Planet POE-E304 User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET 1-port Ultra PoE+ to 4-port IEEE
802.3af/at Gigabit PoE Extender, POE-E304. “Gigabit PoE Extender”
mentioned in this manual refers to the POE-E304.
Open the box of the Gigabit PoE Extender and carefully unpack it. The
box should contain the following items:
Gigabit PoE Extender x 1 User’s Manual x 1
Rubber Feet x 4 Wall-mount Kit
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
Features Store-and-Forward mode with wire-speed ltering and
forwarding rates
IEEE 802.3x ow control for full duplex operation and backpressure
for half duplex operation
Automatic address learning and address aging
Case and Installation
No external power cable installation required
Made of metal, desktop size design
Wall-mountable, Plug-and-Play installation
0 ~ 50 degrees C operating Temperature
Note
PSE (Power Sourcing Equipment) is a device (switch
or hub for instance) that will provide power in a PoE
setup. The maximum allowed continuous output power
per such device in IEEE 802.3af is 15.4 watts and in IEEE
802.3at is 30 watts.
PD (Powered Device) such as IP phones, network
cameras or wireless access points is a PoE-enabled
terminal that consumes energy supplied by PSE.
4. Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Gigabit PoE Extender consists of one
auto-sensing 10/100/1000BASE-T Ultra PoE In port, and four auto-
sensing 10/100/1000BASE-T 802.3af/802.3at PoE Out ports. The LED
Indicators are also located on the port of Gigabit PoE Extender front
panel.
50~56V DC
PoE Extender
PoE In-Use
PoE MAX
PWR
1 2 3 4
541 2
PoE OUT PoE IN
3
POE-E304
10/100
1000
LNK ACT
Figure 1: POE-E304
Protection ESD (Ethernet): 6KV
Surge (EFT for power): 2KV
Enclosure Metal
Installation Desktop/Wall mountable
Dimensions
(W x D x H) 160 x 92.5 x 28mm
Weight 370g
Power
Requirements
PoE In: IEEE 802.3bt or 4-pair 802.3at PoE+
compliant with voltage within 50V-56V DC
External DC: 50~56V DC
Power
Consumption
4 watts/13.7BTU (System on with PoE input)
6 watts/20.6BTU (Ethernet full loading without PoE
function)
60 watts/205.9BTU (Full loading with PoE function)
Network Cable
10BASE-T: 4-pair UTP Cat5 up to 100m (328ft)
100BASE-TX: 4-pair UTP Cat5 up to 100m (328ft)
1000BASE-T: 4-pair UTP Cat5e, 6, up to 100m
(328ft)
EIA/TIA-568 100-ohm STP (100m, 328ft)
Power over Ethernet
PoE Standard
PoE In Port
Ultra Power over Ethernet end-span/mid-span PD
class 4 PD
Per PoE Out Port
IEEE 802.3at Power over Ethernet Plus end-span
PSE
IEEE 802.3af Power over Ethernet end-span PSE
2. Product Features
Physical Port
5-port 10/100/1000BASE-T Gigabit RJ45 interface
- 1-port data + power input
- 4-port data + power output
Power over Ethernet
1-port data + power input
- Complies with Ultra Power over Ethernet end-span/mid-span PD
- Supports PoE input power up to 60 watts
4-port data + power output
- Complies with IEEE 802.3af/IEEE 802.3at Power over Ethernet/
end-span PSE
- Up to 4 IEEE 802.3af/802.3at devices powered
- Supports PoE power up to 30.8 watts for each PoE port
- Auto detects powered device (PD)
Extends the range of PoE to an additional 100 meters (328ft.)
