of Pickering Interfaces.
Technical details contained within this publication are subject to change without notice.
ISO 9001
Reg No. FM38792

Page (III)
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Page (III)
REED RELAY MODULE 40-110/115/120/125
pickering
TECHNICAL SUPPORT
For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.
WARRANTY
All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of
three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be
defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.
Products serviced and repaired outside of the warranty period are warranted for ninety days.
Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.
ENVIRONMENTAL POLICY
Pickering Interfaces operates under an environmental management system similar to ISO 14001.
Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the
environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and
safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can
be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.
Worldwide Technical Support and Product Information
pickeringtest.com
Germany
Tel: [phone]
E-mail: [email protected]
Sweden
Tel: [phone]
E-mail: [email protected]
USA
Tel: (West) [phone]
Tel: (East) [phone]
E-mail: [email protected]
Czech Republic
Tel: [phone]
E-mail: [email protected]
France
Tel [phone]
E-mail [email protected]
Pickering Interfaces Headquarters
Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom
Tel: [phone]
E-Mail: [email protected]
China
Tel: [phone]
E-mail: [email protected]

Page (IV) 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Page (IV) REED RELAY MODULE 40-110/115/120/125
pickering
MEANING / DESCRIPTION SYMBOL
PROTECTIVE EARTH (GROUND)
To identify any terminal which is intended for connection to an external conductor for
protection against electric shock in case of a fault, or the terminal of a protective earth
(ground) electrode.
DANGEROUS VOLTAGE
To indicate hazards arising from dangerous voltages.
WARNING / CAUTION
An appropriate safety instruction should be followed or caution to a potential hazard
exists.
Refer to the relevant instructions detailed within the product manual.
HEAVY
If this product is heavy reference should be made to the safety instructions for
provisions of lifting and moving.
STATIC SENSITIVE
To indicate that static sensitive devices are present and handling precautions should
be followed.
!
kg
SAFETY SYMBOLS
PRODUCT SAFETY
The following safety symbols may be used on the product and throughout the product documentation.

Page (V)
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Copyright Statement ...................................................................II
Technical Support and Warranty................................................III
Product Safety .............................................................................IV
Contents (this page)....................................................................V
Warnings and Cautions ..............................................................VII
Section 1
Technical Specication...............................................................1.1
Section 2
Technical Description .................................................................2.1
Mechanical Description ........................................................2.1
Functional Description .........................................................2.1
Section 3
Installation....................................................................................3.1
Pre Operation Checks...........................................................3.1
Hardware Installation ............................................................3.2
Software Installation .............................................................3.2
Testing Operation ..................................................................3.3
Section 4
Programming Guide....................................................................4.1
Programming Options for Pickering PXI Modules .............4.1
Module Architecture..............................................................4.2
Programming The Module ....................................................4.2
Section 5
Connector Information................................................................5.1
Section 6
Trouble Shooting.........................................................................6.1
Section 7
Maintenance Information............................................................7.1
Switching System Test Tools ...............................................7.1
Fuse Replacement.................................................................7.1
Relay Look-Up Tables ...........................................................7.3
PCB Layout Diagrams...........................................................7.11
Retting the Sub-Matrix Cards.............................................7.12
CONTENTS

Page (VI) 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
THIS PAGE INTENTIONALLY BLANK

