Pinnacle Climate Technologies REMINGTON REM-80T-KFA-B Training manual

MODEL NUMBERS:
REM-45-KFA-B / REM-80T-KFA-B / REM-140T-KFA-B / REM-175T-KFA-B / REM-215T-KFA-B
CONSUMER: READ AND SAVE THESE INSTRUCTIONS
GENERAL HAZARD WARNING: READ AND UNDERSTAND ALL OF THE
INSTRUCTIONS IN THIS MANUAL BEFORE ASSEMBLING, STARTING,
OR SERVICING THE HEATER. Be sure to comply with the instructions and
warnings provided with this heater. Failure to comply can result in fire or
explosion that can cause property loss, bodily injury, or loss of life. Persons who are impaired or under the
influence of alcohol or drugs should not operate heater. Only persons who can follow and understand these
instructions should operate or service this heater. If you need heater info; such as an operating manual, labels,
etcetera, contact Pinnacle Climate Technologies at 800-641-6996.
DANGER
NOT FOR USE IN RESIDENTIAL LIVING AREAS OR IN ENCLOSED
SPACES WITHOUTADEQUATEVENTILATION. THIS HEATER IS
SUITABLE FOR OUTDOOR USE, AND INDOOR USE ONLY IN WELL
VENTILATED AREAS. INDOOR USE PERMITTED ONLY FOR: THE TEMPORARY HEATING OF
ADEQUATELY VENTILATED BUILDINGS OR STRUCTURES UNDER CONSTRUCTION, ALTERATION
OR REPAIR. This is an unvented portable heater that uses air (Oxygen) from within the area in which it
is used. Failure to provide adequate combustion and ventilation air will result in asphyxiation, carbon
monoxide poisoning, bodily injury or death. Refer to “Ventilation” on Page 6.
FACTORY ID: 500
DANGER
Sauk Rapids, MN 56379 USA • Toll Free [phone]
Fax: [phone] • Web: www.remingtonheater.com • Email: [email protected]
© 2022 Pinnacle Climate Technologies, Inc. RBKD-404
User’s Manual &
Operating Instructions
KEROSENE FORCED
AIR HEATER
Locating Your Serial Number:
Your serial number can be found on a white label on the right side cover of your heater. For Example: 150812779.
Have your Serial Number ready before calling customer service at 800-641-6996.

2
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
MASSACHUSETTS RESIDENTS: Massachusetts state law prohibits the use of this heater in any building which
is used in whole or in part for human habitation. Use of this heating device in Massachusetts requires local fire
department permit (M.G.L.C. 148, Section 10A).
NEW YORK CITY RESIDENTS: The New York City Fire Code prohibits the storage, handling and use of
kerosene fueled heaters for space heating. Any person violating that provision may be punished by a fine up to
$10,000 and a term of imprisonment of up to 6 months.
Look for this icon throughout the manual for helpful tips on how to assemble, use and clean your
KFA Heater.
THE INSTALLATION OF THE EQUIPMENT SHALL BE IN ACCORDANCE WITH THE REGULATION OF
AUTHORITIES HAVING JURISDICTION AND CSA STANDARD B139.
WARNING: This product can expose you to chemicals, including lead and lead compounds, which are
known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information go to www. P65Warnings.ca.gov.
DO NOT START THE HEATER WHEN EXCESS OIL HAS ACCUMULATED.
DO NOT START THE HEATER WHEN THE CHAMBER IS HOT.
WARNING
WARNING
FIRE, BURN, INHALATION AND EXPLOSION HAZARD. Keep combustibles
such as; building materials, paper or cardboard a safe distance away from the
heater as recommended by these instructions. Never use the heater in spaces
which contain products such as; gasoline, solvents, paint thinners, dust particles, volatile or airborne combusti-
bles or any unknown chemicals. This is an unvented portable heater. It uses air (Oxygen) from the area in which
it is used. Adequate combustion and ventilation air must be provided. Refer to “Ventilation” on page 6. Bulk
fuel storage should be a minimum of 25 feet (7.6 m) from heater.
WARNING
DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ AND
THOROUGHLY UNDERSTAND THESE SAFETY AND OPERATING
INSTRUCTIONS.
