Powerfix Profi PTSI 9 A1 User manual

IAN 78445
INFRARED TEMPERATURE PROBE PTSI 9 A1
INFRARED TEMPERATURE
PROBE
Operating instructions
INFRARØD-TERMOMETER
Betjeningsvejledning
INFRARÖD TERMOMETER
Bruksanvisning
INFRAPUNALÄMPÖMITTARI
Käyttöohje
INFRAROT-TEMPERATUR-
MESSGERÄT
Bedienungsanleitung
3

GB/IE Operating instructions Page 1
FI Käyttöohje Sivu 17
SE Bruksanvisning Sidan 33
DK Betjeningsvejledning Side 49
DE/AT / CH Bedienungsanleitung Seite 65
Before reading, unfold the page containing the illustrations and familiarise your-
self with all functions of the device.
Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin
toimintoihin.
Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör
dig bekant med
apparatens/maskinens funktioner.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets
funktioner.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie
sich anschließend mit allen Funktionen des Gerätes vertraut.

1
PTSI 9 A1
GB
IE
Index
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Limited liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warnings used. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Interaction with batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Basic Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Initial use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Items supplied and transport inspection. . . . . . . . . . . . . . . . . . . . . . 6
Disposal of the packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Inserting / Replacing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating components. . . . . . . . . . . . . . . . . . . . . . . . . . 8
Handling and operation. . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Switching the appliance on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Selection of the Temperature Unit . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Measuring the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Indicating a temperature deviation . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting reference values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Selection of the size of difference . . . . . . . . . . . . . . . . . . . . . . . . . 10
Scanning a temperature deviation. . . . . . . . . . . . . . . . . . . . . . . . . 11
Example of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Battery indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Malfunction causes and remedies . . . . . . . . . . . . . . . . . . . . . . . . . 12
Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disposal of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disposing of the batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Information regarding the EG Declaration of Conformity . . . . . . . 15
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
IB_78445_PTSI9A1_LB3.indb 1IB_78445_PTSI9A1_LB3.indb 1 25.10.12 15:3225.10.12 15:32

2PTSI 9 A1
GB
IE
Introduction
Congratulations on the purchase of your new appliance!
You have clearly decided in favour of a quality product. This ope-
rating manual is a component of this product. It contains important
information in regard to safety, use and disposal. Before using
the product, familiarise yourself with all of these operating and
safety instructions. Use the product only as described and only
for the specified areas of application. Retain these instructions
for future reference. In addition, pass these documents on, together
with the product, to any future owner.
Copyright
This documentation is copyright protected.
Any copying or reproduction, including as extracts, as well as
the reproduction of images, also in an altered state, is only
permitted with the written authorisation of the manufacturer.
Limited liability
All technical information, data and instructions for connection and
operation contained in these operating instructions correspond
to the latest available at the time of printing and, to the best of
our knowledge, take into account our previous experience and
know-how. No claims can be derived from the details, illustrations
and descriptions in these operating instructions. The manufacturer
assumes no responsibility for damage caused by failure to comply
with these operating instructions, improper use, incompetent repairs,
making unauthorised modifications or for using unauthorised
replacement parts.
Intended use
This infrared temperature probe is used for the contact-less
measurement of surface temperatures in the range of -40°C to
+220°C (-40°F–428°F) and comparison of the measured
temperatures with a previously acquired reference value.
IB_78445_PTSI9A1_LB3.indb 2IB_78445_PTSI9A1_LB3.indb 2 25.10.12 15:3225.10.12 15:32

