Pinnacle Climate Technologies REMINGTON REM-18-PCH-O Training manual

CONSUMER: READ AND SAVE THESE INSTRUCTIONS
RGCB-400
GENERAL HAZARD WARNING:
FAILURE TO COMPLY WITH THE PRECAUTIONS AND
INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN
RESULT IN DEATH, SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE
FROM HAZARDS OF FIRE, EXPLOSION, BURN. ASPHYXIATION, CARBON MONOXIDE
POISONING AND / OR ELECTRIC SHOCK. ONLY PERSONS WHO CAN UNDERSTAND
AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER. IF YOU
NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTIONS
MANUAL, LABEL, ETC. CONTACT THE MANUFACTURER.
FIRE, BURN, INHALATION, AND EXPLOSION HAZARD. KEEP SOLID
COMBUSTIBLES, SUCH AS BUILDING MATERIALS, PAPER OR
CARDBOARD, A SAFE DISTANCE AWAY FROM THE HEATER AS
RECOMMENDED BY THESE INSTRUCTIONS. NEVER USE THE HEATER IN SPACES WHICH
DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES, OR PRODUCTS SUCH AS
GASOLINE, SOLVENTS, PAINT THINNERS, DUST PARTICLES OR UNKNOWN CHEMICALS.
Model Numbers
REM-18-PCH-O
Factory ID: 001
Safety Information
DANGER
WARNING
NOT FOR HOME OR RECREATIONAL VEHICLE USE.
Carbon Monoxide Hazard This heater produces carbon
monoxide, which has no odor. Burning the heater in an enclosed
space can kill you. Never use the heater in enclosed spaces such
as a tent, a camper, any vehicle or recreational vehicle (RV), enclosed shelter, or any other
enclosed areas.
If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or
loss of life.
WARNING
DANGER
DANGER
1 Industrial Blvd #101, Sauk Rapids, MN 56379 USA • Toll Free [phone]
Fax: [phone] • Web: www.remingtonheater.com • Email: [email protected]
© 2017 Pinnacle Climate Technologies, Inc.
User’s Manual &
Operating Instructions
CABINET HEATER

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
This is an unvented portable heater. It uses air (oxygen) from the
area in which it is used. Adequate combustion and ventilation air
must be provided. Refer to VENTILATION on Page 9.
Not for use in residential living areas or in non-adequately venti-
lated enclosed spaces. Never bring or store a propane cylinder
indoors.
DO NOT OPERATE THIS HEATER UNTIL YOU HAVE READ
AND THOROUGHLY UNDERSTAND THESE SAFETY AND
OPERATING INSTRUCTIONS.
Failure to comply with the precautions and instructions provided with this heater can result
in death, serious bodily injury, property loss or damage from the hazards of fire, explosions,
burns, asphyxiation or carbon monoxide poisoning. Only persons who can read and
understand these instructions should use or service this heater.
CALIFORNIA RESIDENTS: This product contains chemicals,
including lead, known to the State of California to cause birth
defects or other reproductive harm. Wash hands after handling.
EXTREMELY HOT DURING OPERATION! Do Not touch any
metal components while in operation. Keep gasoline and any other
flammable liquids away from hater.
1
DANGER
WARNING
WARNING
WARNING
WARNING
CARBON
MONOXIDE
POISONING MAY
LEAD TO DEATH!
The products described in this manual are
propane direct-red, forced air heaters. Propane
forced air heaters are primarily intended for
use for temporary heating of buildings under
construction, alteration or repair. Direct-red
means that all of the combustion products of the
heater enter the heated space. This appliance
is rated at 98% combustion efciency, but does
produce small amounts of carbon monoxide.
Carbon monoxide is toxic. Humans can tolerate
only small amounts of carbon monoxide and so
precautions should be taken to provide proper
ventilation. Failure to provide proper ventilation
in accordance with the instructions in this manual
can result in death.
People with breathing problems should consult a
physician before using this heater.
Early signs of carbon monoxide poisoning
resemble the u. Symptoms of improper
ventilation / carbon monoxide poisoning are:
Headache • Dizziness • Nausea • Dry Mouth
Sore Throat • Burning of Nose and Eyes
If you experience any of these symptoms:
GET FRESH AIR AT ONCE! Have your heater
serviced and check for proper ventilation. Some
people are more affected by carbon monoxide
than others. These include: pregnant women,
those with heart or lung problems, anemia or those
under the influence of alcohol or at high altitudes.
FOR OUTDOOR USE. INDOOR USE
PERMITTED ONLY FOR: The temporary
heating of adequately ventilated buildings or
structures under construction, alteration or
repair! Provide at least a three square foot
(2,800 sq cm) opening of outside air for
every 100,000 Btu / Hr heater rating. Refer to
“Ventilation” on page 8 for further instructions.
Safety Information
RISK OF INDOOR
AIR POLLUTION!
WARNING
DANGER

