Porsche USB-CDR30 User manual

Courtesy of:DiscountCarStereo.com
USB-CDR30
Quick
QuickQuick
Quick Start
StartStart
Start Install
InstallInstall
Installation
ationation
ation Guide for
Guide forGuide for
Guide for
Po
PoPo
Porsche CDR30
rsche CDR30rsche CDR30
rsche CDR30/31
/31/31
/31 R
RR
Radios
adiosadios
adios
Revised: January 10, 2018

Introduction:
Introduction:Introduction:
Introduction:
Portable audio products are everywhere, reflecting demand from
active people all over the world to ta e their music with them.
Porsche offers an optional 3.5mm jac for the CDR30
optional 3.5mm jac for the CDR30 optional 3.5mm jac for the CDR30
optional 3.5mm jac for the CDR30 and CDR31
and CDR31 and CDR31
and CDR31
Radio
Radio Radio
Radio which may be satisfactory to some, but those loo ing for a
better solution we offer the USB-CDR30.
..
. The USB-CDR30 replaces
the optional 3.5mm jac and allows the user to play and charge
play and chargeplay and charge
play and charge all
Apple lightning devices without sacrificing the loo and feel of the
dashboard components .
Installation:
Installation:Installation:
Installation:
Warning!
Warning!Warning!
Warning!
Although not critical, we recommend disconnecting the car
battery.
1. Remove CDR30/31 radio from dashboard to gain access to
the connectors. (Radio removal not covered in these
instructions)
2. With radio removed disconnect factory Quadloc plug
(harness) from Radio (See Fig. 1
Fig. 1Fig. 1
Fig. 1 )
Fig. 1
Fig. 1Fig. 1
Fig. 1
Factory Quadloc
3. To remove radio plug, push up on tab (indicated by blac
arrow in F
FF
Fi
ii
ig
gg
g.
..
. 2
22
2) and pull outwards on loc release
4. Connect plug on adapter harness to Radio (See To Radio in
in in
in
Fig. 3
Fig. 3Fig. 3
Fig. 3)
5. Disconnect the 12-pin green
greengreen
green and blue
blueblue
blue mini-Quadloc plugs
from factory plug (See Fig. 1
Fig. 1Fig. 1
Fig. 1)
Warning!
Warning!Warning!
Warning!
CDR30/31 Radios with factory AUX and Bluetooth will
have both a blue and green 12-pin mini-Quadloc (Green
reenreen
reen for AUX
and blue
blueblue
blue for Bluetooth). The AUX mini-Quadloc remains
disconnected and replaced with the blac
blacblac
blac 12-pin mini-Quadloc
from Adapter. (See Fig. 2
Fig. 2Fig. 2
Fig. 2)
6. Reconnect 12-pin blue
blueblue
blue mini-Quadloc plug (from step 5) to
plug on adapter harness (To Radio in Fig. 3
Fig. 3Fig. 3
Fig. 3)

Fig. 2
Fig. 2Fig. 2
Fig. 2
Quadloc Plug on Adapter harness
Green sub
Green subGreen sub
Green sub-
--
-plug remains disconnected
plug remains disconnectedplug remains disconnected
plug remains disconnected (See Fig. 2
Fig. 2Fig. 2
Fig. 2)
7. Connect factory plug (from step 2) to mating connector on
Adapter harness (To Car in Fig.
Fig.Fig.
Fig. 3
33
3)
Fig. 3
Fig. 3Fig. 3
Fig. 3
plug/connector on adapter harness
Ensure connections are snug
Ensure connections are snugEnsure connections are snug
Ensure connections are snug
Note to Vehicles with BOSE:
Note to Vehicles with BOSE: Note to Vehicles with BOSE:
Note to Vehicles with BOSE: You must transfer optical cable
You must transfer optical cable You must transfer optical cable
You must transfer optical cable
from factory
from factoryfrom factory
from factory plug to
plug to plug to
plug to plug
plug plug
plug supplied with adapte
supplied with adaptesupplied with adapte
supplied with adapter.
r.r.
r.
8. Decide where and how to mount USB terminal.
A. Flush mount requires drilling a ¾” hole in the dash
Flush mount requires drilling a ¾” hole in the dashFlush mount requires drilling a ¾” hole in the dash
Flush mount requires drilling a ¾” hole in the dash
B. USB mounting brac et
USB mounting brac et USB mounting brac et
USB mounting brac et without drilling
without drillingwithout drilling
without drilling (use this option
to mount the USB terminal wherever your installation
demands)
C. Un
UnUn
Un-
--
-mounted
mountedmounted
mounted (Free standing USB terminal)
A.
A.A.
A.Flush Mounting
Flush MountingFlush Mounting
Flush Mounting to
toto
to Dash
DashDash
Dash
1. Drill a ¾” hole in dash using a step drill bit or equivalent
(See Fig. 4
Fig. 4Fig. 4
Fig. 4)
Fig. 4
Fig. 4Fig. 4
Fig. 4
Step drill bit
2. Insert the male end of the 3ft USB extension cable (See Fig. 5
Fig. 5Fig. 5
Fig. 5)
through the ¾” hole in dash and mate with USB Female
terminal on adapter (See Fig. 6
Fig. 6Fig. 6
Fig. 6)

Fig. 5
Fig. 5Fig. 5
Fig. 5
USB extension cable
Fig. 6
Fig. 6Fig. 6
Fig. 6
USB Male (left) USB Female (Right)
3. Push USB head ( See Fig. 7
Fig. 7Fig. 7
Fig. 7) through hole until it snaps in
place and flush with mounting surface (See Fig. 8
Fig. 8Fig. 8
Fig. 8)
Fig. 7
Fig. 7Fig. 7
Fig. 7
Flat USB Terminal
Fig. 8
Fig. 8Fig. 8
Fig. 8
Flush mounted USB terminal
4. Tuc and secure extra wire from moving parts and test
operation (See Enabling the AUX
Enabling the AUXEnabling the AUX
Enabling the AUX section below)
B.
B.B.
B. Mounting Bracket
Mounting BracketMounting Bracket
Mounting Bracket without drilling
without drillingwithout drilling
without drilling
1. Locate a flat surface at location of choice within 7 ft. of radio
to mounting brac et to surface using adhesive/tape or screws.
(See Fig. 9
Fig. 9Fig. 9
Fig. 9)
Fig. 9
Fig. 9Fig. 9
Fig. 9
mounting brac et
2. Insert male end of 3ft USB extension cable through hole in
brac et (See Fig. 10
Fig. 10Fig. 10
Fig. 10) and mate with Female USB terminal

from Adapter (See Fig. 11
Fig. 11Fig. 11
Fig. 11)
Fig. 10
Fig. 10Fig. 10
Fig. 10
USB Male (left) USB Female (right)
Fig. 11
Fig. 11Fig. 11
Fig. 11
USB Male (left) USB Female (Right)
3. Push USB head through hole in mounting brac et until it
snaps in place and flush (See Fig 12
Fig 12Fig 12
Fig 12)
Fig. 12
Fig. 12Fig. 12
Fig. 12
4. Tuc and secure extra wire away from moving parts and test
operation ( See Enabling the AUX section
See Enabling the AUX sectionSee Enabling the AUX section
See Enabling the AUX section )
C.
C.C.
C. Un
UnUn
Un-
--
-Mounted (Free
Mounted (FreeMounted (Free
Mounted (Free Standing)
Standing)Standing)
Standing)
USB Terminal
USB TerminalUSB Terminal
USB Terminal
Simply route USB terminal (See Fig. 13
Fig. 13Fig. 13
Fig. 13) from behind the dash to
location of choice within 4 ft. of radio and connect your Apple
lightning cable.
Fig. 13
Fig. 13Fig. 13
Fig. 13
Free standing USB Terminal
Test Operation
Test OperationTest Operation
Test Operation
1. Connect Apple device to USB Terminal
2. Audio device will begin charging
3. On Radio, press CD/AUX
CD/AUXCD/AUX
CD/AUX button repeatedly until “AUX
AUX AUX
AUX
Mode
ModeMode
Mode” is enabled.
Note: To switch from CD to AUX press the “AUX” Soft ey.
4. Select a trac from devices music library and it will play on
the car spea ers.
Warning!
Warning!Warning!
Warning! Playlist and Trac selection is *NOT* possible from the
radio. You must use the iPod built-in controls to access music files.

5. Use the radio volume control to set playbac level
6. If successful operation is confirmed go ahead and reinstall
Radio
Alert!
Alert!Alert!
Alert! Apple authentic Lighting cable is required for proper
operation. Knoc –off Lightning cables will charge but may not
play music.
Compatibility
CompatibilityCompatibility
Compatibility
The USB-CDR30 wor s on the following Apple Lighting devices.
iPhone Models iPad Models iPod Models
iPhone X
iPhone 8
iPhone 8 Plus
iPhone 7
iPhone 7 Plus
iPhone 6s
iPhone 6s Plus
iPhone 6
iPhone 6 Plus
iPhone SE
iPhone 5s
iPhone 5c
iPhone 5
iPad Pro 10.5-inch
iPad Pro 12.9-inch (2G)
iPad Pro 12.9-inch (1G)
iPad Pro 9.7-inch
iPad
iPad mini 4
iPad mini 3
iPad mini 2
iPad mini
iPad Air 2
iPad Air
iPod touch 6G
iPod touch 5G
iPod nano 7G
Disclaimer
DisclaimerDisclaimer
Disclaimer
• This product has no affiliation with Porsche or Apple
• There are no warranties expressed or implied by purchase of this product
•Aux must be enabled, otherwise visit your Porsche dealer for assitance
• We’re not liable for misuse of this product.
•We recommend professional installation.
Call 804-717-5717 or email [e-mail]
© 1995-Jan-18 Discount Car Stereo, Inc. All rights reserved. Information in this document is
subject to change without notice. Other products and companies referred to herein are
trademar s or registered trademar s of their respective companies or mar holders.