3
PTSI 9 A1
GB
IE
The measurement is possible in either °C or °F. The measure-
ment is made by means of infrared technology. Thereby, the
surfaces of objects can be continuously measured and the tem-
perature variations are displayed optically, acoustically and in
colour. The integrated laser-beam pointer may only be used for
locating the measurement point within the scope of temperature
measurement. The appliance is intended exclusively for domestic
use. Do not use the appliance for commercial or industrial appli-
cations. Use the appliance only in a dry environment or indoors.
This appliance is not intended for any other use or for uses beyond
those detailed. Claims of any kind for damage resulting from
unintended use will not be accepted. The operator alone bears
the liability.
Warnings used
In these extant operating instructions the following warning
notices are used:
DANGER
A warning at this risk level indicates a threaten-
ingly dangerous situation.
In the event that the dangerous situation is not avoided it
could lead to death or serious physical injury.
► Comply with the directives in this warning to avoid the risks
of death or serious physical injury.
WARNING
A warning at this risk level indicates a potentially
dangerous situation.
If the dangerous situation is not avoided it could lead to
personal injuries.
► Comply with the directives in this warning to avoid personal
injuries.
IB_78445_PTSI9A1_LB3.indb 3IB_78445_PTSI9A1_LB3.indb 3 25.10.12 15:3225.10.12 15:32

4PTSI 9 A1
GB
IE
IMPORTANT
A warning at this risk level indicates potential
property damage.
If the situation is not avoided it could lead to property damage.
► Comply with the directives in this warning to avoid property
damage.
NOTICE
► A notice indicates additional information that may assist
you in the handling of the appliance.
Safety
In this section you will receive important safety information re-
garding the handling of the appliance. This appliance complies
with the statutory safety regulations. Incorrect usage can lead to
injuries and property damage.
WARNING
This appliance contains a Class 2 laser.
NEVER direct the laser beam at people or animals.
NEVER look directly into the laser. The laser can cause
serious eye damage.
► Do NOT direct the laser beam at strongly reflective
materials. Reflected laser beams are also dangerous.
► All adjustments intended to increase the laser power
are forbidden. There is also a risk of personal injury!
► No liability will be accepted for damage resulting
from manipulation of the laser equipment or from non-
compliance with this safety information.
IB_78445_PTSI9A1_LB3.indb 4IB_78445_PTSI9A1_LB3.indb 4 25.10.12 15:3225.10.12 15:32

5
PTSI 9 A1
GB
IE
DANGER
► Do not use the appliance at locations with a risk of fire
or explosion, e.g. close to flammable fluids or gases.
Interaction with batteries
WARNING
Risks from improper use!
The risk of explosions and leakages exists!
For the safe handling of batteries, comply with the following
safety instructions:
► Do not throw batteries into a fire.
► Never short-circuit batteries.
► Do not attempt to recharge batteries.
► Regularly check the condition of the batteries. Leaking bat-
tery acid can cause permanent damage to the appliance.
Special caution should prevail when handling damaged
or leaking batteries. There is also a risk of personal injury!
Wear protective gloves.
► Store batteries in a place inaccessible to children. If a bat-
tery is swallowed, seek medical attention IMMEDIATELY.
► If you do not intend to use the appliance for an extended
period, remove the batteries.
Basic Safety Instructions
For safe handling of the appliance comply with the following
safety instructions:
■ Before use check the appliance for visible external damage.
Do not take into operation an appliance that is damaged or
has been dropped.
■ Do not make any changes or modifications to the appliance
yourself.
IB_78445_PTSI9A1_LB3.indb 5IB_78445_PTSI9A1_LB3.indb 5 25.10.12 15:3225.10.12 15:32

6PTSI 9 A1
GB
IE
■ This appliance is not intended for use by individuals (including
children) with restricted physical, physiological or intellectual
abilities or deficiencies in experience and/or knowledge
unless they are supervised by a person responsible for their
safety or receive from this person instruction in how the appli-
ance is to be used.
■ Children should be supervised to ensure that they do not
play with the appliance.
■ Protect the appliance against moisture and the penetration
of liquids.
■ Do not operate the appliance in the vicinity of open flames
(e.g. candles).
■ Avoid direct sunlight.
Initial use
DANGER
Damage to property and injuries to people may
occur when taking the appliance into use!
► Packaging material should not be used as a play thing.
There is a risk of suffocation!
Items supplied and transport inspection
The appliance is delivered with the following components as
standard:
▯ Infrared Temperature Probe
▯ 9 V Block battery
▯ This operating manual
IB_78445_PTSI9A1_LB3.indb 6IB_78445_PTSI9A1_LB3.indb 6 25.10.12 15:3225.10.12 15:32

7
PTSI 9 A1
GB
IE
NOTICE
► Check the contents to ensure everything is available and
for signs of visible damage.
► If the items supplied are incomplete, or damaged due to
defective packaging or transportation, contact the Service
Hotline (see section Service).
Disposal of the packaging
The packaging protects the appliance against transport damage.
The packaging materials are selected from the point of view of
their environmental friendliness and disposal technology and
are therefore recyclable.
The recirculation of packaging into the material circuit saves
on raw material and reduces the amount of waste generated.
Dispose of packaging material that is no longer needed as per
the regionally established regulations.
Inserting/Replacing the battery
The appliance needs a 9 V battery to operate.
♦ Open the battery compartment on the underside of the
handle.
♦ Insert the battery, complying with the specified polarities
given on the battery compartment cover, into the battery
compartment .
♦ Close the battery compartment cover. The battery compartment
lid must audibly engage.
IB_78445_PTSI9A1_LB3.indb 7IB_78445_PTSI9A1_LB3.indb 7 25.10.12 15:3225.10.12 15:32

8PTSI 9 A1
GB
IE
Operating components
Laser-beam exit opening
Infrared sensor
Display
Button
Button °C/°F/SET
Button
Battery compartment
Measuring button
Handling and operation
In this chapter you will receive important information for the
handling and operation of the appliance.
Preparing the appliance
The appliance is ready for use after inserting the battery.
Grasp the handle of the appliance so that the index finger can
operate the measuring button and the thumb can operate
the buttons - . The appliance is suitable for left and right
handers.
Switching the appliance on/off
♦ Press the measuring button to switch the appliance on.
The display lights up and a brief signal tone is heard.
♦ Press and hold the button ° C /° F/SET for approx. 3 seconds
to switch the appliance off. Two brief signal tones will be heard.
♦ If the appliance is not currently in use, the back light of the
display switches off after approx. 15 seconds. After ap-
prox. 60 seconds the appliance switches off automatically,
two short signal tones notify this.
IB_78445_PTSI9A1_LB3.indb 8IB_78445_PTSI9A1_LB3.indb 8 25.10.12 15:3225.10.12 15:32

9
PTSI 9 A1
GB
IE
Selection of the Temperature Unit
After switching on, the default temperature unit is shown as
degrees Celsius (°C).
♦ Briefly press the button °C/°F/SET to switch to the unit
of degrees Fahrenheit (°F).
♦ Briefly press the button °C/°F/SET again to switch back
to the unit of degrees Celsius (°C).
Measuring the temperature
♦ Press the measuring button and point the laser dot on the
spot to be measured.
Whilst the measuring button is pressed, the temperature is
measured and in the display “SCAN” is shown.
After releasing the measuring button the last measured
temperature is indicated on the display and the laser dot is
switched off.
To obtain the most accurate measurement, please note the
following:
■ The determined temperature is the average temperature of the
measured area. These increases in the ratio of 8:1, the further
away the appliance is from the object being measured.
D = Distance, S = Surface
■ The target object must be greater than the measuring surface
of the appliance. The smaller the target object is, the less the
distance between appliance and target object must be.
■ Select the smallest possible distance to the surface being
measured.
IB_78445_PTSI9A1_LB3.indb 9IB_78445_PTSI9A1_LB3.indb 9 25.10.12 15:3225.10.12 15:32