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Safety Information
WHAT TO DO IF THE SMELL OF GAS IS PRESENT:
–DO NOT attempt to light the heater.
–Extinguish any open ame.
–Shut off gas to heater.
–If odor continues, contact your local gas
supplier or re department.
–DO NOT touch or use any electric switch or
any electric device that can cause a spark.
–Immediately call your gas supplier from a
neighbors phone. Follow the gas suppliers
instructions.
–If you can not reach your gas supplier, call
the re department.
–Service must be done by a qualied
service agency.
NEVER store or use gasoline or other ammable
vapors and liquids in the vicinity of this heater.
NEVER store a propane (LP) cylinder not
connected to this heater in the vicinity of this heater.
NEVER connect heater to an unregulated gas supply.
NEVER obstruct the flow of combustion and
ventilation air.
NEVER use duct work in front or rear of heater.
NEVER modify this heater or operate a heater that
has been modified.
NEVER service, move or handle heater while still
hot or operating
Keep all combustible materials away from this heater.
Minimum Clearance From Combustibles
Front Sides Top
72 in. 12 in. 24 in.
–ALWAYS install the heater so that it is not directly
exposed to water spray, rain, dripping water, or
wind.
– Use heater in accordance with all local codes
and with CSA 5.90 U.S. (5th Ed.) Infrared
Patio Heater.
–This heater is shipped from the factory
for use with propane (LP) gas only. Do not
convert to any other gas. Installation must
conform to local codes, or in their absence,
with the standard for the Storage and
Handling of Liquefied Petroleum Gases ANSI/
NFPA 58 and the Natural Gas and Propane
Installation Code CSA B149.1.
– Gas supply connections should be checked
by using a 50/50 soap and water solution.
Never use a ame to check for gas leaks.
– Use only the regulator and hose assembly
provided with this heater. Inspect the
regulator/hose assembly prior to each use of
the heater. If there is excessive abrasion or
wear, or if the hose is cut, replace it with the
proper assembly shown in the parts list, prior
to using the heater.
– This heater is not for use on nished oors.
Minimum and Maximum Inlet
Pressure
Model 18-PCH-O
Min. 5 PSI
Max. Bottle Pressure
RISK OF BURNS,
FIRE AND
EXPLOSION!
PROPANE IS AN
EXPLOSIVE GAS.
CAUTION!
HOT WHILE IN
OPERATION. DO
NOT TOUCH. KEEP CHILDREN, ANIMALS,
CLOTHING AND COMBUSTIBLES AWAY
FROM HEATER.
2
DANGER
WARNING
WARNING
For use with
propane (LP) gas
only.
The hose assembly
shall be protected
from traffic, building
material and contact with hot surfaces both
during use and while in storage.
WARNING
WARNING

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
1. Remove all packing items applied to heater
for shipment. Keep plastic cover caps
attached to inlet connector and hose /
regulator assembly for storage.
2. Remove all items from carton
3. Check all items for shipping damage. If the
heater is damaged, promptly inform dealer
where you purchased the heater.
The Propane (LP)
gas pressure
regulator and
hose assembly supplied with the heater
must be used without alteration.
Unpacking
RISK OF FIRE! ALWAYS LOCATE HEATER ON A STABLE AND
LEVEL SURFACE!
3
WARNING
CAUTION
Features
Specications
Model # 18-PCH-O
BTU 6,600 / 12,000 / 18,000
Fuel Consumption (Lbs./hr) 0.31 / 0.56 / 0.83
Heat Settings 3
Maximum Operating Hours 65 / 36 / 24
Required Cylinder Lbs. 20
Fuel Type Propane
Heating Area (Ft.2) 165 / 300 / 450
Specications subject to change without notice.

