Planet FSD-504HP User manual

- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Check the following contents of your package:
Fast Ethernet High Power PoE Switch x 1
User's Manual x 1
Power Adapter x 1
Power Cord x 1
Rubber Feet x 4
If any of these are missing or damaged, please contact
your dealer immediately; if possible, retain the carton
including the original packing material, and use them
again to repack the product in case there is a need to
return it to us for repair.
4. LED Indicators
System
LED Color Function
PWR Green Light: Indicates the Switch has
power.
Per 10/100Mbps Port
LED Color Function
PoE Orange
Light: Indicates the port is
providing 48V DC in-line
power.
LNK/ACT Green
Light: Indicates the link
through that port is
successfully established
at 10/100Mbps.
Blink: Indicates that the Switch
is actively sending or
receiving data over that
port.
2. Product Features
RJ-45 Interface
Five 10/100Mbps Fast Ethernet ports
4 ports support 48V DC power to PoE Powered
Device
Power over Ethernet
Complies with IEEE 802.3af / at Power over
Ethernet Mid-Span PSE
Up to 4 IEEE 802.3af / at devices powered
Supports PoE Power up to 30 watts for each PoE
port
60 watts PoE Budget
Auto detects powered device (PD)
Circuit protection prevents power interference
between ports
Remote power feeding up to 100m
Switching
Hardware based 10/100Mbps Auto-Negotiation and
Auto MDI/MDI-X
Flow control for Full Duplex operation and back
pressure for Half Duplex operation
1536Bytes packet size support
Integrates address look-up engine, supporting 1K
absolute MAC addresses
Automatic address learning and address aging
Hardware
Desktop palm size
LED indicators for PoE ready / activity and LINK /
ACT
One DC 48V power jack
5. Switch Rear Panel
Figure 5-1 shows the rear panel of FSD-504HP.
48V DC
135 4 2 Uplink
Figure 5-1: FSD-504HP Rear Panel
Power
Notice
1. The device is a power-required device,
meaning it will not work till it is powered.
If your networks should be active all the
time, please consider using UPS (Uninter-
rupted Power Supply) for your device. It
will prevent you from network data loss
or network downtime.
2. In some area, installing a surge suppres-
sion device may also help to protect your
FSD-504HP from being damaged by un-
regulated surge or current to the FSD-
504HP or the power adapter.
3. Switch Front Panel
Figure 3-1 shows the front panel of FSD-504HP.
PoE
PWR 1 2 3 4 5 FSD-504HP
ACTLNK
5-Port 10/100Mbps
802.3at PoE+ Switch
Figure 3-1: FSD-504HP Front Panel
6. Installing the Switch
This part describes how to install your Fast Ethernet
High Power PoE Switch and make connections to
it. Please read the following topics and follow the
procedures as presented.
Note
This Fast Ethernet High Power PoE Switch
does not need software configuration.
Desktop Installation
To install the Fast Ethernet High Power PoE Switch on
desktop, simply follow the following steps:
Step 1: Attach the rubber feet to the recessed areas
on the bottom of the Fast Ethernet High Power
PoE Switch.
Step 2: Place the Fast Ethernet High Power PoE Switch
on desktop near AC power source for its power
adapter.
Step 3: Keep enough ventilation space between the
Fast Ethernet High Power PoE Switch and the
surrounding objects.
Note
When choosing a location, please keep in
mind the environmental restrictions dis-
cussed in Chapter 7 -- Product Specifica-
tions.
Step 4: Connect your Fast Ethernet High Power PoE
Switch to network devices.
A. Connect one end of a standard network cable to
the 10/100Mbps RJ-45 ports on the back of the
Fast Ethernet High Power PoE Switch.
B. Connect the other end of the cable to the network
devices such as printer servers, workstations or
routers.
Step 5: Connect your Fast Ethernet High Power PoE
Switch to PoE PD devices.
A. Connect one end of a standard network cable to
port 2 to port 4 10/100Mbps RJ-45 ports on the
back of the Fast Ethernet High Power PoE Switch.
B. Connect the other end of the cable to the 802.3at
/ af powered devices.
Office Building
Office Building Office Area
Warehouse
Control Room
Speed Dome
IEEE 802.3af
PoE IP Camera
PoE Extender
IEEE 802.3af PoE
VoIP Phone
IEEE 802.3af
PoE IP Camera
IEEE 802.3at
PoE Splitter
FSD-504HP
DC
PoE
PoE
PoE
PoE
DC Power Line (DC)
100Base-TX UTP
PoE
100Base-TX UTP with PoE

- 9 -
- 10 - - 12 - - 13 -
- 11 -
Note
Cable distance for Switch
The cable distance between the FSD-504HP
and PC / PD devices should not exceed 100
meters for UTP/STP cable.
Note
Make sure the wiring is correct
It can be used Category 3/4/5 cable in 10
Mbps operation. To reliably operate your
network at 100Mbps, you must use an Un-
shielded Twisted-Pair (UTP) Category 5/5e
cable, or better data grade cabling. While a
Category 3 or 4 cable may initially seem to
work, it will soon cause data loss.
Step 6: Supply power to the Fast Ethernet High Power
PoE Switch.
A. Connect one end of the power cable to the Switch.
B. Connect the power plug of the power cable to a
standard wall outlet.
When the Switch receives power, the Power LED should
remain solid Green.
Power Requirements DC 48V, 1.5A.
Power Consumption Max.62 watts / 211.5 BTU
Dimensions
(W x D x H) 90 x 80 x 21mm
Weight 172g
Power over Ethernet
PoE Standard
IEEE 802.3af Power over Ethernet
/ PSE
IEEE 802.3at Power over Ethernet
Plus / PSE
PoE Power Supply
Type Mid-Span
Power Pin Assignment 4/5(+), 7/8(-)
PoE Power Output
Per Port 48V DC, 375mA. Max.
15.4 watts (IEEE 802.3af)
Per Port 48V DC, 375mA. Max. 30
watts (IEEE 802.3at)
PoE Power Budget 60 watts
Number of 802.3af PD
Class 0, 1, 2, 3 can
be powered
4
Number of 802.3at PD
Class 1, 2, 3 can be
powered
4
7. Product Specications
Model
FSD-504HP
4-Port 10/100Mbps 802.3af / at
PoE + 1-Port 10/100Mbps Desktop
Switch
Hardware Specications
Network Connector 5-Port RJ-45 for 10/100Base-TX,
auto MDI / MDIX
PoE Inject Port 4-Port with 802.3af / at PoE
injector function (Port 2 to port 5)
LED Display
System: Power (Green)
Per PoE port: PoE (Orange, port
2 to port 5)
LNK/ACT (Green, port 1 to port 5)
Switch Architecture Store and Forward switch
architecture
MAC Address Table 1K MAC address table with Auto
learning function
Switch Fabric 1Gbps
Switch Throughput 0.74Mpps @64Bytes
Maximum Packet Size 1536Bytes
Flow Control
Back pressure for Half-Duplex.
IEEE 802.3x Pause Frame for Full-
Duplex
Number of 802.3at
PD Class 0, 4 can be
powered
2
Standard Conformance
EMI Safety FCC Class A, CE
Standard Compliance
IEEE 802.3
IEEE 802.3u
IEEE 802.3x
IEEE 802.3af
IEEE 802.3at
Ethernet
Fast Ethernet
Flow Control
Power over
Ethernet
High Power over
Ethernet
Environment
Operating
Environment 0 ~ 50 degrees C
Storage Environment -10 ~ 70 degrees C
Operating Humidity 5 ~ 95%, relative humidity, non-
condensing
Storage Humidity 5 ~ 95%, relative humidity, non-
condensing
8. Customer Support
Thank you for purchasing PLANET products. You can
browse our online FAQ resource on PLANET Website
rst to check if it could solve your issue. If you need
more support information, please contact PLANET switch
support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]w
Copyright © PLANET Technology Corp. 2013.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product: 4-Port 10/100Mbps 802.3af/at PoE + 1-Port 10/100Mbps Desktop Switch
*Model Number: FSD-504HP
* Produced by:
Manufacturer‘s Name : Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022 (2010 + AC:2011)
EN 61000-3-2 (2006 + A1:2009 + A2:2009)
EN 61000-3-3 (2008)
EN55024 (2010)
IEC 61000-4-2 (2008)
IEC 61000-4-3 (2010)
IEC 61000-4-4 (2012)
IEC 61000-4-5 (2005)
IEC 61000-4-6 (2008)
IEC 61000-4-8 (2009)
IEC 61000-4-11 (2004)
EN60950-1 (2006 + A11:2009 + A1:2010 +
A12:2011)
Responsible for marking this declaration if the:
Manufacturer Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name: Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Person responsible for making this declaration
Name, Surname Kent Kang
Position / Title : Product Manager
Taiwan 15th Nov., 2013
Place Date LegalSignature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:[phone] Fax:[phone]