Pitney Bowes Datamax w1110 User manual

Right, let’s get your Network
Printer up and running quickly…
Let’s rst get together the things you will need:
• The box containing your Network Printer.
• A PC on which you have full admin rights to allow downloading
and installing software.
Continue reading below
Stand-Alone Network Printer
Read Now BEFORE you unpack your equipment
Microsoft Windows Installation Instruction
Network Printer Connection

1. Opening the box and unpacking.
Printer
USB
(not used
for network
installation)
Power CordNetwork Cable
Here’s a diagram and explanation of the items you should
nd in your box.
If you have any problems during this installation, refer to
‘Troubleshooting’.
2. Connecting the printer.
Connect your Network cable to your printer and Network
socket.
Connect the power cord and adapter to your printer
(as shown) and switch on.
Network Cable
Power Cable

3. Printer ready.
4. Aligning the label roll.
Wait for approximately 45 seconds until the green
light remains constant and the printer is ready.
Press the button and check that the label feeds out correctly.
Note: If the label does not feed correctly please refer to label
alignment instructions inside the printer top cover.
Tear o the correctly dispensed label.
Print the System Report to obtain the IP address assigned to
the label printer.
1. To print the system report simultaneously press the
button on the front of the label printer and the recessed
button on the back of the printer with a suitable object
such as a pencil or similar.
2. Keep the printed report that will be needed later in the
installation process.
5. Printing a system report.
System Report
...
Ethernet IP
Ethernet MAC
Ethernet DHCP
Hostname

7. Connecting to the printer.
Select Network and press Next.
Then select Datamax-O’Neil w1110 Printer model when
prompted and select Next.
6. Downloading the printer driver.
1. Go to support.pb.com/workstation
2. Select Download Drivers for Workstation w1110 Label
Printer in the Downloads section.
3. Select in the Download your Windows printer
driver section.
4. Select Run or Open dependant on your browser.
5. Accept the licence agreement and follow the on screen
prompts to install.
8. Specifying a port.
Select Create Port.
Then Select TCP/IP Port and click New Port.

10. Conrming the port.
The wizard will return to the Specify Port screen.
Use the vertical scroll bar to view and conrm the new port is
now in the list and select Next.
9. Printer port wizard.
Select Next to run the Printer Port Wizard.
Enter the Ethernet IP from the system report printed in step 5
and Select Next.
Note: The Port Name will automatically be populated with a
default value.
Windows Wizard will automatically nd the device.
If not found, Select Generic Network Card from the drop
down menu and Select Next.
Select Finish to complete the Printer Port Wizard and to
return to driver installation.
Note: The driver and port name will now show what was
entered in the screen above.
Select Close.
11. Accepting the printer name.
Select Next to accept the default printer name.

13. Test print.
Your SendKit is now connected.
To test your printer is working correctly follow the steps
below.
On a PC
Go to your Control Panel
Select Devices & Printers
Double click on the Printer
(DataMax-O’Neil w1110)
1. Select Printer from the menu bar
2. Select Properties
3. Select General
4. Select Print Test Page.
Check that your label has printed correctly. If you have any
issues with the print refer to Troubleshooting later in this
document.
12. Completing printer setup.
Select Finish to complete the wizard and begin using your
printer.
*AW32662reva*
3001 Summer St.
Stamford, CT 06926
www.pitneybowes.com
AW32662 Rev. A 05/18
©2018 Pitney Bowes Inc.
All Rights Reserved
If you’re still having trouble, then visit
support.pb.com/workstation
and select Errors & Troubleshooting.