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Unpacking and Assembly
- Remove heater and base from carton (save
carton and packing materials for later storage)
- Remove all protective packaging protecting
heater during shipping.
- Place heater base on at surface with wheels
on ground.
- Line up holes in bottom of heater cabinet with
locking tabs on top of base (see gure 2)
- Mount heater cabinet to heater base, sliding
tabs through holes in bottom of cabinet and
sliding cabinet backward approximately 1/4" or
until cabinet will not move further back.
- Use thumbscrews to attach heater cabinet to
heater base.
- Inspect heater closely for any damage that may
have occured during shipping. If there is any
damage, return the heater to place of purchase.
Connecting to Gas Supply
IMPORTANT! - Always use a propane (LP)
cylinder that has a connection device that is
compatible with the hose and regulator assembly
supplied.
- Remove the back cover by sliding the cover
straight up and away from the heater body.
Place the LP cylinder on the bottom plate and
replace the back cover.
- To connect LP cylinder, insert regulator end
tting into cylinder valve, rotate coupling nut
clockwise and tighten rmly (see gure 3)
- Open valve on propane cylinder slowly. If the
valve is not opened slowly, the excess ow
check valve in the regulator will stop the ow of
gas. If this should happen, close the valve, wait
one minute (or until you hear the valve click),
and re-open, slowly.
- Be sure to inspect all connections for leaks, by
using a 50/50 mixture of dish soap and water on
all connection. Any bubbles forming indicate a
leak.
Missing Parts? Please Call 866-676-1989 For Assistance
4
The Propane (LP)
gas pressure
regulator and hose
assembly supplied with the heater must be
used without alteration.
Be sure to inspect
the regulator hose
before each use. If
the hose is cut or frayed, replace it with the
manufacturer suggested assembly.
CAUTION
CAUTION

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Operation
Propane Supply / Information:
Propane (LP)
This heater is not supplied with a propane cylinder. Use only
an approved propane cylinder.
LP Characteristics
– Flammable, explosive under pressure, heavier than air
and pools in low areas.
– In its natural state, propane has no odor, but for your
safety an odor that smells like rotten cabbage has been
added.
– Contact of propane (LP) gas with the skin can cause
freeze burns.
– Heater is manufactured for use with propane gas only.
DO NOT attempt to convert to any other gas. Such
modications are dangerous and will void the warranty.
– When heater is not in use, LP Cylinder must be turned
OFF.
– Be sure that the LP Cylinder is located on a level and
stable surface.
– DO NOT use this heater in a basement or below ground
level. Propane is heavier than air and will always seek
the lowest level. If you suspect a leak, shut off the valve
at the LP Cylinder immediately.
The Propane (LP) cylinder must also be equipped with
the following
– A collar to protect the gas valve.
– A shut-off valve terminating a LP cylinder valve outlet
as specied in the American National Standard for
Compressed Gas Cylinder Valve Outlets and Inlets
Connections.
– A safety relief valve having direct communications with
the vapor space of the LP cylinder.
– The heater must operate on vapor withdrawal from the
operating cylinder.
– Always keep LP cylinder fastened and upright.
– Avoid tipping the LP cylinder on its side when
connected to a regulator, since this may cause damage
to diaphragm in the regulator.
– Handle valves with care.
– Never connect an unregulated LP cylinder to a
construction heater.
– DO NOT subject LP cylinder to excessive heat.
– Tightly close the gas shutoff valve on the LP cylinder
after each use.
– All ttings must be protected when disconnected from
the LP cylinder.
– Never store an LP cylinder inside a building or in the
vicinity of an gas burning appliances.
Pre-Lighting Instructions:
Connecting the LP Cylinder
ALL NEW LP CYLINDERS MUST BE PURGED BEFORE
THE FIRST FILLING.
– Turn heater gas valve knob and LP cylinder valve to
OFF position.
– LP cylinder valve equipped with old style tting has
LEFT HANDED THREADS. Turn tting CLOCKWISE to
loosen. Protect this tting when disconnected from LP
cylinder.
– Have your LP cylinder lled by your local propane gas
supplier.
– Some LP cylinders have a bleed-OFF valve. This valve
should be inspected for leaks after each lling of the LP
cylinder. Turn the valve clockwise to close.
– Fasten full propane tank and connect proper tting to
LP cylinder valve by turning COUNTER-CLOCKWISE.
– With heater gas valve knob still in OFF position turn
ON the LP cylinder valve and check for leaks with
soap solution.
Propane is
safe to use
when properly
handled. Careless handling of the LP
cylinder could result in a fire and or an
explosion.
The
disconnected
tank must never
be stored in a building, garage or any
other enclosed area.
5
CAUTION
CAUTION
Purging and
filling of the LP
cylinders must
be performed by personnel who have
been thoroughly trained in accepted
LP gas industry procedures. Failure to
follow these instructions may result in
explosion, fire, severe personal injury or
death.
WARNING

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Operation
Checking For Leaks
– To check for leaks, make up a 50/50 solution
of dish soap and water. Apply this solution
to all gas connections. If bubbles appear,
there is a leak. If a leak is found, turn off
the gas supply, and re-connect the leaking
connection. If the leak persists after several
tries, contact Pinnacle Customer Service at
866-676-1989.
– The installation of this heater must meet all
local codes and/or gas utility requirements. In
the absence of local codes, the National Fuel
Code ANSI Z223.1 should be followed.
– The minimum clearances to any combustible
construction materials must be maintained at
all times (See Page 2).
– Inspect the heater before each use, and at
least annually by a qualied service person.
Supply Valve
Regulator
Hose
Propane Tank
Figure 6
6
EXTREMELY HOT
during operation.
Do Not touch any
metal components while in operation. Keep
gasoline and any other flammable liquids
away from the heater.
WARNING
Lighting Instructions:
1. STOP! Read all of the safety information
provided with this heater.
2. Turn valve on propane cylinder
COUNTERCLOCKWISE until fully open.
3. Wait ve (5) minutes for any gas to clear. Smell
for gas. If none is evident, proceed to the next
step.
4. Push in the valve knob and turn to "PILOT".
NOTE: If this is rst time use for heater or LP
cylinder has been replaced, hold the valve knob for
approximately 30 seconds to allow bleeding of air
from system then turn valve knob to PILOT.
5. While depressing the valve knob, press
red piezo ignition button to ignite. It may be
necessary to press the igniter button several
times to ignite the center burner panel.
6. Continue to hold valve knob down for 30
seconds after the panel has lit. This will heat
the thermocouple. After 30 seconds, release
the valve knob.
7. If heater fails to light, or does not stay lit, repeat
steps 2 through 6.
8. When the center burner panel stays lit, turn the
valve knob to the desired setting.
Shut Down Instructions
1. Turn valve knob to the OFF position.
2. Turn the knob at the LP cylinder CLOCKWISE
to the OFF position.
3. Disconnect regulator hose assembly from the
LP cylinder.

