Planet VC24024 Operator's manual

VDSL2 IP DSLAM
VC-2402 / VC-2402-48
Quick Installation Guide

Table of Contents
Mandatory Regulations ..................................................................................... 3
Package Contents ............................................................................................ 5
1. Installation of the VC-2402.......................................................................... 6
1.1 Pre-Installation.................................................................................... 6
1.1.1 Tools and Test Equipment Requirements....................................... 6
1.1.2 Safety Requirement.................................................................... 6
1.1.3 Electrostatic Discharge Protection ................................................ 6
1.2 Hardware Installation........................................................................... 7
1.2.1 Hardware Type........................................................................... 7
1.2.2 Installation Overview .................................................................. 7
1.2.3 Mounting the VC-2402................................................................ 8
1.2.4 Power and Ground Connections ..................................................10
1.2.5 Connecting the VDSL/ADSLx and POTS interfaces ........................11
1.2.6 Connecting the GBE1/GBE2 trunk interface..................................13
1.2.7 Ethernet Port (MGMT)................................................................14
1.2.8 Console Port (CID) ....................................................................15
1.2.9 Housekeeping and Alarm Contact Output Interface.......................16
1.3 Provisioning a Management IP port......................................................17
1.4 CongurationImport/Export ................................................................21
1.5 Firmware Update................................................................................23
2. Operating and Maintaining the VC-2402.......................................................25
2.1 Maintenance requirement ....................................................................25
2.1.1 Tools and Equipment Requirements.............................................25
2.1.2 System Spares..........................................................................25

2.1.3 Dispatching Maintenance Personnel.............................................25
2.1.4 Electrostatic Discharge Protection ...............................................25
2.1.5 Routine Maintenance .................................................................25
2.2 Powering the VC-2402 Up or Down ......................................................26
2.3 Controls and LED Indication ................................................................27
2.4 Cleaning Units....................................................................................29
3. Troubleshooting the VC-2402......................................................................30
3.1 Introduction to Troubleshooting............................................................30
3.2 Resolving Problems Indicated Through LEDs .........................................30
3.3 Resolving Problems Indicated Through Alarms.......................................30
3.4 Procedures for Troubleshooting the VC-2402.........................................30

3
Mandatory Regulations
The following sections describe the mandatory regulations that govern the
installation and operation of the VC-2402.
List of Terms
Table 1 lists the terms used in this chapter.
List of Terms
Term Expansion
CE Conformité Européenne
EN European Standards
FCC Federal Communications Commission
ITU-T Telecommunication Standardization Sector of the International
Telecommunications Union
RoHS Restriction of Hazardous Substances
General Requirements
The sections that follow outline the mandatory regulations that govern the
installation and operation of the VC-2402. You must adhere to these instructions so
that your system meets regulatory requirements.
Prevention of Access
The VC-2402 must be accessible only to authorized personnel. Install this apparatus
in a restricted access location or similar environment to prevent unauthorized
access.
Laser Interface
The VC-2402 uses Class I lasers as optical transmitter sources which are inherently
safe unless mishandled. The radiation from laser diodes is much more intense than
other light sources radiation. Only trained operating personnel thoroughly familiar
with laser radiation hazards should install or remove the ber optic cables and
cards in this system.
EMC Compliance
EMC compliance may require the use of ferrites, shielded cables or other special
accessories. Where required, these special accessories must be installed as per the
instructions.

4
Regulations compliance
Safety Approval
The system complies with the following safety norms:
– ProductSafetyRequirementsidentiedinEN60950:2000
– Over Voltage Protection Requirements of ITU-T K.20
EMI/EMC
The system meets the requirements of Telecommunications Network Equipment:
EN300-386.
Electromagnetic Compliance
The system complies with the standard FCC Part 15 Class A and EN55022.
RoHS
The system complies with the RoHS.
CE
The system conforms to the CE requirement.

5
Package Contents
VC-2402 / VC-2402-48
• VC-2402 / VC-2402-48 Unit x 1
• AC / DC Power Cord x 1
• CD (Containing User’s Manual, QIG) x 1
• Quick Installation Guide x 1
• 2-Meter Telco-50 Cable x 2
• Console Cable x 1
• Rack-mounting x 2
• Screw Package x 2
• Connector Tenon x 2
If any of above items are damaged or missing, please contact your dealer
immediately.

