Planet IPOE-171S User manual

Industrial Ultra Power over Ethernet Splitter
IPOE-171S
User’s Manual

Table of Contents
1. Package Contents ............................................................. 3
2. Product Features............................................................... 4
3.ProductSpecications ....................................................... 5
4. Hardware Introduction ...................................................... 8
4.1 Three-View Diagram ................................................ 8
4.2 Product Front Panel ................................................. 9
4.3 LED Indicators ...................................................... 10
5. Hardware Installation ...................................................... 11
5.1 Before Installation ................................................. 11
5.2 4-pin Power Output Terminal Block ......................... 12
5.3 Wiring the Power Outputs ...................................... 13
6. Customer Support .......................................................... 16

33
1.Package Contents
Thank you for purchasing PLANET Industrial Ultra Power over
Ethernet Splitter, IPOE-171S. “Ultra PoE Splitter” mentioned
in this manual refers to the IPOE-171S.
Open the box of the Ultra PoE Splitter and carefully unpack it.
The box should contain the following items:
Ultra PoE Splitter x 1 User’s Manual x 1
DIN Rail Kit Wall-mount Kit
If any of these are missing or damaged, please contact your
dealer immediately; if possible, retain the carton including the
original packing material, and use them again to repack the
product in case there is a need to return it to us for repair.

4
2.Product Features
Interface
z2-Port RJ45 interfaces
1-Port Data + Power input
1-Port Data output
z2 DC output (4-pin terminal block)
z1 DC 12V/24V DIP switch
Power over Ethernet
zComplies with ultra Power over Ethernet end-span and mid-
span PDs
zComplies with IEEE 802.3at Power over Ethernet Plus end-
span/mid-span PD
zSupports PoE input power up to 75 watts
zSplits the 50~56V DC power over RJ45 Ethernet cable into
DC 12V/24V output
zRemote power feeding up to 100 meters
Hardware
zIP30 metal case protection
zDIN rail and wall-mount design
z-40 to 75 degrees C operating temperature
Note
PSE (Power Sourcing Equipment) is a device
(switch or hub for instance) that will provide
power in a PoE setup. The maximum allowed
continuous output power per such device in IEEE
802.3af is 15.4 watts, in IEEE 802.3at is 30 watts
and in IEEE 802.3bt is 60 watts to 100watts.
PD (Powered Device) such as IP phones,
network cameras, wireless access points, PoE
extender or PoE splitters, is a PoE-enabled
terminal that consumes energy supplied by PSE.

5
3.ProductSpecications
Product IPOE-171S
HardwareSpecications
Interface
PoE Input
Port
1 10/100/1000 BASE-T RJ45
“PoE (Data + Power) In”
Data Output
Port
1 10/100/1000 BASE-T RJ45
“Data Out”
DC Out Plug
Connector 1 removable 4-pin terminal block
DIP Switch 12V DC/24V DC output voltage
LED
Indicator
Power Ready Green
802.3at
PoE+ In Green
Ultra PoE
or 802.3bt
PoE in
Green
DC 12V Green
DC 24V Orange
Network
Cable
Ultra PoE
(60W/75W)
4-pair UTP Cat5e, 6, up to 100m
(328ft)
802.3at
PoE+
2-pair UTP Cat. 3, 4, 5, up to 100m
(328ft)
Data Rate 10/100/1000Mbps
Dimensions
(W x D x H) 32 x 87 x 135 mm
Weight 425g

6
Installation DIN rail/wall mountable
Enclosure IP30 metal case
Power Requirements 50 ~ 56V DC PoE
Power Output
(at 56V DC Input)
12V DC, 4.5A (max.)
24V DC, 2.3A (max.)
Power Consumption
System on with PoE
input: 3.7 watts
Ethernet full loading
without DC output: 3.7 watts
Full loading with
maximum 12VDC,
4A output:
60.2 watts
Full loading with
maximum 12VDC,
4.5A output:
75 watts
(75W PoE in)
Power over Ethernet
PoE Standard
Ultra Power over Ethernet, 4-pair
802.3at PoE+ and Cisco UPOE
compliant with voltage within
50V-56V DC
Power Output DC 12V/24V by DIP switch control
PoE Power Supply Type
end-span + mid-span
end-span
mid-span
Power Pin Assignment 1/2 (+), 3/6 (-); 4/5 (+), 7/8 (-) or
1/2(-), 3/6(+); 4/5(+), 7/8(-)

7
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
IEEE 802.3at Power over Ethernet
Plus
IEEE 802.3af Power over Ethernet
Regulatory Compliance FCC Part 15 Class A, CE
Environment
Operating Temperature -40~ 75 degrees C
Storage Temperature -40~ 85 degrees C
Humidity 5 ~ 95% (non-condensing)