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Test Firing Heater
It is always a good idea to test re your heater in a safe
and controlled environment, in an area with adequate
ventilation, and away from any combustibles to be sure
that all functions of the heater and gas supply system
are operating properly.
Leak test all gas connections with a 50/50 solution of
dish soap and water. DO NOT use a ame to test for
leaks!
Moving and Positioning the Heater
There is a brake in each of the front wheels of your
heater that helps keep it in place when in use. To
engage the brakes, push the lever down on each
wheel. To move the heater, release the brakes, simply
by ipping the levers on both brakes up.
Operation
7
Ventilation
–Risk of indoor air pollution and Carbon
Monoxide Poisoning. Use heater only in
well ventilated areas.
–Refer to Safety Information on pages 1-2
for information about Carbon Monoxide
Poisoning.
–ALWAYS provide a fresh air opening in the
heated space of at least 3 square feet (2,800
sq. cm) for each 100,000 BTU / Hr. of heater
output. Provide a larger opening if more
heaters are being used.
– FOR OUTDOOR USE. INDOOR USE
PERMITTED ONLY FOR: The temporary
heating of adequately ventilated buildings or
structures under construction, alteration or
repair.
Minimum Ventilation
Opening Needed
18-PCH-O
0.54 ft.2
16.5 cm2
CARBON MONOXIDE POISONING MAY LEAD TO DEATH!
Not for use in
residential living
areas or in
non-adequately ventilated enclosed
spaces.
DANGER
DANGER

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Storage / Maintenance
Always disconnect the LP cylinder from the
regulator assembly and remove the LP cylinder
from the heater before putting the heater
into storage. If, for any reason, the heater is
to be stored indoors, the heater MUST be
disconnected from the LP cylinder, and the
cylinder stored outdoors in a well-ventilated area,
out of the reach of children, and in accordance
with the Standard for Storage and Handling of
Liquefied Gasses, ANSI/NFPA 58 - latest edition.
The plastic valve plug or valve cover supplied
with the LP cylinder must be reinstalled on the
valve to protect the fitting from damage.
NOTE: Repair of this heater should be done
by a qualified service person.
It is recommended that you save all of the
packaging materials that came with your heater,
and re-package the heater using these materials
for safe storage.
Debris, dust and dirt inside of the heater body
can affect the performance of your heater. This
debris can impair the heaters ability to draw air
for ventilation and combustion. Spiderwebs can
also appear during periods of inactivity.
Be sure to inspect the heater before each use to
look for any such obstructions. Be sure to keep
the air passage-ways, burner and combustion
areas clean. Wipe with a damp cloth or use
a vacuum cleaner to clean these areas. It is
suggested that you perform a thorough cleaning
at least once every 30 days of operation. You
may need to clean the heater more often if
conditions are naturally dirty.
Clean the ceramic plaques using compressed air
below 30 PSI to prevent damage to plaques.
A yellow tip of the pilot flame indicates that the
burner area may be in need of cleaning.
Never store an LP cylinder inside of a building or near any other
gas or oil burning appliances.
Always be sure that the heater has been allowed to cool for at least
30 minutes before attempting to store, service, or perform
maintenance.
8
CAUTION
DANGER

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
Problem Possible Cause Solution
Burner fails to ignite
1. Air in gas line
2. Gas pressure from cylinder
too low.
3. LP cylinder valve turned off
4. Obstruction in air
passageway.
5. Dirt in pilot orifice.
6. Safety switch in cylinder
valve engaged.
7. Tipover switch engaged.
1. Keep depressing the gas control
knob for at least 30 seconds to
remove any in line.
2. Check LP cylinder pressure.
Tank may be empty.
3. Open LP cylinder valve.
4. Inspect and clean heater
housing.
5. Blow out, or clean pilot orifice.
6. Close LP cylinder valve. Wait
1 min. for switch to click off.
Reopen LP cylinder valve slowly.
7. Move heater to a level surface.
No spark created when
ignited
1. Incorrect igniter electrode
position.
2. Electrode damaged or
broken.
3. Loose or disconnected
igniter wire.
4. Broken igniter wire.
1. Properly position electrode
2. Replace the electrode.
3. Tighten or reconnect loose wire.
4. Replace igniter wire.
Heater stops running by
itself
1. Thermocouple damaged
2. Gas control valve damaged.
3. Gas leak
4. Thermocouple not in contact
with pilot flame.
5. Tip-over switch damaged,
or loose connection at tip-
switch.
6. Out of fuel.
1. Replace thermocouple.
2. Replace gas control valve.
3. Check all connections for leaks
using 50/50 solution of dish soap
and water. Repair any leaks
found.
4. Clean inside of heater housing.
5. Inspect tip-over switch and
connections. Replace if
necessary.
6. Replace LP cylinder
Troubleshooting Guide
Locating Your Serial Number:
Your serial number can be found on the heater’s rating label. It will begin with the letters PGCV
followed by 8 digits. For Example: PGCV12345678. Have your Serial Number ready before calling
customer service at 866-676-1989.