Forwards both Ethernet data and PoE power to remote device
Layer 2 Features
Hardware based 10/100/1000Mbps auto-negotiation and auto MDI/
MDI-X
Integrates address look-up engine, supporting 2K absolute MAC
addresses
9K Jumbo packet support
IEEE 802.1Q VLAN transparency
PoE Power
PoE In Port
50~56V DC, max. 60 watts
Per PoE Out Port
44~55V DC, max. 30.8 watts
Power Pin
Assignment
PoE In Port
1/2 (+), 3/6 (-); 4/5 (+), 7/8 (-) or 1/2(-), 3/6(+);
4/5(+), 7/8(-)
Per PoE Out Port
1/2 (+), 3/6 (-), end-span (Type A)
PoE Power
Budget
50 watts (max.) @ Ultra PoE input
20 watts (max.) @ IEEE 802.3at PoE+ input
Standard Conformance
Regulatory
Compliance FCC Part 15 Class A, CE
Standard
Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3x Flow Control
Environment
Operating Temperature: 0 ~ 50 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Storage Temperature: -10 ~ 70 degrees C
Relative Humidity: 5 ~ 95% (non-condensing)
Note
The maximum distance that data and power can transmit
depends on the quality of the UTP cable and environment.
4.2 Ports Connection
PoE IN Port
Connect the PoE IN port from the following Ultra PSE
devices through a Cat5/5e/6 UTP cable:
Ultra PoE injector
Ultra PoE injector hub
Ultra PoE Ethernet switch
PoE OUT Port
Connect the PoE OUT port to the following 802.3at/af
PD devices through a Cat5/5e/6 UTP cable:
PoE IP camera
PoE VoIP phone
PoE wireless AP
PoE splitter
4.3 LED Indicators
Ultra PoE IN Port
LED Color Function
10/100 LNK/
ACT Orange
Lights to indicate the link through that port is
successfully established at 1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
1000
LNK/ACT Green
Lights to indicate the link through that port is
successfully established at 1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
3.ProductSpecications
Model POE-E304
Hardware Specications
Network
Connector
PoE In Port
1 x 10/100/1000BASE-T Ethernet with Ultra PoE
b in, auto MDI/MDI-X, auto-negotiation RJ45
connector
PoE Out Port
4 x 10/100/1000BASE-T Ethernet with IEEE
802.3at/802.3af PoE “Data + DC” out, auto MDI/
MDI-X, auto-negotiation RJ45 connector
Data Rate 10/100/1000Mbps
Switch
Architecture Store-and-Forward
MAC Address
Table 2K
Data Buffer 2Mbits
Switch Fabric 10Gbps
Switch
Throughput 7.44Mpps @ 64 bytes
Jumbo Frame 9K
Flow Control IEEE 802.3x pause frame for full duplex
Back pressure for half duplex
LED Indicators
PoE In Port
10/100 LNK/ACT (orange), 1000 LNK/ACT (green)
PoE Out Port 1 to Port 4
10/100 LNK/ACT (orange), 1000 LNK/ACT (green)
PoE-in-Use (orange)
PoE Max. (orange)

- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
802.3at/af PoE Out Ports
LED Color Function
10/100
LNK/ACT Orange
Lights to indicate the link through that port is
successfully established at 1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
1000
LNK/ACT Green
Lights to indicate the link through that port is
successfully established at 1000Mbps.
Blinks to indicate that the port is actively
sending or receiving data.
PoE-in-Use
LED Color Function
PoE Max. Orange Lights to indicate the power usage is ≥ 45W
Blinks to indicate the power usage is ≥ 55W
PoE-in-Use Orange Lights to indicate the port is providing 50V-56V
DC in-line power output
5. Hardware Installation
5.1 Before Installation
The POE-E304 is installed between the PSE (Power Source Equipment)
and the PD (powered device); it is powered by PSE and forwards the
Ethernet data and remaining POE power or an external power supply
to the PD and it can be installed easily by just plug and play without
affecting the data transmission performance.
Note
1. When the PoE-in-use LED turns steady orange,
it means the Gigabit PoE OUT is supplying power
successfully from PSE.
2. If the PoE-in-use LED is not lit, please check the
remote PSE or the cable connecting to a PC or a
network device to see if the cable is correct.
Never connect any non-standard POE PSE to the Gigabit
PoE Extender; it will damage the device permanently.
5.3 Connecting POE-E304 to Powered Device (PD)
Step 1: Connect the additional Cat5e/6 cable that will be used to
connect to the remote Powered Device (PD) to the “PoE
Out” port of the Gigabit PoE Extender.