Failure to comply with the precautions and instructions provided with this heater can result in death, serious
bodily injury, property loss or damage from the hazards of fire, soot production, explosions, burns, asphyxiation or
carbon monoxide poisoning. Only persons who can read and understand these instructions should use or service
this heater.
WARNING
SAFETY INFORMATION
Safety Information..............................................................2-3
What’s in the Box...................................................................4
Specifications.........................................................................5
Features..
............................................................................... 5
Assembly Instructions..........................................................5
Operation.............................................................................6-7
Maintenance........................................................................8-9
Wiring Diagrams....................................................................10
Troubleshooting Guide.........................................................11
Exploded View
.................................................................. ... . .12
Parts List...................................................................................13
Limited Warranty....................................................................14
TABLE OF CONTENTS

3
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
SAFETY INFORMATION (CONT.)
ALWAYS use only the electrical power (voltage and frequency)
specified on the model plate of the heater.
ALWAYS use only three-prong, grounded outlet and extension
cord.
ALWAYS use only 14 AWG or better extension cord.
ALWAYS unplug the heater when not in use.
ALWAYS install the heater so that it is not directly exposed to
water spray, rain, dripping water, or wind.
NEVER use fuels such as gasoline, benzine, paint thinners or
other oil compounds in this heater.
NEVER refill the heater’s fuel tank while the heater is
operating or still hot. This heater is EXTREMELY HOT while in
operation.
NEVER block air inlet (rear) or air outlet (front).
NEVER use duct work in front or rear of heater.
NEVER move or handle heater while still hot.
NEVER transport heater with fuel in tank.
NEVER use with an external fuel tank.
Keep all combustible materials away from this heater.
Minimum Clearance From Combustibles
45-175T-KFA 215T-KFA
Top 4 ft. (122 cm) 4 ft. (122 cm)
Sides 4 ft. (122 cm) 4 ft. (122 cm)
Front 8 ft. (244 cm) 10 ft. (305 cm)
ALWAYS locate heater on a stable and level surface.
If your heater is equipped with a thermostat, once it is
plugged in, it can start at anytime in accordance with the
thermostat setting.
RISK OF BURNS, FIRE
AND EXPLOSION!
RISK OF ELECTRIC
SHOCK!
WARNING
WARNING
CAUTION! HOT WHILE
IN OPERATION. DO
NOT TOUCH. KEEP
CHILDREN, ANIMALS, CLOTHING AND COMBUS-
TIBLES AWAY FROM HEATER.
WARNING
The products described in this manual are kerosene
direct-fired, forced air heaters. Kerosene forced air
heaters are primarily intended for use for temporary
heating of buildings under construction, alteration or
repair. Direct-fired means that all of the combustion
products of the heater enter the heated space. This
appliance is rated at 98% combustion eciency, but
does produce small amounts of carbon monoxide.
Carbon monoxide is toxic. Humans can tolerate only
small amounts of carbon monoxide and so precautions
should be taken to provide proper ventilation. Failure
to provide proper ventilation in accordance with the
instructions in this manual can result in death.People
with breathing problems should consult a physician
before using this heater. Early signs of carbon monoxide
poisoning resemble the flu. Symptoms of improper
ventilation/carbon monoxide poisoning are:
Headache • Dizziness •Nausea • Dry Mouth Sore
Throat • Burning of Nose and Eyes
If you experience any of these symptoms:
GET FRESH AIR AT ONCE! Have your heater serviced
and check for proper ventilation. Some people are
more aected by carbon monoxide than others. These
include: pregnant women, those with heart or lung
problems, anemia or those under the influence of
alcohol or at high altitudes.
FOR OUTDOOR USE. INDOOR USE PERMITTED ONLY
FOR: The temporary heating of adequately ventilated
buildings or structures under construction, alteration
or repair. Provide at least a three square foot (2,800
sq cm) opening of outside air for every 100,000 Btu/
Hr (29 kW) heater rating. Refer to “Ventilation” on
page 6 for further instructions.
RISK OF INDOOR AIR
POLLUTION!
WARNING
CARBON MONOXIDE
POISONING MAY LEAD
TO DEATH!
DANGER

4
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
WHAT’S IN THE BOX (45-KFA / 80T-KFA)
- Remove the heater and all packaging materials
from the shipping carton
Note: Save the box and packaging materials
for future storage.