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
12
3
Exploded View
9
Parts List
Item
#Description 18-PCH-O
1 Front Castor 50-011-0110
2 Rear Castor 50-011-0210
3 Piezo Button 50-014-0100

NEVER LEAVE HEATER UNATTENDED WHILE BURNING, CONNECTED
TO A POWER SOURCE, OR WHILE CONNECTED TO A FUEL SOURCE
© 2017, Pinnacle Climate Technologies, Inc. Cabinet Heater User's Manual
LIMITED WARRANTY
Pinnacle Climate Technologies, Inc. warrants this heater
to the original retail purchaser only, to be free from defects
in material and workmanship for a period of one (1) year
from the date of initial purchase. This product must be
properly installed, maintained and operated in accordance
with the instructions provided.
Pinnacle Climate Technologies, Inc. requires reasonable
proof of your date of purchase from an authorized retailer
or distributor. Therefore, you should keep your sales slip,
invoice or cancelled check from the original purchase.
This Limited Warranty shall be limited to the repair or
replacement of parts, which prove defective under normal
use and service within the warranty period, and which
Pinnacle Climate Technologies , Inc. shall determine at
its reasonable discretion.
This warranty does not apply to products purchased for
rental use.
This Limited Warranty does not cover any failures or
operating difculties due to normal wear and tear, accident,
abuse, misuse, alteration, misapplication, improper
installation or improper maintenance and service by you
or any third party. Failure to perform normal and routine
maintenance on the heater, shipping damage, damage
related to insects, birds or animals of any kind, and damage
due to weather conditions are also not covered.
In addition, the Limited Warranty does not cover damage
to the nish, such as scratches, dents, discoloration, rust or
other weather damage, after purchase.
All transportation costs for the return of damaged product
or parts will be the responsibility of the purchaser. Upon
receipt of damaged item, Pinnacle Climate Technologies,
Inc. will examine the item and determine if defective.
Pinnacle Climate Technologies, Inc. will repair or replace
and return the item, freight pre-paid.
If Pinnacle Climate Technologies, Inc. nds the item to
be in normal operating condition, or not defective the item
will be returned freight collect. This Limited Warranty is
in lieu of all other express warranties. Pinnacle Climate
Technologies, Inc. disclaims al warranties for products
that are purchased from sellers other than authorized
dealers or distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS
WARRANTY EXPIRES, Pinnacle Climate Technologies,
Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
APPLICATION. FURTHER, Pinnacle Climate Technologies,
Inc. SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER
OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE
INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle
Climate Technologies, Inc. assumes no responsibility for
any defects caused by third parties. This Limited Warranty
gives the purchaser specic legal rights; a purchaser may
have other rights depending upon where he or she lives.
Some states do not allow the exclusion or limitation of
special, incidental or consequential damages, or limitations
on how long a warranty lasts, so the above exclusion and
limitations may not apply to you.
Pinnacle Climate Technologies, Inc. does not authorize
any person or company to assume for it any other
obligation or liability in connection with the sale, installation,
use, removal, return or replacement of its equipment, and
no such representations are binding on Pinnacle Climate
Technologies, Inc.
Always be sure to specify the model number and serial
number when making any claim with Pinnacle Climate
Technologies, Inc. For your convenience, use the space
provided below to list this information.
Model #:________________________________
Serial #:________________________________
Date of Purchase: ________________________
Locating Your Serial Number:
Your serial number can be found on the heater’s rating label. It will begin with the letters PGCV followed by 8
digits. For Example: PGCV12345678. Have your Serial Number ready before calling customer service
at 866-676-1989.
10