Portech MV-370 User manual

MV-370
VoIP GSM Gateway
User Manual
PORTech Communications Inc

Content
1. INTRODUCTION.................................................................................................................1
2. FUNCTIONS......................................................................................................................... 1
3. THE CONTENTS IN PACKAGE.......................................................................................1
4. DIMENSION AND PANEL DESCRIPTION.................................................................... 2
5. ACCESSORY ATTACHMENT.......................................................................................... 3
6. SETTING AND MANAGING VIA WEB PAGE.............................................................. 4
7. SYSTEM INFORMATION................................................................................................. 5
. ROUTE.................................................................................................................................. 5
9. MOBILE ............................................................................................................................. 10
10. NETWORK....................................................................................................................... 17
11. SIP SETTING....................................................................................................................21
12. NAT TRANS .....................................................................................................................30
13.SYSTEM AUTH.................................................................................................................31
14.SAVE CHANGE................................................................................................................ 32
15.UPDATE............................................................................................................................. 33
16.REBOOT.............................................................................................................................35
17. SETTING AND CHECKING VIA IVR......................................................................... 36
1 .SPECIFICATION.............................................................................................................. 3
19. APPLICATIONS.............................................................................................................. 39
20. SIMPLE STEPS................................................................................................................ 40

21. APPENDIX: SETUP MV-370 WITH ASTERISK........................................................ 41
22.HOW TO SETUP ASTERISK TO RECEIVE CALLER ID FROM .......................... 47

1. Introduction
MV-370 series products provide you the best connect solution
for heterogeneous network （including ：WLAN 、GSM or
PSTN ）You may use a SIP-protocol VoIP phone or software to
connect to the MV-370, then reach this call to the mobile network,
and vice versa With multiple sets of MV-370, you may even build
an international call network
2. Functions
2 1 VoIP (SIP)-GSM conversion
2 2 VoIP (SIP)-CDMA conversion
2 3 Voice response for setting and status enquiring (Dial in GSM
numbers of MV-370 to get voice information or to operate )
2 4 50 sets of LAN->MOBILE routing, and 50 sets of MOBILE-
>LAN routing
2 5 Series connections to save bills
2 6 Standard SIP (RFC2543, RFC3261) protocol to communicate
with other gateways or PC
2 7 settings and managing via web page
3. The contents in package
3 1 MV-370 main body
3 2 AC-DC Adaptor (110V AC – 12V DC or 220V AC – 12V DC)
-1-

3 3 Network cable
3 4 Antenna
3 5 User’s Manual
When you receive MV-370 package and find it is damaged or
incorrect, please contact your vendor
4. Dimension and Panel description
-2-
(3.1) (3.2)
(3.4)
(3.3)
14.5cm
3.9cm

4 1 Antenna：Antenna connector
4 2 DC 12V：Power socket
4 3 LAN: Standard RJ-45 socket, connecting to Hub circuit
4 4 PWR: Power indicator light, red light Light is on when
system’s power supply is normal
4 5 MOBILE: GSM indicator light, green light Light flashes when
GSM status is normal; light turns on constantly when GSM is
called
4 6 LAN: LAN indicator light, green light Light flashes when Lan
is called; light turns off when GSM answered
4 7 LINK: Link indicator light, green light Light is on when
network is connected correctly
5. Accessory attachment
5 1 Connect the network cable both to your Hub and to LAN
socket of MV-370
5 2 Connect the antenna and place it in a good receiving location
(not too close to the device)
5 3 Insert a SIM card into back of MV-370
5 4 Plug the adapter in DC 12V socket and PWR socket The
PWR light should turn red at the moment
5.5 lick reset button 3 sec. MV-370 will restore default IP.
Other setting as usual.
-3-
(4.1) (4.2) (4.3) (4.4) (4.6)
(4.5) (4.7)
17cm

6. Setting and managing via web page
The default IP address of MV-370 is http://192 168 0 100 Before
accessing the web page, please confirm this address is available
in your network
Enter the default username and password to login
Default username: voip
Default password: 1234
-4-

7. System Information.
7 1 After login, you could see the system information such as: model
name, firmware version, codec version name, etc in this page
7 2 You could also see the setting table in the left side Please click on
the option you would like to set The setting methods are indicated
as the following chapters, please input the value or select the item
according to your situation
Note:
Please remember to save change whenever you submit any setting Click “Save
Change” then “Save” button, the system will restart and make the changed
function/setting operative
8. Route
8 1 Route/ Mobile to LAN Settings
-5-