Shown With Optional Cord
Wraps
Cord Wraps (Optional) Carry Handle (1)
10 mm Screws (2) 15 mm Screws (2)
WHAT’S IN THE BOX (140T-KFA / 175T-KFA / 215T-KFA)
Tools Needed:
- Phillips Head Screw Driver
- 8 mm open end wrench
- 19 mm open end wrench
Tip: Be sure to remove the axle from the side of the
Styrofoam packaging.
Tip: Use a power screwdriver and locking wrench
for easier assembly.
Front Handle
Axle
Rear Handle
Wheel Support Frame
50 mm Screws (4) 30 mm Screws (4) 8 mm Nuts (8) Wheels (2)
Axle Nuts (2) Spacers (2)
Heater (1)
Heater (1)

5
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
ASSEMBLY INSTRUCTIONS (140T-KFA / 175T-KFA / 215T-KFA)
1. Insert axle through holes in wheel support.
2. Slide spacer onto axle.
3. Slide wheel onto axle and hold in place with the axle
nuts (see Figure 1).
4. Place heater on wheel support and line up holes on
the fuel tank lip.
5. Attach front handle with (2) long screws (50 mm) and
(2) nuts through the second hole from the front on
both sides of the tank lip and wheel support frame and
tighten firmly.
6. Insert (2) short screws (30 mm) through the first hole
from the front in the tank lip and tighten firmly. Make
certain all (4) screws are secure.
7. Attach rear handle with (2) long screws
(50 mm) and (2) nuts through the second hole from the
rear of the heater on either side (see Figure 2).
8. Tilt the heater up gently so it is resting on the front
handle.
NOTE: DO NOT do this if there is fuel in the tank.
9. Remove the wheels to secure the second set of screws
through the rear handle.
10. Secure the rear handle with (2) short screws (30 mm)
and (2) nuts and tighten
firmly.
11. Replace wheels and
tighten with the wheel
nuts.
12. Tilt heater back down
onto wheels and check
all screws and nuts to en-
sure they are secure.
Figure 1
Axle
Axle Nut
Spacer
Tire
Wheel Support Frame
Figure 2
SPECIFICATIONS
Model # 45-KFA 80T-KFA 140T-KFA 175T-KFA 215T-KFA
Rating: Btu/Hr / kW 45,000 / 13.19 80,000 / 23.4 140,000 / 41 175,000 / 51.3 215,000 / 63.01
Fuel Consumption: Gal/Hr / L/Hr 0.35 / 1.32 0.63 / 2.38 1.1 / 4.16 1.34 / 5.1 1.63 / 6.17
Fuel Tank Capacity: Gallons / Liters 5 / 19 5 / 19 10 / 38 13 / 49 13 / 49
Pump Pressure: psi / BAR 3.0 / 0.21 4.2 / 0.29 6.6 / 0.46 7.5 / 0.52 9.0 / 0.62
Volts: AC/Hz
120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz
Amps 1.4 1.5 2.4 2.7 2.8
Phase Single Single Single Single Single
Specifications subject to change without notice.
FEATURES
Hot Air Outlet
Upper Shell
Handle
Extension Cord Wrap
Fan Guard
Pressure Gauge
Fuel Gauge
Fuel Cap
Power Cord
Fuel Tank
Power/Reset Switch
Thermostat Knob
(80T KFA Only)
Lamp
Lower Shell
Upper Shell
Power
Cord
Drain Bolt
Fuel Tank
Pressure
Gauge
Fan Guard
Rear Handle
Digital Temperature
Display
Lamp
Thermostat
Knob
Fuel Cap
Fuel Gauge
Lower Shell
Hot Air
Outlet
Front
Handle

6
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
Fueling The Heater:
Kerosene (K-1)
For optimal performance of this heater, it is strongly
suggested that K-1 kerosene be used, especially in
temperatures lower than 26°F (-3°C). K-1 kerosene has
been refined to virtually eliminate contaminants, such
as sulfur, which can cause a rotten egg odor during the
operation of the heater. Using diesel fuel can cause
excess soot production. Do not use Bio-Diesel as this
fuel will damage your heater’s seals and filter.
- CSA certified for use with K-1 kerosene, no. 1 & no.
2 diesel, JP8/Jet A Fuel, no. 1 and no. 2 fuel oil.
DO NOT use any fuel that is not approved above.
- NEVER use fuel such as, benzene, alcohol, white gas,
camp stove fuel, paint thinners, or other oil compounds
in this heater. THESE ARE VOLATILE FUELS THAT CAN
CAUSE A FIRE OR EXPLOSION.
- NEVER store kerosene in the living space. Kerosene
should be stored in a well ventilated area outside the
living area.
- NEVER store kerosene in direct sunlight or near a source
of heat.
- NEVER use kerosene that has been stored from one
season to the next. Kerosene deteriorates over time.
OLD KEROSENE WILL NOT BURN PROPERLY IN THIS
HEATER.
NOTE: Kerosene should only be stored in a blue container
that is clearly marked “Kerosene.” Never store kerosene in
a red container. Red is associated with gasoline.
Ventilation:
- Risk of indoor air pollution and Carbon Monoxide
Poisoning. Use heater only in well ventilated areas.
- Refer to Safety Information on page 3 for information
about Carbon Monoxide Poisoning.
- ALWAYS provide a fresh air opening in the heated space
of at least three square feet (2,800 sq. cm) for each
100,000 Btu / Hr. (29 kW) of heater output. Provide a
larger opening if more heaters are being used.
Minimum Ventilation Opening Needed
45-KFA 80T-KFA 140T-KFA
1.4 ft.² 2.4 ft.² 4.2 ft.²
1250 cm² 2230 cm² 3902 cm²
Minimum Ventilation Opening Needed
175T-KFA 215T-KFA
5.3 ft.² 6.5 ft.²
4930 cm² 5990 cm²
OPERATION
NEVER FILL
THE FUEL TANK
INDOORS. ALWAYS
FILL THE TANK OUTDOORS. BE SURE THAT THE
HEATER IS ON LEVEL GROUND WHEN FUELING,
AND NEVER OVERFILL THE TANK.
CAUTION
CARBON MONOXIDE POISONING MAY LEAD TO DEATH!
DANGER
DO NOT USE
GASOLINE OR
CRANKCASE
DRAININGS.
WARNING
NEVER REFUEL THIS
HEATER WHILE
IT IS HOT OR
OPERATING. FIRE OR EXPLOSION COULD RESULT.
DANGER

7
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
OPERATION (CONT.)
Starting the Heater: (Ignition)
1. Fill the tank with kerosene or other approved fuel
until needle on fuel gauge points to “F”.
2. Replace fuel cap and tighten firmly.
3. Connect the heater to a three prong
(grounded) power source. You must use a three
prong (grounded) extension cord that is at least 6
feet long and is a minimum of 14 AWG rating.
Model 45-KFA:
1. Complete steps 1-3 above.
2. Move power switch to “On” position. The power
indicator light will illuminate and the heater will
ignite.
Stopping / Restarting Heater:
- To stop the heater, move the power switch to the “O”
position and unplug the power cord.
- To restart the heater; wait 10 seconds and follow ignition
steps.
Models 80T-KFA - 215T-KFA:
1. Complete “starting heater ignition” steps 1-3 above
2. Turn thermostat control knob to desired
temperature setting. The thermostat set range is
from 40 ºF to 110 ºF.
3. Move power switch to “On” position. The power
indicator light and room temperature display will
illuminate and heater will ignite.
NOTE: 45-80T-KFA models do not have a room
temperature display feature.
The room temperature display will indicate the
following:
- When the temperature is less than 0 ºF the
display says “LO”.
- When the temperature is more that 99 ºF the
display says “HI”.
- Between 0 °F and 99 °F the display shows
actual temperature.
Stopping / Restarting Heater:
- To stop the heater, move the power switch to the “O”
position and unplug the power cord.
- To restart the heater; wait 10 seconds and follow ignition
steps.
Long Term Storage:
Models 45-KFA - 80T-KFA:
1. Use an approved siphon to drain fuel through the fuel
cap opening.
Models 140T-KFA - 215T-KFA:
1. Drain fuel through the drain bolt in the bottom of
the fuel tank.
2. To remove the drain bolt, unscrew
counterclockwise.
3. Using a small amount of kerosene, rinse and swirl
the kerosene inside of the fuel tank, empty the
tank fully.
4. To replace the drain bolt; push the drain head fully
into the drain hole and screw clockwise.