6
1. Installation of the VC-2402
1.1 Pre-Installation
This section provides the information users have to ware before installing the VC-
2402. The information includes required installation tools, safety requirements, and
electrostatic discharge protection.
1.1.1 Tools and Test Equipment Requirements
To install and maintain the VC-2402, you should have the tools and test equipment
listed in the Table 1-1.
Table 1-1 Required Installation Tools and Materials
Item Required Purpose
Anti-static wrist strap Protect the VC-2402 system from electrostatic
discharge damage.
Hand tools Screw drivers for equipment removal and
replacement.
Wire cutter/stripper Prepare wires for electrical connections.
Accessories and hardware kit Screws, bolts, etc., for securing the equipment
on the desired location.
1.1.2 Safety Requirement
To prevent possible serious injury, do not apply power to the VC-2402 system at
the central ofce or any remote site until you’ve completed all of the installation
procedures and connected it to the external facilities. Be cautious, when turning
on/off the VC-2402 system power.
1.1.3 Electrostatic Discharge Protection
The terminal cards contain static-sensitive components. When handling them, be
sure to wear a properly grounded anti-static wrist strap to prevent the damage
from electrostatic discharge. If a wrist strap is not available, hold all cards only
by their edges or extractor handles. Do not touch any component or traces on
the cards. For future use, store cards in original shipped antistatic bags, or in an
approved static-protected bag or container.
To minimize the possible damage from electrostatic discharge, do not install the VC-
2402 in cold, dry places where static electricity can build up. Also, when handling
cards, do not touch their rear-edge connector traces. These electrical contact points
should be kept free of body oils and other contaminants.

7
1.2 Hardware Installation
The hardware installation for the VC-2402 is simple and without complex hardware
setting. However, it should be installed following out the standard installation
procedures. During installation, basic safety precaution should always be taken,
especially, be sure to wear an antistatic wrist strap to prevent static electricity from
damaging the system and injury to the operator. Handle electronic components as
little as possible.
This chapter provides the VC-2402 system hardware installation procedures and
install samples for reference. Please perform the procedures in the suggested
order.
1.2.1 Hardware Type
There are two different types of VC-2402 hardware with the front panel view:
VC-2402-48 with DC power and splitter
VC-2402 with AC power and splitter
1.2.2 Installation Overview
The installation consists of the following procedures. Each procedure will be
explained in detail in the following sections:
Step 1: Mount the system into the desired location of a rack.
Step 2: Turn the power switch in OFF position. Connect to the DC power supply,
and then check the voltage. Make sure the power switch is in OFF position
before wiring the power cable and grounding.
Step 3: Connect the cable between system and MDF.
After executing the previous procedures, please check the cable connection
robustness and correctness before turning on the power supply.

8
Step 4: Connect Console cable to COM port of a computer. Then run the terminal
program with the setting shown below:
Console Setting
Users can also access the DSLAM via Ethernet. By default the out-band IP address
of the DSLAM is obtained via DHCP. Users can also set the IP address manually
by using the CLI commands or Web Conguration Tool (refer to section 1.3). It’s
possible to access the DSLAM with telnet on port 23.
1.2.3 Mounting the VC-2402
The position and orientation of the brackets depends on the rack used for
mounting. The DSLAM can be front-mounted in a standard channel rack (5-inch
projection); and it can be shipped with the mounting brackets installed in one of
three mounting positions or shipped loose.
The mounting brackets can be rotated for use in wall mounting. Optional adhesive
feet may be attached to the bottom of the chassis so that it can be placed on a
desk or other smooth surface.
STANDARD
FRONT MOUNT
FRONT
MOUNTING
BRACKET
MOUNTING
BRACKET
Mounting Bracket Orientation (Top View)

9
Afterthesite requirementshave beenveried,thechassismay beinstalledatthe
specied location.  When mounting the chassis, practice good safety habits. Use
two or more people to secure the chassis. Relay rack mounting normally requires
at least two people.
Step Action
1Locate the chassis and obtain the appropriate chassis mounting
hardware.
2Determine and obtain the tools required for the chassis mounting
hardware.
3From the front of the relay rack, position the chassis in its relay rack
mounting location.
4Using the appropriate rack mounting hardware, secure the chassis in its
relay location on both left and right side of mounting bracket.
Note
The chassis should be empty during the chassis mounting proce-
dures. Remove any unit in the chassis, and store them according to
static-sensitive device storage procedures.
Warning
Hazardous voltages may exist on the chassis. Always practice good
safety habits when wiring a live circuit or performing maintenance.
For 23’’ Rack
For 19’’ Rack
Mounting Bracket Position for Standard Mount (VC-2402-48 shown)