8
4.Hardware Introduction
4.1 Three-View Diagram
The three-view diagram of the Ultra PoE Splitter consists of
one auto-sensing 10/100/1000BASE-T Ultra PoE In port, one
auto-sensing 10/100/1000BASE-T Data Out port and one
removable 4-pin terminal block. The LED Indicators are also
located on the port of Ultra PoE Splitter front panel.
Dimensions ( unit = mm )
Side View
Bottom View Front View
Mounting Kit
Mounting Kit
DIN-Rail Kit
Top View Rear View
PoE IN
10/100/1000T
10/100/1000T
Power Output
Data Out
12V
12V 24V
DC Voltage
24V
PWR 30W 60W
V+
V+
V
V
Industrial Ultra PoE Splitter
PoE Input
Figure 1: IPOE-171S Three-View Diagram

9
4.2 Product Front Panel
PoE IN
10/100/1000T
10/100/1000T
Power Output
Data Out
12V
12V 24V
DC Voltage
24V
PWR 30W 60W
V+
V+
V
V
Industrial Ultra PoE Splitter
PoE Input
Figure 2: Front Panel of IPOE-171S

10
4.3 LED Indicators
PWR
LED Color Function
Power Ready Green
Lights to indicate the port is
receiving 50~57V DC in-line power
and ready for output
30W Green
Lights to indicate the ultra PoE
splitter is working on 802.3at PoE
mode
60W Green
Lights to indicate the ultra PoE
splitter is working on Ultra PoE or
802.3bt PoE in
DC Output voltage indicator
LED Color Function
12V Green Lights to indicate the ultra PoE splitter’s
output is in 12V DC mode
24V Orange Lights to indicate the ultra PoE splitter’s
output is in 24V DC mode

11
5.Hardware Installation
5.1 Before Installation
If there is no power socket in your network environment,
the IPOE-171S provides DC power for this Ethernet Device
conveniently and easily. The IPOE-171S will separate the power
and data out. It provides two kinds of DC power output through
its DIP switch and its voltage and current shown below:
Power Output
12V
12V 24V
DC Voltage
24V
V+
V+
V
V
Figure 3: DIP Switch of IPOE-171S
Please check the power requirements of the
device carefully, that is going to get the power
from IPOE-171S.
If the power requirement is higher than the
IPOE-171S can supply, current overload might
shut down the IPOE-171S itself. Thus, it will
also shut down your device as well.
Please ensure the output voltage is correct for
remote device. Otherwise, it will damage your
remote device.

12
Forbid to switch on/off the Power DIP during
operation. Otherwise, it will damage your IPOE-
171S and remote device. If you want to switch
the output Voltage DIP, please Plug OUT the
“POE In” cable and wait for 3 seconds until
the POE LED (Power) is completely OFF.
5.2 4-pin Power Output Terminal Block
From top to down, there are Negative (V-), Negative (V-),
Positive (V+) and Positive (V+), and two sets of DC power
output contact.
Power Output
12V
12V 24V
DC Voltage
24V
V+
V+
V
V
Figure 4: Terminal Block of IPOE-171S
Note
Two DC outputs are sharing 12V 2A or 24V 1A,
totaling 55 watts DC output power, which
means that DC1 + DC2 cannot be over the 55
watts DC output power. Otherwise, it might cause
the power output to malfunction or damage.

13
5.3 Wiring the Power Outputs
Please follow the steps below to insert the power wires.
Step 1: Please nd one terminal block connector within two
DC power outputs shown below:
DC Output 2
DC Output 1
Note
The wire gauge for the terminal block should be in
the range of 12 ~ 24 AWG.
Step 2: Insert the Negative/Positive DC wires into the
V– / V+ terminal; terminals 1 and 3 for Power 1;
terminals 2 and 4 for Power 2.

14
Step 3: Connect the other point of DC power wires to the
power devices. Tighten the wire-clamp screws for
preventing the wires from loosening.
Maximum Output 48 Watts
Powered
Device 1
Total Maximum
Output 48 Watts
Powered
Device
Powered
Device
1
2
Step 4: Install the terminal block on PLANET IPOE-171S
Splitter.

15
Step 5: Connect the network copper cable (RJ45) from the
Ultra PoE PSE and it will provide power to PLANET
IPOE-171S Splitter and it will separate the power
and data to the PDs (power devices). Please see the
gurebelow:
Non-PoE
Device
Ultra
PoE PSE
Ultra PoE Data in
Data Out
DC
-
DC+
10/100/1000T Copper
Please ensure the IPOE-171S output voltage is
correct before applying power to remote device.
The IPOE-171S provides DC 12V/24V power
output.

16
7.Customer Support
Thank you for purchasing PLANET products. You can browse our
online FAQ resource at PLANET web site rst to check if it could
solve your issue. If you need more support information, please
contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2017.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners