Planet LRE-101C User manual

1-Port 10/100TX over Coaxial
Long Reach Ethernet Extender
LRE-101C
User’s Manual

Trademarks
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in
all environments and applications, and makes no warranty and representation,
either implied or expressed, with respect to the quality, performance,
merchantability, or tness for a particular purpose.
PLANET has made every eort to ensure that this User’s Manual is accurate;
PLANET disclaims liability for any inaccuracies or omissions that may have
occurred.
Information in this User’s Manual is subject to change without notice and
does not represent a commitment on the part of PLANET. PLANET assumes no
responsibility for any inaccuracies that may be contained in this User’s Manual.
PLANET makes no commitment to update or keep current the information in
this User’s Manual, and reserves the right to make improvements to this User’s
Manual and/or to the products described in this User’s Manual, at any time
without notice.
If you nd information in this manual that is incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Statement
NOTE: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

ISEDC Statement
CAN ICES-003(A) / NMB-003(A)
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisee aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioelectrique subi,
meme si le brouillage est susceptible d'en compromettre le fonctionnement.
CE Mark Warning
This device is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
Energy Saving Note of the Device
This power required device does not support Standby mode operation. For
energy saving, please remove the power cable to disconnect the device from
the power circuit. Without removing power cable, the device will still consume
power from the power source. In view of Saving the Energy and reducing the
unnecessary power consumption, it is strongly suggested to remove the power
connection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential eects on the environment and human health
as a result of the presence of hazardous substances in electrical and
electronic equipment, end users of electrical and electronic equipment
should understand the meaning of the crossed-out wheeled bin
symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Revision
PLANET Gigabit Ethernet over Coaxial Converter User's Manual
Model: LRE-101C
Revision: 1.0 (Sep. 2022)
Part No.: 2350-AA3A30-000

Table of Contents
1. Package Contents................................................................................. 5
2. Hardware Introduction .......................................................................... 6
2.1 Physical Dimensions ....................................................................... 6
2.2 Front View .................................................................................... 7
2.3 Rear View ..................................................................................... 8
2.4 Power Information ......................................................................... 9
3. Product Specications ..........................................................................10
4. Installations ........................................................................................12
4.1 Wall-mount Installation .................................................................12
4.2 Chassis Installation and Rack Mounting...........................................13
4.3 Optional DIN-rail Installation..........................................................14
5. Applications ........................................................................................15
5.1 Point-to-Point Application -- LAN to LAN Connection.........................15
5.2 LRE-101C Point to Multi-point Application (IP surveillance) .................... 16
6. Performance Table ...............................................................................17
7. Troubleshooting...................................................................................18
8. FAQs ..................................................................................................19
9. Customer Support ...............................................................................20

5
1. Package Contents
Thank you for purchasing PLANET LRE-101C 1-Port 10/100TX over Coaxial
Long Reach Ethernet Extender. In the following sections, the term “EoC
Converter” means the LRE-101C.
Open the box of the EoC Converter and carefully unpack it. The box should
contain the following items:
LRE-101C DC 5V/2A Power Adapter
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a need to
return it to us for repair.
5

6
2. Hardware Introduction
2.1 Physical Dimensions
Dimensions (W x D x H): 94 x 70.3 x 26.2mm
26.20
94.00
70.30
46.70
∅7.00
Unit: mm
Long Reach Ethernet 10/100TX over Coaxial Extender
5V DC
Master Slave
Long Reach Ethernet over Coaxial Extender
LRE-101C
LNK/
ACT
PWR
LNK
Master
LAN
10/100TX
Long Reach

7
2.2 Front View
 LRE-101C Front Panel
Long Reach Ethernet over Coaxial Extender
LRE-101C
LNK/
ACT
PWR
LNK
Master
LAN
10/100TX
Long Reach
 10/100TX RJ45 connector
 BNC female connector for Long Reach
 LEDs for power, Ethernet and Long Reach
 LRE-101C LED Indicators
The rich diagnostic LEDs on the front panel can provide the operating status of
individual port and whole system.
System
LED Color Function
PWR Green Lit: Indicates that the EoC Converter has power.
O: Indicates that the EoC Converter has no power.
Long Reach Ethernet interface
LED Color Function
LNK Green
Lit: Indicates that the Long Reach Ethernet link is
established.
O: Indicates that the port is link-down.
10/100BASE-TX Port
LED Color Function
LNK/
ACT Green
Lit: Indicates the link through TP port is successfully
established.
Blink: Indicates the TP port is actively sending or receiving
data.
O: Indicates that the TP port is link-down.