Page (VII)
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Page (VII)
2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
WARNINGS AND CAUTIONS
WARNING - HAZARDOUS ENVIRONMENTS SYMBOL
This product is not specically designed for use in hazardous environments, for example in explosive
atmospheres. If the product is to be used in hazardous environments we recommend that the user
ensures suitable protective measures are taken.
!
WARNING - DANGER OF ELECTRIC SHOCK SYMBOL
This module may contain hazardous voltages. Before removing the module from the rack remove all
supplies and disconnect user I/O signals.
Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O
signals that may be present. Blanking panels are available to order from Pickering in a variety of
slot widths. If the product is not used in this manner for example by using an extender card then
additional care must be taken to avoid contact with exposed signals.
Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.
This module must not be used for the switching of Mains Circuits. For the switching of voltages up
to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must
be fully isolated from the Mains Circuit and the safety earth.
The host chassis must be correctly installed and be connected to mains or factory safety ground,
please refer to your chassis installation manual.
Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT
For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage
Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved
by a transformer in which the primary windings are separated from the secondary windings by
reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.
CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL
Certain semiconductor devices used in this equipment are liable to damage due to static voltage.
Observe the following precautions when handling these devices in their unterminated state, or
sub-assemblies containing these devices:
1. Persons removing sub-assemblies from equipment using these devices must be earthed by a
wrist strap and a resistor at the point provided on the equipment.
2. Soldering irons used during the repair operations must be low voltage types with earthed tips and
isolated from the mains voltage by a double insulated transformer.
3. Outer clothing worn must be unable to generate static charges.
4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in
anti-static bags.
PXI Switching
Module
Device
Under Test
Power
Supply
Power
Supply
Host Chassis
Secondary Circuit
Mains
Circuit
Mains
Circuit
Mains/Factory
Safety Ground

Page (VIII) 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579
pickering
CAUTION - PRODUCT DOCUMENTATION SYMBOL
Suitably qualied & trained users should ensure that the accompanying documentation is fully read
and understood before attempting to install or operate the product.
!
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O
signals (refer to the Maintenance Section).
• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or
the combined weight of the modules & chassis.
• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the
chassis and the user I/O signals.
• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.
• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on
the front of the unit.

Page 1.1
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
SECTION 1 - TECHNICAL SPECIFICATION
High Reliability and Easy of Use
The 40-566B PXI BRIC is designed to minimise the cost and
complexity of cable assemblies to the device under test and
instrumentation. Analog busing is housed within the module
using a high performance screened analog backplane.
Pickering can construct custom cable assemblies for all of our
PXI modules, please contact sales office for further assistance.
yIntegrated PXI 2 A Matrix Module With Built In
High Performance Screened Analog Bus
yFully Scalable Matrix Solution
yHigh Density Configurations With 4-Slot to
165x4 (2-Pole) & 8-Slot to 385x4 (2-Pole)
yFlexible Matrix Architecture Through Isolation
Switching Enabling Multiple Independent
Matrices (Up To 7 Per BRIC8)
yPartially Populated Versions Available
yMaximum Current 2 A Hot or Cold Switching
y2-Pole Switching up to 300VDC/250VAC
and up to 60W Max Power
yDrivers Supplied for Windows & Linux, Plus
Support for Real-time Systems
ySupported by PXI or LXI Chassis
ySupported by BIRST ™ and eBIRST ™ Test Tools
y3 Year Warranty
Built-In Relay Self-Test -
BIRST
This provides a quick and simple way of finding relay failures.
No test equipment is required, simply disconnect the UUT,
launch the BIRST application and the tool will run a diagnostic
test that will find all relays with faulty contacts.
For more information go to: pickeringtest.com/birst
Supported by eBIRST
eBIRST test tools simplify switching fault-finding by quickly
testing the system and graphically identifying the faulty relay.
For more information go to: pickeringtest.com/ebirst
BRIC ™ 2nd Generation PXI 2 A Switch Matrix
The 40-566B BRIC provides a range of high density matrix
configurations able to switch up to 2 A or 300 VDC/250 VAC.
The modules are available in 4 or 8-slot PXI sizes and are
constructed using high quality electro-mechanical relays.
Typical applications include signal routing for functional
ATE systems. With this high level of switching density, the
40-566B allows a complete functional ATE switching system
to be housed in a single 3U PXI chassis. BRIC Modules allow
the use of a much lower cost 8 slot PXI chassis.
• BRIC4 - 4-slot PXI Module, this can hold up to 3 matrix
daughtercards, 660 crosspoints (up to 165x4, 2-pole).
• BRIC8 - 8-slot PXI Module, this can hold up to 7 matrix
daughtercards, 1824 crosspoints (up to 385x4, 2-pole).
Pickering 2 A BRIC matrices are higher signal power versions
of our established range of PXI BRIC modules. Comprising
high quality electro-mechanical relays they feature higher
voltage, current and power handling than ultra high density
reed relay based BRICs.
The 40-566B is an ideal choice for simultaneously busing up
to four higher power signal pairs, where improved robustness
is required (please refer to our 40-573 for busing up to eight
higher power signal pairs simultaneously).
For lower level switching requirements, please consider our
40-560B/561A/562B range of ruthenium reed relay solutions
that exhibit superior operating speed & life performance.
pickeringtest.com
40-566B
PXI 2-Pole 2 A BRIC™ Multi-Slot Matrix
Issue 1.1 August 2023