10 PTSI 9 A1
GB
IE
■ Aim the appliance as perpendicularly as possible to the
surface being measured.
■ Do not measure in dusty, smoky or steamy atmospheres.
Do not measure through transparent materials, such as glass
or plastics.
■ In the event of extreme temperature fluctuations allow the
appliance to adjust to the ambient climatic conditions for
about 30 minutes before measuring.
Indicating a temperature deviation
A temperature deviation is the difference between a predetermined
reference value and a measured temperature. The deviations are
shown as figures and by using coloured indicator on the display.
In addition, they will also be pointed out by an acoustic signal.
Setting reference values
♦ Press the measuring button and point the laser dot on
the spot to be referenced. The temperature is shown in the
display .
♦ Now press, while holding the measuring button , the
button °C/°F/SET to accept the temperature value as a
reference value. The reference temperature is shown in the
display next to the indicator REF.
Selection of the size of difference
On the appliance you can now set at which temperature dif-
ference (ΔT) the colour display and the acoustic signal should
respond.
♦ Press, while the reference value is being shown in the dis-
play , the button or the button to set the
desired temperature difference (ΔT).
OFF 0.5°C
1°F
3°C
5°F
5.5°C
10°F
Lower temperature threshold = Reference temperature – ΔT
Upper temperature threshold = Reference temperature + ΔT
IB_78445_PTSI9A1_LB3.indb 10IB_78445_PTSI9A1_LB3.indb 10 25.10.12 15:3325.10.12 15:33

11
PTSI 9 A1
GB
IE
Scanning a temperature deviation
♦ Press the measuring button and point the laser dot on the
spot to be measured. The temperature is shown in the display .
♦ While scanning, hold the measuring button down and
move the laser dot slowly and continuously over the surface
to be measured. The temperature deviations between the
reference and measurement values are presented as follows:
Colour
display Signal tone Result
Red fast Upper temperature
threshold exceeded
Green not available Within the temperature
threshold
Blue slow Lower temperature
threshold not reached
Example of application
For example, to check the penetration of cold air into an interior
through a window, first scan the temperature around the frame
immediately adjacent to the closed window. Select the warmest
part of the frame as a reference temperature and then, for
example, a temperature difference of 3°C/5°F.
Now scan again, evenly, all around the frame directly next to the
window. A possible ingress of cold air of more than 3°K difference
is indicated by the blue colour display and by a slow signal tone
sequence.
Battery indicator
A battery icon appears in the display when the battery
voltage is too low.
♦ Insert a new battery as described in the section “Inserting/
Replacing the battery”.
IB_78445_PTSI9A1_LB3.indb 11IB_78445_PTSI9A1_LB3.indb 11 25.10.12 15:3325.10.12 15:33

12 PTSI 9 A1
GB
IE
NOTICE
► With a low battery the accuracy of the temperature
display is limited.
Troubleshooting
In this section you will receive important information for the
localisation and remedying of malfunctions.
Malfunction causes and remedies
The following table will help with localising and remedying
minor malfunctions:
Defect Possible cause Solution
The display
is blank.
The battery is in-
correctly inserted.
Insert the battery as
per the markings on
the battery cover.
The battery is
discharged. Insert a new battery.
In the
display
appears the
Indicator „ErOL“.
The measured tempera-
ture is too low.
Repeat the measure-
ment at a different
location.
In the
display
appears
the Indicator
„ErOH“.
The measured tempera-
ture is too high
Repeat the measure-
ment at a different
location.
NOTICE
► If you cannot resolve the problem with the above steps,
please contact Customer Support (see section Service).
IB_78445_PTSI9A1_LB3.indb 12IB_78445_PTSI9A1_LB3.indb 12 25.10.12 15:3325.10.12 15:33

13
PTSI 9 A1
GB
IE
Cleaning
IMPORTANT
Damage to the appliance
► When you are cleaning the appliance ensure that no
moisture gets inside it, so as to avoid irreparable damage.
► Do not use chemical or abrasive cleaning materials. They
could damage the housing.
♦ Clean the appliance with a soft dry cloth.
♦ Clean the laser exit opening and the infrared sensor with a
gentle flow of air. For heavier soiling, remove it with a slightly
damp cotton swab. Do not exert any excessive pressure!
Storage
If you do not intend to use the appliance for an extended period,
remove the battery and store it in a clean, dry place away from
direct sunlight.
Disposal
Disposal of the appliance
Do not dispose of the appliance in your normal do-
mestic waste. This product is subject to the provisions
of the European Directive 2002/96/EC-WEEE (Waste
Electrical and Electronic Equipment).
Dispose of the appliance through an approved disposal centre
or at your community waste facility.
Pay heed to the currently applicable regulations. In case of doubt,
please contact your waste disposal centre.
IB_78445_PTSI9A1_LB3.indb 13IB_78445_PTSI9A1_LB3.indb 13 25.10.12 15:3325.10.12 15:33

14 PTSI 9 A1
GB
IE
Disposing of the batteries
Batteries may not be disposed of with household waste. All con-
sumers are statutorily obliged to dispose of batteries at a collection
site in their community/city district or at a retail store. This obliga-
tion is intended to ensure that batteries are disposed of in an
environmentally safe manner. Only hand in batteries that are
fully discharged.
Appendix
Technical data
Power supply 1 x 9 V Block battery
(6F22/6LR61)
Temperature measurement range -40°C up to +220°C
Measurement accuracy for T > 0°C ± 2°C repectively ± 2%
of measured value
Measurement accuracy for T < 0°C ± 3°C repectively ± 3%
of measured value
Laser class 2
Wave length (λ) 650nm
Output power (Pmax) < 1mW
Operating temperature 0°C up to 40°C
Air humidity
(no condensation) ≤ 75%
Dimensions : approx.
18 x 12 x 4.2 cm
Weight without battery approx. 167 g
IB_78445_PTSI9A1_LB3.indb 14IB_78445_PTSI9A1_LB3.indb 14 25.10.12 15:3325.10.12 15:33

15
PTSI 9 A1
GB
IE
Information regarding
the EG Declaration of Conformity
With regard to conformity with essential require-
ments and other relevant provisions, this device
complies with the guidelines of EN 61326-1,
EN 61326-2-2, EN 61010-1 as well as
EN 60825-1.
The complete original Declaration of Conformity
can be obtained from the importer.
Service
Service Great Britain
Tel.: [phone] (£ 0.10/Min.)
E-Mail: [email protected]
IAN 78445
Service Ireland
Tel.: [phone]
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak))
E-Mail: [email protected]
IAN 78445
Importer
KOMPERNASS GMBH
BURGSTRASSE 21
44867 BOCHUM, GERMANY
www.kompernass.com
IB_78445_PTSI9A1_LB3.indb 15IB_78445_PTSI9A1_LB3.indb 15 25.10.12 15:3325.10.12 15:33

16 PTSI 9 A1
IB_78445_PTSI9A1_LB3.indb 16IB_78445_PTSI9A1_LB3.indb 16 25.10.12 15:3325.10.12 15:33

17
PTSI 9 A1
FI
Sisällysluettelo
Johdanto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Tekijänoikeudet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Vastuurajoitus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Määräystenmukainen käyttö . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Käytetyt varoitukset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Turvallisuus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Paristojen käsittely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tärkeitä turvallisuusohjeita. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Käyttöönotto. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Toimitussisältö ja laitteen kuljetuksen jälkeinen tarkistaminen. . . . .22
Pakkauksen hävittäminen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Paristojen asentaminen/vaihtaminen . . . . . . . . . . . . . . . . . . . . . . 23
Käyttöelementit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Käyttö . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Laitteen käytön valmistelut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Laitteen kytkeminen päälle/pois päältä . . . . . . . . . . . . . . . . . . . . 24
Lämpötilayksikön valitseminen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lämpötilan mittaaminen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Lämpötilaerojen näyttö . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Viitearvon asettaminen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Lämpötilaeron suuruuden määrittäminen. . . . . . . . . . . . . . . . . . . . 26
Lämpötilaeron skannaaminen . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Käyttöesimerkki . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Pariston kapasiteetti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Vian määritys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Vikojen syyt ja korjaaminen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Puhdistaminen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Varastointi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Hävittäminen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Laitteen hävittäminen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Paristojen hävittäminen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Liite. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Tekniset tiedot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
EY-vaatimustenmukaisuusvakuutusta koskevia huomautuksia. . . . . 31
Huolto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Maahantuoja. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
IB_78445_PTSI9A1_LB3.indb 17IB_78445_PTSI9A1_LB3.indb 17 25.10.12 15:3325.10.12 15:33