In this page: Mobile To Lan Table, you could set the routing rules to
transfer the calls incoming from MOBILE to LAN Maximum 50 sets
When the GSM number of the MV-370 is called, this device transfers
the call to URL according to the caller ID of the incoming call
8 1 1 CID: caller ID, the numbers of incoming call
You could set the CID as the following formats:
(1) The complete number, e g 0911111111
(2) The prefix part plus *, e g 0911* This format means any number
starting with 0911 will be accepted to transfer
(3) *, this means any incoming call is accepted to transfer
(4) N, this means the incoming call without showing its CID is
accepted to transfer
Please note the priority of the routing rules; the CID with more digits
-6-

gets the priority
8 1 2 URL：The IP address of destination
You could set the URL as the following formats:
(1) The complete IP address, e g 192 168 0 101
(2) The proxy extension numbers
(3) The phone numbers
Note: If the device has registered at proxy server/Asterisk,
you can enter any destination phone number. Also note
that in the proxy server/Asterisk, you need to set the
route of destination phone number.
(4) Leave it blank or ‘N’, this mean to refuse to transfer
(5) *, this means to transfer via 2-stage-dialing The call will be
answered with a prompt dial tone for the caller to press the IP
address, proxy extension, or any phone number as destination
The caller press the IP address on the phone keys:
192*168*0*101# as 192 168 0 101
8 1 3 Example of Mobile to Lan setting:
(1) Mobile to Lan: 0932*, 0911123456
When the GSM numbers of the device is called, if the caller’s
prefix numbers are 0932, MV-370 transfers the call to
0911123456, then 0911123456 rings (while available)
Precondition:
a MV-370 has registered at proxy server/Asterisk
b The proxy server/Asterisk has the route of “09”
(2) Mobile to Lan: *, *
Any incoming call gets a prompt dial tone; so the caller can enter
any IP address, sip extension, or phone number
Precondition:
a SIP extension or phone number needs to register at SIP Proxy
Server or Asterisk
-7-

b Phone number, SIP Proxy Server or Asterisk needs to set the
route of destination phone number
8 2 Route/ Mobile to LAN Speed Dial Settings
When you set both Mobile to LAN Speed Dial Settings and Mobile
to LAN settings at the same time, Mobile to LAN Speed Dial
Settings gets higher priority Mobile to Lan setting will be not
available
The call is answered with a prompt dial tone for the caller to press the
“Num”, and then the device connects the “URL” as destination
Example: after you call the GSM number of the device and hear a dial
tone, you press 0, then the lan phone of IP address:
192 168 0 107 rings
-8-

8 3 Route/ LAN to Mobile Settings
In this page: Lan To Mobile table, you could set the routing rules to
transfer the calls incoming from Lan to Mobile Maximum 50 sets
When the Lan of the MV-370 is called, this device transfers the call to
Call Num according to the URL of the incoming call
8 3 1 URL: The IP address or proxy extension numbers of the incoming
call
You could set the URL as the following formats:
(1) The complete IP address, e g 192 168 0 101
(2) The proxy extension numbers, e g 103
(3) Part of an IP address plus *, e g 192 168 0 * This means the IP
address starting with 192 168 0 would be accepted to transfer,
(4) Part of the proxy extension numbers plus, e g 10* This means
the extension numbers starting with 10 would be accepted to transfer
8 3 2 Call Num: the phone numbers of destination
You could set the Call Num as the following formats:
(1) The complete number, e g 0911111111
-9-

(2) *, this means to transfer via 2-stage-dialing The call will be
answered with a prompt dial tone for the caller to press the destination
phone numbers, e g 0911111111
(3) #, this allow the caller with lan phone dial directly the destination
numbers
Precondition:
(1) MV-370 and incoming lan Phone are both registered at
proxy server or Asterisk
(2) Proxy server/asterisk has set the routing rules to assign
specific prefix of numbers to be transferred from MV-370
(3) Lan to Mobile routing sets: *, #
Usage: You could dial on your lan phone call any destination
number with prefix of “09” When your lan phone and MV-
370 had registered and “09” prefix is setted the routing
rules at proxy server or Asterisk
(4) #['d'n]['a'ppp], this means to do the above routing, and to modify
the numbers
Note: 'd'n means to delete the number of prefix,
'a'ppp means to add 'ppp' prefix
E g #d2a09 means to call the registered numbers via one-stage-
dialing The numbers are modified to: delete 2 digits of prefix of
the original numbers, then add 09 to be new prefix of the
destination numbers
9. Mobile
9 1 Mobile/ Mobile Status
In this page: Mobile Status, you could get the information of your GSM
network and the latest operation
-10-

(1)Network Registration：The telecom carrier which the SIM card been
registered
(2)SIM Card ID：SIM card ID
(3)Signal Quality：Signal quality
(4)GSM S/N : IMEI Number
(5)Incoming IP：The IP address of the last incoming call from LAN
(6)Incoming IP Name: proxy server name
(7)Outgoing IP：The IP address of the last outgoing call to LAN
(8)Incoming Mob：The caller ID of the last incoming call from MOBILE
(9)Outgoing Mob ：The called number of the last outgoing call to
MOBILE
-11-

9 2 Mobile/ Mobile Setting
In this page: Mobile setting, you could adjust the parameter and click
on the option to fit your need You could leave those default value
before you had tried the complete operation of this device.
(3)LAN Dialtone Gain: DTMF Reciver is not good,you can adjust gain
down
(4) ON/Off: If you use this channel,please click on Otherwise,please
click off
-12-
(1) (2)
(3)
(5) (6)
(7)
(8)
(9)
(10)
(11)
(4)
GSMVoIP Codec
LAN (6)Rx
(5) x
D MF
(12)

(5)CODEC Tx Gain: as above
(6)CODEC Rx Gain: as above
(7) SIP From: Caller ID transfer
Tel/User(Standard): If you need to register to Asterisk and proxy
server,please choose this option And how to transfer the caller
ID to LAN,please refer 22 How to setup Asterisk to receive
Caller ID from MV-370 (page 43)
MV-370-2 will send the message as follows in the Packet
From: " caller number " <sip:[email protected]>;tag=51088abb
Tel/Tel :
MV-370 will send the message as follows in the Packet
From: "caller number" <sip: caller number @192.168.0.228>;tag=6ac93f7c
※Please note:If you choose this option,please don’t register to
Asterisk and proxy server Please only fill proxy server ip and
choose Active: on (else field empty) in sip setting/service
demain
User/Tel
MV-370 will send the message as follows in the Packet
From: " Username " <sip: caller number @192.168.0.228>;tag=7f130947
※If you choose this option,please don’t register to Asterisk and
proxy server Please only fill proxy server ip,Username and
choose Active: on (else field empty) in sip setting/service
demain
(8)Presentation CLIR : If you need to block the Caller Id for call
termination,please choose Suppression
(9)Mobile PIN Code:If you need to unlock pin code via MV-370,you can
click “On” and enter pin code
(10)LAN Answer Mode:
Answered : when mobile answer,then connect the call
Alerted : when the mobile is ringing back tone,then connect the call
Income : when lan dial out,then connect soon
(11)Band Type:When you buy Quad band,you need to choose your
GSM frequency
-13-

(12)Answer Delay: Delay for incoming call when the ring
9.3 Mobile / Forward Setting :
When the first route are busying, SIP can transfer phone call to
another free route When the device are busying, the phone call
can be transfer to another device (external equipments)
* "Forward Enable" is not motivate on Defualt value
So please, mark "Forward Enable" this blank to motivate this
function
Take SJ Phone for example: Profiles -> Edit -> Advanced -> Accept
redirection replies (Turn on the "Forward Enable", therefore the SJ
Phone can designate a port which are free to use )
-14-

Name URL:Port
Fwd to Mobile1:
Fwd to Mobile2:
Fwd to External:
The Explanation of Picture:
Fwd to Mobile1:192 168 0 100 : 5060, it means when 5062 Port are
busying, SJ Phone can transfer the call to 5060 Port
(192 168 0 100)
Fwd to Mobile2:192 168 0 100 : 5062, it means when 5060 Port are
busying, SJ Phone can transfer the call to 5062 Port
(192 168 0 100)
If both 5060 port and 5062 port are busying at same time, you can
set up "Fwd to External", then you can transfer the phone call to
-15-

another designate device
9.4 Mobile / SMS Agent :
(1) Rx List: Read received SMS
(2) Dest Num: the Receiver’s phone number
(3) Message: Please fill the message that want to send to receiver
When you click Rx List, you can view all received SMS as follows
-16-
Read received SMS