Page 1.2 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
40-566B BRIC Key Advantages
• Complete PXI Switching Solution in one PXI Module.
• Simplified cabling, easy to connect to the DUT thus minimizing costs.
• Internal Shielded Analog Bus giving maximum signal integrity with easy expansion at minimal
cost with maximum bandwidth and isolation.
• Program as one whole matrix, therefore very easy to achieve fast operate time.
• Targeted at high performance matrix switching with minimized cost.
• Build just the matrix configuration you need. Modular architecture allows users to buy just as
much matrix capacity as they require, extra cards can be added later to expand the matrix.
• BRICs allow use of much lower cost 8 slot PXI chassis (40-908).
• Simpler and faster programming with Direct I/O, VISA and IVI Drivers + LabVIEW Soft Front
Panels. Fully compatible with NI Switch Executive.
• Custom versions built to order.
• Built-In Relay Self Test (BIRST & eBIRST).
Pickering’s Range of 2 A BRIC Matrix Modules
Model No. Poles Y-Bus Size Min. Matrix Size Max. Matrix Size
40-568A 1 4 75x4 600x4
40-596A 1 6 58x6 464x6
40-567A 1 8 44x8 352x8
40-597 1 12 32x12 256x12
40-598 1 16 24x16 192x16
40-566B 2 4 55x4 385x4
40-574 2 4 (dual analog bus) 57x4 456x4
40-565A 2 8 24x8 192x8
40-573 2 8 29x8 232x8
X1 X55
X165
Y1
Y2
Y3
Y4
X1
Matrix
Crosspoint
X1 X55
X385
Y1
Y2
Y3
Y4
X1
Matrix
Crosspoint
The 40-566B in BRIC4 Format is Available With Matrix
Configurations Between 55x4 and 165x4 (2-Pole)
The 40-566B in BRIC8 Format is Available With Matrix
Configurations Between 55x4 and 385x4 (2-Pole)
40-566B
pickeringtest.com Page 2
PXI 2-Pole 2 A BRIC™ Multi-Slot Matrix

Page 1.3
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
Flexible Matrix Architecture
Isolation Switching within the 40-566B enables the configuration of multiple independent matrices (up to 7 per BRIC8). These
switches allow the removal of redundant rows/columns within a system, maintaining signal integrity through maximized
bandwidth as well as keeping interconnection capacitance, leakage and crosstalk to a minimum.
Analog Backplane
The BIRST System
requires the front panel
adapter 44-566A-BAT4 to
check isolation relays for
independent sub-matrix Y
connection (no adapter
required to check all
other relays), please
contact sales office for
further information.
Y1 Y4
X1 X55
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Daughter Card 1
Y1 Y4
X56 X110
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 2
Y1 Y4
X111 X165
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 3
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
Y1 Y4
Front Panel 25-pin
D-Type Connector
Isolation
Switches
Switching Architecture of a 165x4 Matrix in BRIC4 Format (40-566B-004) Note: All Connections are 2-Pole
Example Configurations of the 40-566B 2 A BRIC Matrix (All connections via X-axis for maximum efficiency)
Schematic diagram showing a 385x4 BRIC Matrix being used to parallel test multiple DUTs.
The BRIC Matrix allows tremendous test system flexibility.
Instrument 1 Instrument 2 Instrument 3
1 2 3 4 5 6 7 8 9 10 11 12
Instrument 4 Instrument 5
20 21 22 23 24 25 26 27 28 29 30 31 32
Device Under Test No. 1
33 34 35 36 37 38 39 40 41 42 43 44 45
Device Under Test No. 2
46 47 48 49 383 384 385
Device Under Test No. 3
MATRIX
CROSSPOINT
40-566B
pickeringtest.com Page 3
PXI 2-Pole 2 A BRIC™ Multi-Slot Matrix

Page 1.4 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
Switching Architecture of a 385x4 Matrix in BRIC8 Format (40-566B-108) Note: All Connections are 2-Pole
Analog Backplane
The BIRST System
requires the front panel
adapter 44-566A-BAT4 to
check isolation relays for
independent sub-matrix Y
connection (no adapter
required to check all
other relays), please
contact sales office for
further information.
Y1 Y4
X1 X55
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Daughter Card 1
Y1 Y4
X56 X110
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 2
Y1 Y4
X111 X165
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 3
Y1 Y4
X331 X385
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 7
Y1 Y4
X166 X220
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 4
Y1 Y4
X221 X275
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 5
Y1 Y4
X276 X330
Front Panel 160-pin DIN41612 Connector
Isolation
Switches
Isolation
Switches
Daughter Card 6
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
MATRIX
CROSSPOINT
Y1 Y4
Front Panel 25-pin
D-Type Connector
Isolation
Switches
40-566B
pickeringtest.com Page 4
PXI 2-Pole 2 A BRIC™ Multi-Slot Matrix

Page 1.5
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
BUILT IN RELAY SELF TEST - BIRST
Compare Result
Measure Resistance
Last Group?
End
Output Relay
Number
Measure & Compare
Open Relay Group #n
Measure & Compare
Close Relay Group #n
Measure & Compare
Default Relay State
Start Self Test
Fail
Pass
Alter Group #n+1
No
Yes
Measure &
Compare
BIRST™ Flow Chart
Test Sequencer Front Panel for BIRST™. This allows any
combination of tests to be run in either single or multiple
sequences. All test data is displayed in the results window
and can be written to a data file.
It can be hard to confirm or identify faulty relays on complex
switching matrices. The user may be aware that the test
system is not behaving as expected but may be unsure if
it is a cabling fault, a software problem or a faulty matrix.
Discovering the source of the problem takes time and effort
users may not have when working to tight schedules.
To ensure low cost of ownership, Pickering Interfaces has now
incorporated a test tool, BIRST, into the BRIC.
BIRST
The BIRST is a sophisticated diagnostic tool, which allows a
complete relay self test of a BRIC module. The BIRST is an
easy to use, tool that is especially useful in remote production
sites where local technical support may be limited. It provides
the following features and capabilities:
• Complete BRIC, Matrix self-test capability
• High fault coverage, self-test tool
• Tests for all relay fault types (bad open or bad close)
• Identifies faults to individual component relay level
• Test sequencer allows detailed control of testing
• Test results shown on screen or sent to log file
• Runs single or repeat tests for maximum confidence Designed for Reliability and Serviceability
The BIRST provides a quick and cost effective way of
identifying the fault or simply providing reassurance that the
matrix is working correctly.
The design of Pickering Interfaces’ products ensures that relay
replacement is with a minimum of investment in tools. The use
of leaded relays in preference to surface mount ensures that
the replacement of one device will not stress others through
the use of re-flow techniques. Individual relay failures can be
corrected with little impact on the others in the matrix. This
maximizes the service life of the matrix even after a failure
has occurred and been repaired.
The repairer’s skills required are good understanding of
the extraction and replacement of leaded components.
Spare relays are included with many of Pickering’s lower
density matrix modules. Alternatively replacement parts are
readily available from Pickering Interfaces representatives.
The ability to replace failures locally ensures that system
downtime is minimized and transportation costs are avoided.
Built-In Relay Self-Test ( BIRST ) - Overview
40-566B
pickeringtest.com Page 5
PXI 2-Pole 2 A BRIC™ Multi-Slot Matrix

Page 1.6 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
Operating/Storage Conditions
Operating Temperature:
Humidity:
Altitude:
0 °C to +55 °C
Up to 90 % non-condensing
5000 m
Storage Temperature:
Humidity:
Altitude:
-20 °C to +75 °C
Up to 90 % non-condensing
15000 m
PXI & CompactPCI Compliance
The module is compliant with the PXI Specification 2.2. Local
Bus, Trigger Bus and Star Trigger are not implemented.
Uses a 33 MHz 32-bit backplane interface.
Safety & CE Compliance
All modules are fully CE compliant and meet applicable EU
directives:
Low-voltage safety EN61010-1:2010,
EMC Immunity EN61326-1:2013,
Emissions EN55011:2009+A1:2010.
RF Specification - In a 50 Ω System
Bandwidth (-3 dB): 10 MHz
Crosstalk (typical): 10 kHz:
100 kHz:
1 MHz:
10 MHz:
-65 dB
-60 dB
-35 dB
-15 dB
Isolation (typical): 10 kHz:
100 kHz:
1 MHz:
10 MHz:
65 dB
60 dB
45 dB
30 dB
Width and Dimensions
Four or eight slot 3U PXI module (CompactPCI).
3D models for these modules in a variety of popular file
formats are available on request.
Module Weight
Empty BRIC Fully Loaded BRIC
BRIC4 0.9Kg 2.1Kg
BRIC8 1.6Kg 4.0Kg
BRIC daughter card 0.32Kg
Connectors
PXI bus via 32-bit P1/J1 backplane connector.
X connections are made via multiple front panel 160-pin male
DIN 41612 connectors (Up to 3 per 4-slot module or up to 7
per 8 slot module).
Y connections are made via a single front panel 25-pin male
D-type connector.
Note: We recommend that Pickering mating connectors are
used with this module which are designed to ensure there
are no mechanical interference problems when used in a PXI
chassis.
Switching Specification
Switch Type: Electro-mechanical
Contact Type: Palladium-Ruthenium,
Gold Covered
Bifurcated
Max Switch Voltage: 300 VDC/250 VAC*
Max Power:
Max Switch Current:
Max Continuous Carry Current:
Max Pulsed Carry Current
Example (for a single switch path):
62.5 VA, 60 W
2 A
2 A
6 A for 100 ms
(up to 10 % duty cycle)
Initial Path Resistance
On (Single Module):
Off (Single Module):
Differential Thermal Offset:
<850 mΩ (X to X)
<750 mΩ (X to Y)
>109 Ω
5 µV (typical)
Operate Time: <3 ms
Max Number of Simultaneously
Closed Crosspoints: BRIC4: 50
BRIC8: 100
Expected Life (operations)
Very low power signal load:
Low power load (2 W):
Medium power load (30 W):
Full power load (60 W):
>1x108
>1.5x107 (0.1 A 20 VDC)
>5x106 (1 A 30 VDC)
>1x105 (2 A 30 VDC)
* For full voltage rating, signal sources to be switched must
be fully isolated from mains supply and safety earth.
Power Requirements
+3.3 V +5 V +12 V -12 V
310 mA
(typical)
4 A max (fully loaded BRIC8,
100 crosspoints energised),
typically <2A
40 mA 0
40-566B
pickeringtest.com Page 6
Specifications

