Premier designs Wind Garden Sopwith Camel Airplane Spinner User manual

WindGarden
by premier designs
Sopwith Camel Airplane Spinner
assembly
instructions
Plane Fuselage x 1
Wing x 3 Landing Gear Struts x 2
Spinner Propeller x 1
Landing Gear Wheel Axle x 1
Stabilizer Cross Strut x 1
Ground Stake x 1
Support Pole x 1
A
“T” Fitting
Thumb
Screw
Vertical Support Rod
Diagonal
Plastic Fittings
B
Bottom View
Aluminum
Ferrule
Internal Wing
Strut
Internal Wing
Strut
Left Wing Right Wing
Velcro Tab
Velcro Tab
Main
Fuselage
Hub
Step 1
Slide the top wing’s“T”Fitting Thumb Screw onto the Internal
Vertical Support Rod. Be sure to tighten the top wing’s“T” Fitting
Thumb Screw to secure the wing to the fuselage. Make sure the
wing is fully seated on the Vertical Support Rod. (diagram A)
Step 2
Insert the Aluminum Ferrule attatched to the Internal Wing Strut
of the Right Wing through the square opening of the Main
Fuselage Hub. Then insert the Left Wing’s Internal Wing Strut into
the Aluminum Ferrule, which is inside the channel of the Main
Fuselage Hub. (diagram B )
Step 3
Secure the wings to the fuselage with the Velcro tabs on both the
top and bottom of the Left and Right Wings. (diagram C)
Main Fuselage
Hub
Fuselage
Velcro Tab
Velcro Tab
Left Wing Right Wing
C
Bottom View

G
Step 4
Insert both Landing Gear Struts through the Landing Gear Holes into the Landing Gear Sleeves, located at the front of the plane. These struts should cross each other and
form an“X”. Then insert the Landing Gear Struts into the two black Diagonal Plastic Fittings on either side of the top wing. Then insert the Landing Gear Wheel Axle into the
two black fittings located between the two landing gear pockets. Then secure all black,Wing Supports to the Velcro Wing Tabs located underneath the top wing. (diagram D)
Step 3
Insert the Stabilizer Strut into the Stabilizer Sleeves located underneath the
stabilizer. Guide the Stabilizer Strut through the Fuselage Stabilizer Hole and to the
other side. Then slide the Stabilizer Strut through the other sleeve on the other side
of the stabilizer. (diagram C)
You may have to shift the Fuselage Stabilizer Hole slightly to line up the stabilizer
strut through the hole. Shifting the Fuselage Stabilizer Hole can be accomplished
by grabbing the main fuselage hub and moving the internal fuselage strut.
Step 4
Remove the plastic end cap and spacer from the propeller axle exiting from the
front end of the fuselage. Slide on the Spinner Propeller. Place the Spinner Propeller
onto the propeller axle, then replace the spacer and the end cap.(diagram F)
Step 5
Pound Ground Stake into ground and insert non-ferruled end of Support Pole into
Ground Stake. Insert Upper Pole Section of completed Sopwith Camel Airplane
Spinner into ferrule on top of Support Pole. (diagram G)
Support Pole
Ground Stake
PLEASE NOTE: Although your Airplane Spinner is constructed with UV
resistant SunTexTM fabric, it is recommended that you take it
inside during storms and harsh weather to preserve its durability.
Landing Gear Strut
Diagonal Plastic Fitting
Landing Gear
Wheel Axle
Velcro Wing Tab
(under top wing)
Velcro Wing Tab
(under top wing)
Wing
Supports
Landing Gear Sleeves
(Please note: Landing Gear Struts must
slide into Landing Gear Sleeves.)
D
F
E
Stabilizer
Strut Internal
Fuselage
Strut
Stabilizer
Sleeve
Fuselage
Stabilizer
Hole