8
DIP Switch Setting
In the PtMP setting, it can be one master and more than one slave with BNC T
connector.
LED Color Function
Master Green Lit: Indicates that the LRE-101C is functioned as a Master.
O: Indicates that the LRE-101C is functioned as a Slave.
2.3 Rear View
 LRE-101C Rear Panel
5V DC
Master Slave
 DIP switch: Master/Slave mode selectable
 DC jack (DC input) for power adapter
 DIP Switch
The EoC Converter provides a selectable 2-position DIP switch. When switching
to “Master”, it supports PtMP, meaning it can be one master and more than
one slave with BNC T connector.
DIP Function
Master The LRE-101C is functioned as a Master.
Slave The LRE-101C is functioned as a Slave.
By default, the 2-position DIP switch is set in the “Master”
position and is operated as “CO”. To operate, slide the DIP 1
switch to the “Slave” position. Just slide it to whatever position
you prefer to fulfill your application requirement.

9
2.4 Power Information
The LRE-101C requires 5V DC, 2A power input, which conforms to the bundled
AC adapter. Should you have the issue of power connection, contact your local
sales representative.
2.5mm
DC Receptacle 2.5mm
+5V for each slot
DC receptacle is 2.5mm wide that conforms to the EoC Converter
2.5mm DC jack’s central post. Do not install any improper unit.
In some areas, installing a surge suppression device may also
help to protect your EoC Converter from being damaged by
unregulated surge or current to the EoC Converter or the power
adapter.

10
3.ProductSpecications
Product LRE-101C
Hardware Specications
LAN Ethernet interface
1 10/100BASE-TX RJ45 Copper port,
auto-negotiation/auto-MDI/MDI-X
Cabling Cat5e UTP or above
Maximum
Distance 100 meters
Maximum
Frame Size 1522 bytes
Long Reach Interface
1 BNC female Ethernet over Coaxial
Cabling
Coaxial cable: 75 ohm
RG-6/U cable, less than 12Ω/1000 ft
RG-59/U cable, less than 30Ω/1000 ft
Maximum
Distance
Max. 2000 with data transmission
(6,561ft.)
Long Reach
Ethernet
Standard
IEEE 1901
Modulation
Type Wavelet-OFDM
Security 128-bit AES encryption
Frequency
Band 2~28MHz
Performance*
Distance Data Rate
(Upstream/Downstream)
200m 94/94Mbps
600m 94/94Mbps
800m 88/87Mbps
1000m 76/73Mbps
1200m 61/58Mbps
1400m 45/43Mbps

11
Long Reach Interface Performance*
1600m 35/33Mbps
1800m 34/23Mbps
2000m 3/8Mbps
Functionality DIP Switch Select Master or Slave mode
Dimensions
(W x D x H) 97 x 70.3 x 26 mm
Weight 194g
Housing Metal
Power Requirement 5V DC, 2A external power
LED Indicators
Power: Green
LAN: Green, 10/100Mbps LNK/ACT
Long Reach: Green, LNK
Master: Green
Standards Conformance
Standards Compliance
IEEE 802.3/802.3u Ethernet standard compliant
IEEE 802.3x Full-duplex ow control
IEEE 802.1q Tag VLAN Transparent, Multicast pass-
through
Regulatory Compliance FCC Part 15 Class A, CE
Environment
Temperature Operating: 0~50 degrees C
Storage: -10~70 degrees C
Humidity Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)
* The actual data rate will vary in the quality of the coaxial cables and
environmental factors.

12
4. Installations
4.1 Wall-mount Installation
Step 1: Find a suitable wall to mount the LRE-101C.
Step 2: Screw two screws on the wall.
Step 3: Hang the LRE-101C on the screws from the wall.
Step 4: Repeat Chapter 2.4 Power Information on power supply to the
LRE-101C.
10GBASE-T to 10GBASE-X
5V DC
Before mounting the device to the wall, please check the loca-
tion of the electrical outlet and the length of the Ethernet cable.

13
4.2 Chassis Installation and Rack Mounting
To install the EoC Converter in a 10-inch or 19-inch Converter Chassis with
standard rack, follow the instructions described below.
Step 1: Place your LRE-101C on a hard at surface, with the front panel
positioned towards your front side.
Step 2: Carefully slide in the module until it is fully and rmly tted into the
slot of the converter chassis.
Step 3: Attach a rack-mount bracket to each side of the Converter Chassis
with supplied screws attached to the package.
Step 4: After the brackets are attached to the Converter Chassis, use
suitable screws to securely attach the brackets to the rack.
Step 5: Proceed with Step 4 and Step 5 of the 4.1 Installation section to
connect the network cabling and supply power to your Converter
Chassis.
You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would
invalidate your warranty.