Ultra PoE Switch
PoE Wireless AP
UTP
UTP
PoE Camera
UTP
PoE
PoE
PoE
PoE Extender
PoE In-Use
PoE MAX
PWR
1 2 3 4
541 2
PoE OUT PoE IN
3
POE-E304
10/100
1000
LNK ACT
Step 2: The "PoE Out" port is also the power injector which transmits
DC voltage to the Cat5e/6 cable and transfer data and power
simultaneously between the PSE and PD.
Note
1. To provide you with better PoE power and data
extension quality, we strongly recommend that you use
“Solid UTP Cable” when installing the POE-304.
2. The POE-E304 can be installed with a third-party device
if the device complies with IEEE 802.3at/af standard.
5.2 Connecting POE-E304 to PSE
This section describes how to install Gigabit PoE Extender and make
connection to it. Please read the following topics and perform the
procedures in the order being presented.
There are 4 RJ45 ports in the Gigabit PoE Extender, of which the “PoE
IN” port functions as "PoE (Data and Power) input" and the four
”PoE Out” ports function as "PoE (Data and Power) output".
Step 1: Connect a standard Cat5e/6 UTP cable from power source
equipment (PSE), such as PoE switch, PoE injector hub and
single port PoE injector, to the “PoE IN” port of the Gigabit
PoE Extender.
Ultra PoE Switch
UTP
PoE
PoE Extender
PoE In-Use
PoE MAX
PWR
1 2 3 4
541 2
PoE OUT PoE IN
3
POE-E304
10/100
1000
LNK ACT
Step 2: The PSE delivers both Ethernet data and PoE power over UTP
cable to the Gigabit PoE Extender.
Step 3: Once the Gigabit PoE Extender detects the existence of an
IEEE 802.3at/af device, the “PoE-in-Use” LED indicator will
be lit steadily, showing it is providing powerr.
Note
1. If the connected device is not fully complying with IEEE
802.3af/at standard or in-line power device, the PoE-in-
Use LED indicator of the Gigabit PoE Extender will not
be lit steadily.
2. According to IEEE 802.3af/at standard, the Gigabit
PoE Extender will not inject power to the cable if not
connected to a standard IEEE 802.3af/at device.
5.4 PoE Power Distribution
The POE-E304 can obtain a maximum of 60-watt PoE power from Ultra
PoE input port and supplies a maximum of 55-watt PoE power budget
to four PoE output ports, extending both the reach of Gigabit Ethernet
Data and IEEE 802.3at/802.3af Power over Ethernet over the
standard 100m (328 ft.) Cat 5/5e/6 UTP cable to up to 200m at the
same time.
IEEE 802.3at (25W) IEEE 802.3at (25W)
PoE PTZ IP Camera
IEEE 802.3af (12W) IEEE 802.3af (12W) IEEE 802.3af (12W) IEEE 802.3af (12W)
PoE Dome IP Camera
Ultra PoE (60W) Ultra PoE (60W)
Power
Data
Power
Data
1 In 2 Out 1 In 4 Out
6. Power Over Ethernet Budget
The following table lists how many PoE devices can be powered by
POE-E304:
Power Source PoE Output
Budget* Max. Number of PDs supported
IEEE 802.3at PoE+
PSE 25 watts max.
Class 4 PD@25-watt 1 unit
Class 3 PD@15-watt 1 unit
Class 2 PD@7-watt 3 units
PLANET 60W Ultra
PoE PSE 55 watts max.
Class 4 PD@25-watt 2 units
Class 3 PD@15-watt 3 units
Class 2 PD@7-watt 4 units
External Power
Adapter –
56V DC, 65W
55 watts max.
Class 4 PD@25-watt 2 units
Class 3 PD@15-watt 3 units
Class 2 PD@7-watt 4 units
Note
1. The PoE Output Budget means the 4-port PD
aggregated power output. The aggregated power
consumption will be below 55 watts if with ultra PoE
PSE.
2. If the PoE output, whose power source is IEEE
802.3at PoE+, is more than 25 watts, the device will
be shut down.
7. Customer Support
Thank you for purchasing PLANET products. You can browse our online
FAQ resource at PLANET web site rst to check if it could solve your
issue. If you need more support information, please contact PLANET
switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]
Copyright ©PLANET Technology Corp. 2016.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks
belong to their respective owners