IMPORTANT: Never store leftover kerosene between
seasons, using old fuel can damage heater.
TIP: If the heater does not ignite; move switch to
“O” position, check steps 1-3 above and then
move switch to “On” position.
TIP: If the heater does not ignite, the
thermostat may be set too low. Turn the
control knob to a higher setting until the
heater ignites. If the heater does not ignite; move
switch to “Off” position, check steps 1-3 above
and then move switch to “On” position.

8
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
MAINTENANCE
Service:
DO NOT TAMPER WITH THE UNIT. HAVE A
COMPETENT SERVICEMAN MAKE ANY NECESSARY
ADJUSTMENT OR REPAIRS.
Use only original equipment parts. The use of alternate
or third party components can cause unsafe operating
conditions and will void your warranty.
We suggest following a maintenance schedule as follows:
FUEL / FUEL TANK:
Flush tank every 200 hours of operation or as needed.
DO NOT flush with water; use fresh K-1 kerosene only.
AIR FILTERS:
The air intake filter should be replaced or washed with
soap and water and dried thoroughly every 500 hours of
operation or less depending on conditions.
The output and lint filters should be replaced every
500 hours of operation or less depending on
conditions. (See Figure 4)
NOTE: Use of diesel fuel may require additional
maintenance
FAN BLADES:
Blades should be cleaned at least once per heating
season, depending on conditions. Remove all
accumulated dust and dirt with a damp cloth, taking
care not to bend any of the fan blades. Be sure the
blades are dry before re-starting the heater.
FUEL FILTER:
The fuel filter should be cleaned at least twice per
heating season. Clean the filter by rinsing it in clean
K-1 Kerosene. Contaminated fuel could make cleaning
the fuel filter necessary immediately.
NOTE: To remove the filter from models 45 - 80T-
KFA turn filter 90º clockwise. To remove the filter
from models 140T - 215T-KFA turn filter 90º counter-
clockwise. See Figure 3.
THERMISTER PLACEMENT:
Ensure the thermister wire is in the proper place. The
wire should be lying on the bottom shell inside the
heater with the plastic end placed under the motor
support/motor and away from fan blade.
ROTOR:
The rotor with carbon vanes should be evaluated
every heating season. The rotor is behind the air
filters. The vanes should be inspected for damage
or wear. The rotor should be inspected for damage,
chips, wear, cracks.
Check rotor gap: Remove the rear cover. Loosen the
two pump ring screws. Lift the pump ring upwards.
Insert a 0.1 mm feeler gauge and apply slight
downward pressure, enough to offer resistance when
attempting to remove gauge.
Hand-tighten the two pump ring screws. Re-install the
End Pump Cover and the plastic End Filter Cover. Start
the heater and adjust to the proper pump pressure.
Air Output Filter
Intake Filter
Lint Filter End Filter
Figure 4
Never service heater
while it is plugged in or
hot!
WARNING
Figure 3
Fuel Filter
Fuel Line
Side Cover

9
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
MAINTENANCE (CONT.)
Service (Continued):
SPARK PLUG:
Clean and re-gap every 600 hours of operation, or
replace as needed. After removing the spark plug,
clean the terminals with a wire brush. Re-gap the
terminals to 0.140” (3.5mm). See Figure 5.
PHOTOCELL:
The photocell should be cleaned using a cotton swab
dipped in alcohol or water at least once per heating
season, or more depending on conditions.
See Figure 6.
PUMP PRESSURE:
While heater is operating, turn adjusting screw
clockwise to increase, counter-clockwise to decrease
pressure. Correct pump pressure is as follows:
Model Number Pump Pressure
45-KFA 3.0 PSI (0.21 BAR)
80T-KFA 4.2 PSI (0.26 BAR)
140T-KFA 6.6 PSI (0.46 BAR)
175T-KFA 7.5 PSI (0.52 BAR)
215T-KFA 9.0 PSI (0.62 BAR)
Tolerance ± 10%
NOZZLES:
Nozzles should be cleaned or replaced at least once
per heating season. Contaminated fuel could make
this necessary immediately. To clean dirt from nozzle,
blow compressed air through nozzle front. It may be
necessary to soak the nozzle in K-1 kerosene to loosen
any dirt particles.