14
4.3 Optional DIN-rail Installation
There are two DIN-rail holes on the left side of the LRE-101C that allows to
be easily installed by DIN-rail mounting. PLANET optional DIN-rail mounting kit
– RKE-DIN -- can be ordered separately. Refer to the following steps for the
DIN-rail mounting of the LRE-101C:
Step 1: Screw the DIN rail on the LRE-101C.
Step 2: Now slide the DIN rail into the track.
Step 3: Check whether the DIN rail is tightly on the track.
You must use the screws supplied with the mounting brackets.
Damage caused to the parts by using incorrect screws would
invalidate your warranty.

15
5. Applications
The EoC Converter does not require any software conguration. Users can
immediately use any feature of this product simply by attaching the cables and
turning the power on. There are some key limitations on the EoC Converter.
Please check the following items.
5.1 Point-to-Point Application -- LAN to LAN Connection
One set of the EoC Converter could be used to link two local area networks
that are located in dierent places. Through the coaxial cable, it could set up
a 100Mbps backbone, but one EoC Converter must be Master (CO mode) and
the other one is Slave (CPE mode).
Point to Point Application
Up to 2000m
Ethernet over Coaxial
5V DC adapter
Switch
PC
LRE-101C
Master
LRE-101C
Slave
5V DC adapter
Connecting Standalone PC
Refer to the following procedures to set up the LRE-101C LAN to LAN
connection.
1. [LAN1] Set the LRE-101C in LAN 1 to be in the Master mode from the DIP
switch.
2. [LAN2] Set the LRE-101C in LAN 2 to be in the Slave mode from the DIP
switch.
3. Power on the LRE-101C Master and Slave at both sides by connecting its
power source.
4. Master or Slave LED will illuminate correspondingly.
5. Connect coaxial cable from LAN1 LRE-101C to BNC port of the LAN2
LRE-101C.
6. LNK LED will blink to illuminate at both LRE-101C units.
7. Connect the LRE-101C Ethernet LAN port to other network device via
regular Cat5e UTP cable.

16
5.2 LRE-101C Point to Multi-point Application (IP surveillance)
Video
LRE-101C
Master
LRE-101C
Slave
5V DC adapter
Switch
Monitor
NVR
IP Camera
LRE-101C
Slave
5V DC adapter
5V DC adapter
IP Camera
BNC Tee Connector
100m100m 1600m
100BASE-TX UTP
Video Line
Video
Coaxial Cable
Coax.
Coax.
Coax.
Coax.
Building an IP surveillance system
Refer to the following procedure to set up an IP surveillance system with many
pairs of the LRE-101C:
1.Set the LRE-101C to be in the Master or Slave mode from the DIP switch on
the rear panel.
2. Power on the LRE-101C by connecting its power source.
3. Power LED will illuminate.
4. Connect coaxial cable to the Long Reach ports of two LRE-101C units.
5. LNK LED will illuminate and blink.
6. Connect Ethernet port to IP cameras via regular Cat. 5, 5e or 6 cable.
7. Install the NVR and monitor and connect to one Ethernet switch.
8. You can get data transmissions from all IP cameras.

17
6. Performance Table
 LRE-101C Upstream/Downstream Performance
Coaxial
Distance (meter)
(Upstream/Downstream)
Unit: Mbps
200 94 94
500 94 94
600 94 94
800 88 87
1000 76 73
1200 61 58
1400 45 43
1600 35 33
1800 34 23
2000 3 8
*** The actual data rate will vary in the quality of the coaxial cables and
environmental factors.

18
7. Troubleshooting
SYMPTOM:
LNK LED does not light up after wire is connected to the Long Reach port.
CHECKPOINT:
Please note you must use one LRE-101C in Master mode and the other
LRE-101C in Slave mode to make connection to each other work
SYMPTOM:
TP LED does not light after cable is connected to the port.
CHECKPOINT:
1. Verify you are using the Cat5e or better cable with RJ45 connector to
connect to the port.
2. If your device (like LAN card) supports auto-negotiation, please try to manu-
ally set at a xed speed of your device to solve this issue.
3. The LRE-101C and the connected device’s power are on or not.
4. The port’s cable is rmly seated in its connectors in the switch and in the
associated device.
5. The connecting cable is good and with the correct type.
6. The connecting device, including any network adapter, is functional.

19
8. FAQs
Q1: What is the best distance for LRE-101C?
A1: In order to guarantee the stability and better quality of network, we
suggest the distance should not exceed 700m (Cat.5 UTP) and 1200m
(Phone wire).

20
9. Customer Support
Thank you for purchasing PLANET products. You can browse our online FAQ
resource and User’s Manual on PLANET Web site rst to check if it could solve
your issue. If you need more support information, please contact PLANET
switch support team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.