Prevue Pet Products 460 User manual

KEY:
L = Left panel
CT = Center-Top panel
B = Back panel
R = Right panel
F = Front panel
In = Interior pieces
T = Tray & Tray Rack
cageassemblyinstructions
Rabbit Hutch
Models: #460 | #461
#460: 36"L × 24"W × 35½"H
inte io : 31½"L × 20"W × 20"H
wi e gauge: 8 & 11
wi e spacing: 1"
#461: 46½"L × 24"W × 36¼"H
inte io : 42½"L × 20"W × 20"H
wi e gauge: 8 & 11
wi e spacing: 1"
getting starte !
READ THESE NOTES FIRST:
Assembly steps & parts lists are exactly the same for both the
#460 & #461 Rabbit Hutch models. The only difference between
models are in width and slightly in height.
• Enlist A Friend: For best results, and to guard against potential
damage to wood during assembly, this hutch requires two people.
• Count Hardware & Review All Parts: If any screws are
missing, or if parts are damaged during shipping, please contact
Prevue Customer Service immediately.
•Tools: You will need a Phillips head screw driver. We DO NOT
recommend power dr lls. Especially with wood construction,
screws can be over-tightened and the wood damaged or weakened.
Prevue is not responsible for this type of damage.
Review these instructions thoroughly before attempting to assemble
hutch. If you still require assistance, please contact Prevue Customer
Service at 800.243.3624 or [e-mail]
parts
5THIS STAGE REQUIRES TWO PEOPLE.
Center top (T1) lid panel has a
preinstalled, hinged framing piece
along the back edge. Fold the
framing piece down.
On the underside of the framing
piece is a predrilled hole, which
corresponds to the preset wood
dowel in the back (B) panel.
Have your assistant help hold the
(CT) lid. Align the hole with the
dowel and push the panels together.
At the outer corners of the framing
piece are predrilled starter holes.
Attach the (CT) lid to the side panels
with the medium-length Phillips
head screws.
8THIS STAGE REQUIRES TWO PEOPLE.
To install the locking hinge, have your
assistant hold the (CT) lid open.
→Start the in tallation with the bottom half fir t.
Locate the two starter holes on the inside
framing edge of the (R) side panel.
Using two short-length Phillips head
screws, attach the bottom half of the
locking hinge (see detail [a]).
ith the bottom half installed,
locate the starter holes on the wood
rectangle glued to the inside of the
(CT) lid. Using two short-length Phillips
head screws, attach the top half of the
locking hinge to the lid (see detail [b]).
✩Your hutch s now fully assembled!
LEFT SIDE
FRONT
BACK
RIGHT SIDE
TRAY RACK & TRAY
L
F
R
B
CT
{ 4 } long-length
Phillips head screws
for front panel
{ 6 } medium-length
Phillips head screws
for back & top
{ 4 } short-length
Phillips head screws
for interior lid hinge
{ 1 } interior lid hinge
T2
T1
In2
In1
In3
In4
R
CT
Made in China for Prevue Pet Products, Inc., Chicago IL USA www. revue et.com 800 243-3624 customerservice@revue et.com 460 | 461 — 10/11
(a)
(b)

1THIS STAGE REQUIRES TWO PEOPLE.
→A the hutch i a embled, it become very important
to have an a i tant working with you, holding panel
together while crew are in talled. Without a i tance,
piece may topple, wood may plit, and other damage
may occur — which i not the re pon ibility of Prevue.
Have your assistant hold the r ght (R) panel upright.
Rest the back (B) panel on the wood block glued to
the back of the (R) panel leg. ith your assistant
holding (B) and (R) panels together, make sure the
side edges are flush (see detail).
Note: The (B) panel will not be flu h to the top of
the ide panel ( ee Step 5).
Locate the small starter holes on the
back (B) panel. Install the medium-
length Phillips head screws in two
places, as indicated in the illustration.
Install the left (L) panel in the same
manner, again using the medium-
length screws.
2THIS STAGE REQUIRES TWO PEOPLE.
ood dowels have been preset into the outside
vertical edge of the front (F) panel. The dowels align
with predrilled holes on the inside framing edge of
the (L) and (R) side panels (see detail).
hile your assistant holds the front panel, align the
dowel posts with the predrilled holes in two places on
each side, and push the panels together. The (F) panel
will be flush at the top with the side panels.
On the outside framing edge of the
(L) and (R) panels are counterset
screw holes. Insert the long-length
Phillips screws in each of the four
holes and tighten.
steps 3Place the plastic tray (T1) into the tray rack (T2), and
slide the tray/rack unit into place.
L
B
R
L
In2
In1 In4
In3
F
R
T1
T2
4a Place the nter or wood floor (In1) panel in first,
making sure the stair-step notch faces the middle of
the cage (left) (see detail).
Place the nter or mesh floor (In2) panel in second.
4b Slide the nter or d v der doorway (In3) panel in first,
pushing it down between the channel guides, all the
way into the stair-step notch on the (In1) floor panel.
Slide the second nter or d v der (In4) panel into
place above the (In3) doorway, with the taller portion
of the panel facing the front of the hutch.
→The e divider may be left out if you de ire to create a
more open interior pace for your pet.