Planet GS-5220-8P2T2S User manual

L2+ Managed Gigabit/10 Gigabit Ethernet Switch
NEXT-3032FGL2-SFP
Quick Installation Guide

Table of Contents
1. Package Contents........................................................................................ 3
2. Requirements.................................................................................................. 4
3. Terminal Setup............................................................................................ 5
4. Logon to Console ........................................................................................ 6
5. Configuring IP Address ................................................................................ 7
6. Starting Web Management ........................................................................... 9
7. Saving Configuration ......................................................................................12
8. Recovering Back to Default Configuration........................................................13
9. Customer Support ..................................................................................... 14

3
1. Package Contents
Thank you for purchasing PLANET L2+ Managed Gigabit/10 Gigabit Ethernet
Switch. The description of this model is shown below:
Model Name
Gigabit RJ45
Ports
Gigabit SFP
Slots
PoE Ports
10G SFP+
Slots
GS-5220-8P2T2S
2
2
8
-
GS-5220-16S8C
8 combo
24
-
-
GS-5220-16S8CR
8 combo
24
-
-
GS-5220-44S4C
4 combo
48
-
-
GS-5220-46S2C4X
2 combo
48
-
4
GS-5220-48T4X
48
4 combo
-
4
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed Switch and carefully unpack it. The box should
contain the following items:
z The Managed Switch
z Quick Installation Guide
z RJ45 to RS232 Cable
z Rubber Feet
z Two Rack-mounting Brackets with Attachment Screws
z Power Cord
z SFP Dust-proof Caps
SFP Dust-proof Caps
GS-5220-8P2T2S
2
GS-5220-16S8C(R)
24
GS-5220-44S4C
48
GS-5220-46S2C4X
52
GS-5220-48T4X
8
If any item is found missing or damaged, please contact your local reseller for
replacement.

4
2. Requirements
z Workstations running Windows XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux, UNIX, or other platforms are compatible with TCP/IP protocols.
z Workstations are installed with Ethernet NIC (Network Interface Card)
z Serial Port Connection (Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
Hyper Terminal included in Windows XP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
end to the console port of the Managed Switch.
z Ethernet Port Connection
Network cables -- Use standard network (UTP) cables with RJ45 connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
and then try it again.

5
3. Terminal Setup
To configure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type of serial port of the Managed Switch.
PC / Workstation
with
Terminal Emulation Software
Managed Switch
Figure 3-1 Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2. When the following screen appears, make sure that the COM port should be
configured as:
Baud : 115200
Data bits 8
Parity : None
Stop bits 1
Flow control : None
Figure 3-2: COM Port Configuration
RJ45
Console Port
RS232 to RJ45Cable
Serial Port

6
4. Logon to Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
password are shown as follows and the login screen in Figure 4-1 appears.
Figure 4-1: Managed Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
description of the commands, please refer to the following chapters.
Username: admin
Password: admin
Note
1. For security reason, please change and memorize the new pass-
word after this first setup.
2. Only accept command in lowercase letter under console inter-
face.

7
5. Configuring IP Address
The Managed Switch is shipped with default IP address shown below.
To check the current IP address or modify a new IP address for the Switch, please
use the procedures as follows:
Show the current IP Address
1. At the “#” prompt, enter “show ip interface brief”.
2. The screen displays the current IP address as shown in Figure 5-1.
Figure 5-1: IP Information Screen
Configuring IP Address
3. At the “#” prompt, enter the following command and press <Enter> as shown
in Figure 5-2.
The previous command would apply the following settings for the Managed Switch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Figure 5-2: Configuring IP Address Screen
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
GS-5220 Series# configure terminal
GS-5220 Series(config)# interface vlan 1
GS-5220 Series(config-if-vlan)# ip address 192.168.1.100 255.255.255.0

8
4. Repeat step 1 to check if the IP address is changed.
Store current switch configuration
5. At the “#” prompt, enter the following command and press <Enter>
Figure 5-3: Saving Current Configuration Command Screen
If the IP is successfully configured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
Switch through the new IP address.
# copy running-config startup-config
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.

9
6. Starting Web Management
The following shows how to start up the Web Management of the Managed Switch.
Note the Managed Switch is configured through an Ethernet connection. Please make
sure the manager PC must be set on the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set at 192.168.0.x (where x is a number
between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTPCable
IP Address:
192.168.0.100
Figure 6-1: IP Management Diagram
Logging in the Managed Switch
1. Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100 (the factory default IP address or the one that you have
just changed in console) to access the Web interface.

10
2. When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screen in Figure 6-2 appears.
Figure 6-2: Login Screen
3. After entering the password, the main screen appears as Figure 6-3 shows.
Default Username: admin
Default Password: admin