Figure 5 Ignitor Wire
Spark Plug
Gap
Burner Head
XX
Figure 6
Photocell Photocell lens
Photocell
Wire
Figure 8
Adjusting Screw
Pressure Valve
Figure 7
Nozzle
Nozzle Face
Burner Head

10
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
WIRING DIAGRAMS
CONTROL PCB
POWER LAMP
(LED)
CN1 RED
RED
BLACK
BLUE
BLACK
BLACK
BLUE
RED
EARTH
GREEN
SPARK PLUG
IGNITOR
PUMP
MOTOR
CAPACITOR
3.5UF/450VAC
FAN 1
FAN 2
ACIN 1
WHITE
WHITE
EARTH
BLACK
WHITE
BLACK
GREEN
POWER
PLUG
AC 240V
50Hz
LIMIT
CONTROL
POWER
SWITCH
PHOTOCELL
BLACK
BLACK
CDSCN2
YELLOW
FUSE
5A/250AVC
ACIN 2
(80T-KFA)
(140T-KFA)
(175T-KFA / 190T-KFA / 215T-KFA)
Models
140T/175T/190T/215T-KFA have
a digital display.
80T-KFA
140T-KFA / 175T-KFA / 190T-KFA
45-KFA
80T - 215T- KFA

11
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
TROUBLESHOOTING GUIDE
Problem Possible Cause Solution
Heater Ignites, but main PCB shuts o
after a short period of time.
Lamp flickers and LED display shows
“E1”.
1. Incorrect pump pressure.
2. Dirty input, output or lint filter.
3. Dirty fuel filter.
4. Nozzle is dirty.
5. Photocell lens is dirty.
6. Photocell not installed properly.
7. Photocell is defective.
8. Improper electrical connection between
main PCB and photocell.
9. Improper location of thermister sensor
(does not apply to 45-KFA model)
10. Improper electrical connection within the
temperature limit switch
1. Adjust pump pressure.
2. Clean / replace air or lint filter.
3. Clean / replace fuel filter.
4. Clean / replace Nozzle.
5. Clean / replace photocell.
6. Adjust photocell position
7. Replace photocell
8. Check wiring connections
(see wiring diagrams on page 10).
9. Check thermister placement
10. Replace temperature limit switch
Heater will not operate or motor runs for
a short time.
Lamp flickers and LED display shows
“E1”.
1. No kerosene in the fuel tank.
2. Incorrect pump pressure.
3. Corroded spark plug or incorrect plug
gap.
4. Dirty fuel filter.
5. Dirty nozzle.
6. Moisture in fuel tank.
7. Improper electrical connection between
transformer and circuit board.
8. Ignitor wire not connected to spark
plug.
9. Defective ignitor.
10. Improper spacing with rotor
1. Fill tank with fresh kerosene.
2. Adjust pump pressure.
3. Clean / replace spark plug.
4. Clean / replace fuel filter.
5. Clean / replace nozzle.
6. Rinse fuel tank with clean, fresh
kerosene.
7. Inspect all electrical connections (see
wiring diagrams on page 10).
8. Re-attach ignitor wire to spark plug.
9. Replace ignitor.
10. Adjust rotor
Fan does not operate when heater is
plugged in and power switch is in the
“ON” position. The lamp is flickering or
and LED display shows “E1” or “E2”.
1. Thermostat is set too low (does not
apply to 45-KFA model).
2. Broken electrical connection between
main PCB and motor.
1. Rotate thermostat to a higher setting
2. Inspect all electrical connections (see
wiring diagrams on page 10).
Lamp is flickering and LED display
shows “E3”.
1. Thermostat switch has failed. 1. Replace thermostat switch (see Wiring
diagrams on page 10).
Poor combustion and / or excess soot
production.
1. Dirty input, output or lint filter.
2. Dirty fuel filter.
3. Poor quality of fuel.
4. PSI is too high or too low.
5. Dirty nozzle
1. Clean / replace air or lint filter.
2. Clean / replace fuel filter.
3. Flush fuel tank and refuel heater.
4. Use proper pressure.
5. Clean / replace nozzle
Heater does not turn on and the lamp is
not lit.
1. Temperature limit sensor has
overheated.
2. No electrical power.
3. Fuse is blown.
4. Improper electrical connection between
temperature limit sensor and circuit
board.
1. Push power switch to “OFF and allow
heater to cool for 10 minutes. Restart
heater.
