PotteryBarn LOGAN HUTCH WITH SHELVES 24 inch User manual


Date:3‐Apr‐15www.potterybarn.com  Page1of6
Rev:  










LOGAN BASE WITH DRAWERS 24”





Date:3‐Apr‐15www.potterybarn.com  Page2of6
Rev:  
Important Safety Instructions:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is strongly recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free work surface, as
this will avoid damaging parts during assembly. The shipping box provides an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage hardware and split
wood.
This unit can be assembled with other Logan components to setup as the Media Suite or Office Suite.
Parts Included:
(1) Base with drawers 24”
Hardware Included:

(a)
Connecting Screw
M4 x 25mm
2x
(b)
Sleeve



M4 x 19mm
2x
(c)
Drill Bit
diam 5mm
1x
(d)
Allen key
4mm thick
1x
Anti-Tip Kit
Tools Required (not included):
Phillips head screwdrivers
Drill


Date:3‐Apr‐15www.potterybarn.com  Page3of6
Rev:  
Assembly Instruction Steps:
1. Using caution remove all components from their boxes making sure to set aside all hardware and parts.
2. To connect base with the TV Stand, Desk, Corner Cabinet/TV Stand or a separate base:
Set the base on the side of these units. Pull out the top two drawers and set them aside. Using the pilot holes as
a guide, bore holes on the side panels using a drill with the 5mm drill bit (c).
NOTE: The pilot holes on side panel to be drilled through are countersink holes. Do not drill the shelf pin holes.
Only bore holes if this base is to be connected with other pieces in the Logan Collection.

3. Adjusting the levelers:
Due to an uneven floor, the furniture may not sit level due causing it to wobble. If the furniture wobbles, determine
which corner does not touch the ground correctly. With two people follow these steps:
1) Pull out the bottom drawer and adjust the levelers using theAllen key (d) on the interior holes of the bases
until adequate contact will be made with the floor. Gently set down the piece and check stability and door
alignment.
2) Repeat steps until furniture sits firmly and the holes on pieces to be connected are properly aligned.
Shelf pin hole.
NOTE: Pilot hole is
countersink hole.


Date:3‐Apr‐15www.potterybarn.com  Page4of6
Rev:  
4. Align the bored holes on the side panel of the base with the bored holes on the Logan TV Stand, Desk, Corner
Cabinet/ TV Stand, or a separate base. Insert the sleeve (b) into the hole and secure with the connecting screw
(a) on the other end by tightening and threading the sleeve using Phillips head screwdrivers. Repeat with the
other sleeve and screw.
5. To connect bas with a 24” hutch: Carefully set a 24” hutch on top of this base.Align the holes under the hutch
with the pre-drilled holes on the top of the base, secure using the connecting screws and sleeves enclosed in
the hardware packet of hutch. Tighten with the Phillips head screwdriver (see separate hutch instructions for
more detailed steps).
Side
panels


Date:3‐Apr‐15www.potterybarn.com  Page5of6
Rev:  
6. Re-install the two drawers back into the cabinet.
7. Once the assembled unit is moved into its final location, install included anti-tip kit.
8. If the furniture still wobbles, pull out the bottom drawer and adjust the levelers through the holes at the four
corners with the Allen key 4mm (d).
9. Assembly is complete.
NOTE: USE THE ANTI-TIP KIT PROVIDED TO SAFELY SECURE YOUR PRODUCT(S). FOLLOW THE
INSTRUCTIONS PROVIDED TO PREVENT SERIOUS INJURY FROM TIPPING FURNITURE.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
Thankyouforyourpurchase
Stores|catalog
12
345