Page 1.7
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
Product Order Codes
BRIC4 - 4-Slot High Density Matrix
2 A, 2-Pole, 55x4 Matrix
2 A, 2-Pole, 110x4 Matrix
2 A, 2-Pole, 165x4Matrix
40-566B-001
40-566B-002
40-566B-003
BRIC8 - 8-Slot High Density Matrix
2 A, 2-Pole, 55x4 Matrix
2 A, 2-Pole, 110x4 Matrix
2 A, 2-Pole, 165x4 Matrix
2 A, 2-Pole, 220x4 Matrix
2 A, 2-Pole, 275x4 Matrix
2 A, 2-Pole, 330x4 Matrix
2 A, 2-Pole, 385x4 Matrix
40-566B-101
40-566B-102
40-566B-103
40-566B-104
40-566B-105
40-566B-106
40-566B-107
For the expansion of an existing BRIC matrix or replacement
of faulty BRIC daughter cards please contact your local sales
office.
Product Customization
Pickering PXI modules are designed and manufactured on
our own flexible manufacturing lines, giving complete product
control and enabling simple customization to meet very
specific requirements.
Customization can include:
• Alternative relay types
• Mixture of relay types
• Alternative number of relays
• Different performance specifications
All customized products are given a unique part number, fully
documented and may be ordered at any time in the future.
Please contact your local sales office to discuss.
Special Versions
BRIC modules can be built in special versions, for example
where an exact matrix size is required then partly
populated daughtercards may be ordered.
Upgrading With Daughtercards
BRIC modules can be upgraded to a larger matrix size
using daughtercards, please consult your local sales office
for further information.
Support Products
BIRST Adapter
For the BIRST tool to achieve full relay coverage the
supplied 44-566A-BAT4 adapter is required to allow the
front panel Y isolation switches to be tested. The adapter
consists of a pre-wired 160-pin DIN41612 socket with
back-shell, and is fitted to the front panel connector during
testing.
eBIRST Switching System Test Tool
This product is supported by the eBIRST test tools which
simplify the identification of failed relays, the required
eBIRST tools are below. This product requires master slave
testing and two sets of tools are required together with the
master slave cable: 93-970-301. For more information go to:
pickeringtest.com/ebirst
Connector Test Tool Adaptor
160-pin DIN41612
25-pin D-type
93-002-001
93-005-001
93-002-410
93-005-414
Spare Relay Kits
Kits of replacement relays are available for the majority of
Pickering’s PXI switching products, simplifying servicing and
reducing down-time.
Product Relay Kit
40-566B-xxx 91-100-001
For further assistance, please contact your local Pickering
sales office.
Mating Connectors & Cabling
For connection accessories for the 40-566B module please
refer to the 90-001D 160-pin DIN 41612 and 90-008D 25-pin
D-type Connector Accessories data sheet where a complete
list and documentation can be found for accessories, or refer
to the Connection Solutions catalog.
40-566B
pickeringtest.com Page 7
Ordering Information

Page 1.8 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
40-566B
pickeringtest.com Page 8
Supporting Products & Software
Chassis Compatibility
This PXI module must be used in a suitable chassis. It is compatible with the following chassis types:
• All chassis conforming to the 3U PXI and 3U Compact PCI (cPCI) specification
• Legacy and Hybrid Peripheral slots in a 3U PXI Express (PXIe) chassis
• Pickering Interfaces LXI or LXI/USB Modular Chassis
Chassis Selection Guide
Pickering LXI or LXI/USB Modular Chassis
Only accept our PXI Switching & Simulation Modules:
• Choose from 1000+ Pickering PXI Modules
• Ethernet or USB control enables remote
operation
• Low-cost control from practically any
controller
• LXI provides manual control via Web
browsers
• Driverless software support
• Power sequencing immunity
• Ethernet provides chassis/controller
voltage isolation
• Independence from Windows
operating system
Standard PXI or hybrid PXIe Chassis From Any Vendor:
• Mix our 1000+ PXI switching &
simulation modules with any
vendor’s PXI instrumentation
• Embedded or remote Windows
PC control
• Real-time Operating System Support
• High data bandwidths, especially
with PXI Express
• Integrated module timing and
synchronization

Page 1.9
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
40-566B
pickeringtest.com Page 9
Supporting Products & Software
Connectors
& Backshells
Multi-way
Cable Assemblies
RF Cable
Assemblies
Breakouts
Connectivity Solutions
We provide a full range of supporting cable and connector solutions for all our switching
products—20 connector families with 1200+ products. We offer everything from simple
mating connectors to complex cables assemblies and terminal blocks. All assemblies are
manufactured by Pickering and are guaranteed to mechanically and electrically mate to our
modules. These accessories are detailed in Connector Accessories data sheets, where a
complete list and documentation can be found for each accessory.
Connector
Blocks
We also offer customized cabling and have a free online Cable Design Tool that can be used to create custom cable solutions for
many applications.
• Fully supported on modern browsers and tablet operating systems.
• Built-in tutorials and videos allow you to get quickly up to speed.
• Store cable assemblies in the Cloud and develop over time.
• Each cable design has a downloadable PDF documentation file
detailing all specifications
Start designing your custom cabling, go to pickeringtest.com/cdt
Mass Interconnect
We recommend the use of a mass interconnect solution when an Interchangeable Test Adapter (ITA) is required for PXI/LXI
based test systems. Our modules are fully supported by Virginia Panel and MacPanel.
Pickering Reed Relays
We are the only switch provider with in-house reed relay manufacturing capability
via our Relay Division. These instrument grade reed relays feature SoftCenter™
technology, ensuring long service life and repeatable contact performance.
To learn more go to pickeringrelay.com