2. Check power cords for proper
connection and test the power supply.
3. Check / replace the fuse.
4. Inspect all electrical connections (see
wiring diagrams on page 10).

12
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
13
1012
8
11
929
25
3
15
2
4
6
1**
7
21
23
16
17
18
20 30
19
14
40**
32*
34**
35**
28
27
5
31
30
24
26
37**
36**
38**
33**
41
22
EXPLODED VIEW
* 45-KFA - 80T-KFA Only
** 140T-KFA - 215T-KFA Only

13
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
PARTS LIST
TIP: To order parts call 800-641-6996.
#Description 45-KFA 80T-KFA 140T-KFA 175T-KFA 215T-KFA
1Drain Bolt ––70-002-0115 70-002-0115 70-002-0115
2Fuel Gauge 70-007-0110 70-007-0110 70-007-0215 70-007-0215 70-007-0215
3Fuel Filter 70-003-0100 70-003-0100 70-003-0200 70-003-0200 70-003-0200
4Fuel Cap - Large Plastic 70-006-0140 70-006-0140 70-006-0140 70-006-0140 70-006-0140
5Power Cord 70-034-0100 70-034-0100 70-034-0205 70-034-0205 70-034-0205
6Power Switch 70-038-0100 70-038-0100 70-038-0100 70-038-0100 70-038-0100
7Thermostat Control Knob – 70-031-0100 70-031-0100 70-031-0100 70-031-0100
8Air Line 70-035-0100 70-035-0200 70-035-0300 70-035-0400 70-035-0500
9Thermostat Limit Control 70-019-0100 70-019-0100 70-019-0100 70-019-0100 70-019-0200
10 Photocell Bracket 70-010-0101 70-010-0101 70-010-0101 70-010-0101 70-010-0101
11 Fuel Line 70-036-1010 70-036-1010 70-036-1020 70-036-1030 70-036-1040
12 Photocell 70-016-0100 70-016-0100 70-016-0100 70-016-0100 70-016-0100
13 Burner Head Assembly 70-014-0101 70-014-0101 70-014-0301 70-014-0301 70-014-0301
14 Nozzle Kit 70-015-0100 70-015-0205 70-015-0310 70-015-0410 70-015-0500
15 Spark Plug Kit 70-052-0100 70-052-0100 70-052-0200 70-052-0200 70-052-0200
16 Motor 70-021-0500 70-021-0500 70-021-0510 70-021-0520 70-021-0520
17 Pump Body 70-020-0101 KT-025 KT-025 KT-024 KT-024
18 Rotor Kit 70-022-0100 KT-025 KT-025 KT-024 KT-024
19 End Pump Cover 70-020-0102 70-020-0102 70-020-0102 70-020-0102 70-020-0102
20 Filter Kit 70-054-0100 70-054-0100 70-054-0100 70-054-0100 70-054-0100
21 End Filter Cover 70-020-0103 70-020-0103 70-020-0103 70-020-0103 70-020-0103
22 Pump Adjustment Kit 70-055-0100 70-055-0100 70-055-0100 70-055-0100 70-055-0100
23 Capacitor 70-020-0125 70-020-0125 70-020-0200 70-020-0201 70-020-0201
24 Fan 70-024-0100 70-024-0200 70-024-0300 70-024-0400 70-024-0400
25 Ignitor 70-037-0350 70-037-0350 70-037-0350 70-037-0350 70-037-0350
26 Fan Guard 70-016-0700 70-016-0700 70-016-0200 70-016-0200 70-016-0200
27 Main PCB Assembly 70-027-0100 70-027-0200 70-027-0300 70-027-0300 70-027-0300
28 Fuse 70-027-0101 70-027-0101 70-027-0101 70-027-0101 70-027-0101
29 Clip Nut 70-001-0106 70-001-0106 70-001-0106 70-001-0106 70-001-0106
30 Air Pressure Gauge – 70-025-0100 70-025-0100 70-025-0100 70-025-0100
31 Cord Bushing 70-033-0100 70-033-0100 70-033-0200 70-033-0200 70-033-0200
32 Handle 70-001-0103 70-001-0103 – – –
33 Front Handle – – 70-042-0100 70-042-0250 70-042-0250
34 Rear Handle – – 70-043-0105 70-043-0205 70-043-0205
35 Wheel Support Frame – – 70-041-0700 70-041-0710 70-041-0710
36 Wheel Axle – – 70-041-0115 70-041-0205 70-041-0205
37 Wheel – – 70-041-1400 70-041-1400 70-041-1400
38 Wheel Nut – – 70-041-0550 70-041-0550 70-041-0550
39 Hardware Kit (not pictured) 70-056-0100 70-056-0100 70-056-0210 70-056-0210 70-056-0210
40 Cord Wrap 70-032-0100 70-032-0100 70-032-0200 70-032-0200 70-032-0200
41 Motor Supporter 70-020-0600 70-020-0600 70-020-0610 70-020-0610 70-020-0610

14
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR
WHILE CONNECTED TO A POWER SOURCE
© 2022 Pinnacle Climate Technologies, Inc. Kerosene Forced Air Heater User’s Manual
LIMITED WARRANTY
Pinnacle Climate Technologies, Inc. warrants this heater to
the original retail purchaser only, to be free from defects in
material and workmanship for a period of one (1) year from
the date of initial purchase. This product must be properly
installed, maintained and operated in accordance with the
instructions provided.