Page 1.10 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
40-566B
pickeringtest.com Page 10
Supporting Products & Software
Programming
Pickering provide kernel, IVI and VISA (NI & Keysight) drivers which are compatible with all Microsoft supported versions of
Windows and popular older versions.
For more information go to pickeringtest.com/os
The VISA driver support is provided for LabVIEW Real Time Operating Systems (Pharlap and Linux-RT). For other RTOS support
contact Pickering. These drivers may be used with a variety of programming environments and applications including:
• Pickering Interfaces Switch Path Manager
• National Instruments products (LabVIEW, LabWindows/CVI, Switch Executive, MAX, TestStand, VeriStand, etc.)
• Microsoft Visual Studio products (Visual Basic, Visual C++)
• Programming Languages C, C++, C#, Python
• Keysight VEE and OpenTAP
• Mathworks MATLAB, Simulink
• Marvin ATEasy
• MTQ Testsolutions Tecap Test & Measurement Suite
Drivers for popular Linux distributions are available, other environments are also supported, please contact Pickering
with specific enquiries. We provide Soft Front Panels (SFPs) for our products for familiarity and manual control, as well as
comprehensive documentation and example programs to help you develop test routines with ease.
To learn more about software drivers and development environments go to pickeringtest.com/software
DMM+ R3a
S+ R3b
DMM- R3c
S- R3d
DMM
S+ S-
DMM+ DMM-
aX1 aX3
aX4
aX7 aX9 aX11 aX13 aX15 aX17 aX19 aX21 aX23 aX25 aX27 aX31
aY1
aY2
aY3
aY4
Switch 1
bY1
bY2
bY3
bY4
bY5
bY6
bY7
bY8
bX1 bX5 bX7 bX9 bX11 bX13 bX15 bX17 bX19 bX21 bX23
R3a R3b
R3c R3d
Switch 2 Device Under Test
Signal Routing Software
Our signal routing software, Switch Path Manager,
automatically selects and energizes switch paths
through Pickering switching systems. Signal
routing is performed by simply defining test
system endpoints to be connected together, greatly
accelerating Test System software development.
To learn more go to pickeringtest.com/spm

Page 1.11
2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering SECTION 1 - TECHNICAL SPECIFICATION
40-566B
pickeringtest.com Page 11
Supporting Products & Software
© Copyright (2023) Pickering Interfaces. All Rights Reserved
Pickering Interfaces maintains a commitment to continuous product development, consequently we reserve the right to vary from the description given in this data sheet.
Diagnostic Relay Test Tools
eBIRST Switching System Test Tools are designed
specifically for our PXI, PCI or LXI products, these tools
simplify switching system fault-finding by quickly testing
the system and graphically identifying the faulty relay.
To learn more go to pickeringtest.com/ebirst
Three Year Warranty & Guaranteed Long-Term Support
All standard products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for
three years from the date of delivery to the original purchaser. Extended warranty and service agreements are available with
various levels for your requirements. Although we offer a 3-year warranty as standard, we also include guaranteed long-term
support—with a history of supporting our products for typically 15-20 years.
To learn more go to pickeringtest.com/support
Available Product Resources
We have a library of resources including success stories, product and support videos, articles and white papers as well as
application-specific brochures to assist you. We have also published reference books on switching technology and the PXI and
LXI standards.
To view, download or request any of our product resources go to pickeringtest.com/resources
B
B
IRST
IRST
e
e

Page 1.12 2 A BRIC Multi-Slot Matrix with BIRST™ - 40-566B
pickering
SECTION 1 - TECHNICAL SPECIFICATION
THIS PAGE INTENTIONALLY BLANK