Pinnacle Climate Technologies, Inc. requires reasonable
proof of your date of purchase from an authorized retailer
or distributor. Therefore, you should keep your sales slip,
invoice or cancelled check from the original purchase.
This Limited Warranty shall be limited to the repair or
replacement of parts, which prove defective under normal
use and service within the warranty period, and which
Pinnacle Climate Technologies , Inc. shall determine at its
reasonable discretion.
This warranty does not apply to products purchased for
rental use.
This Limited Warranty does not cover any failures or
operating diculties due to normal wear and tear, accident,
abuse, misuse, alteration, misapplication, improper
installation or improper maintenance and service by you
or any third party. Failure to perform normal and routine
maintenance on the heater, shipping damage, damage
related to insects, birds or animals of any kind, and damage
due to weather conditions are also not covered.
In addition, the Limited Warranty does not cover damage
to the finish, such as scratches, dents, discoloration, rust or
other weather damage, after purchase.
All transportation costs for the return of damaged product
or parts will be the responsibility of the purchaser. Upon
receipt of damaged item, Pinnacle Climate Technologies,
Inc. will examine the item and determine if defective.
Pinnacle Climate Technologies, Inc. will repair or replace
and return the item, freight pre-paid.
If Pinnacle Climate Technologies, Inc. finds the item to
be in normal operating condition, or not defective the item
will be returned freight collect. This Limited Warranty is
in lieu of all other express warranties. Pinnacle Climate
Technologies, Inc. disclaims all warranties for products that
are purchased from sellers other than authorized dealers or
distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS
WARRANTY EXPIRES, Pinnacle Climate Technologies,
Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR APPLICATION. FURTHER, Pinnacle
Climate Technologies, Inc. SHALL HAVE NO LIABILITY
WHATSOEVER TO PURCHASER OR ANY THIRD PARTY
FOR ANY SPECIAL, INDIRECT, PUNITIVE INCIDENTAL,
OR CONSEQUENTIAL DAMAGES. Pinnacle Climate
Technologies, Inc. assumes no responsibility for any defects
caused by third parties. This Limited Warranty gives the
purchaser specific legal rights; a purchaser may have other
rights depending upon where he or she lives. Some states
do not allow the exclusion or limitation of special, incidental
or consequential damages, or limitations on how long a
warranty lasts, so the above exclusion and limitations may
not apply to you.
Pinnacle Climate Technologies, Inc. does not authorize any
person or company to assume for it any other obligation
or liability in connection with the sale, installation, use,
removal, return or replacement of its equipment, and no
such representations are binding on Pinnacle Climate
Technologies, Inc.
Always be sure to specify the model number and serial
number when making any claim with Pinnacle Climate
Technologies, Inc. For your convenience, use the space
provided below to list this information.
Model #:________________________________
Serial #:________________________________
Date of Purchase: ________________________
Locating Your Serial Number:
Your serial number can be found on a white label on the right side cover of your heater. It will be a
series of 9 digits. For Example: 131234956. Have your Serial Number ready before calling customer
service at 800-641-6996.
Serial Number Label
XX-X-XXXXXX