Prevue Pet Products 7501 User manual

INTERIOR
EXTERIOR
Deluxe
CatHome
3 Levels
Model: # 7501
read first REVIEW BEFORE ASSEMBLY
• No tools are required for assembly
•One person will be able to assemble
this deluxe at home
• For best results, follow steps in order
For assistan e or repla ement parts,
please onta t Prevue Pet Produ ts:
PHONE [phone]
ONLINE www.prevuepet. om
EMAIL ustomerservi e@prevuepet. om
7501—07/15—USL Mad in China for Prevue Pet Products, Inc., Chicago IL USA www.pr vu p t.com 800 243-3624 custom rs rvic @pr vu p t.com
1To assemble the BASE,
you will need these pieces:
2To assemble the LOWER
SECTION, you will need
these pieces:
× 4
Turn the ase over
and insert
rolling casters.
× 4 (connector rails)
Locate the four panels with short
horizontal ars along the lower edge.
Stand the side panel into the ase.
Hold the ack panel in place.
Note: Orient the panel with the thick
horizontal wires to the cage exterior.
Thinner vertical wires face the cage
interior.
Slide a connector rail down over
the two-panel seam [see Fig. 2.1 and
Fig. 2.2] until the tops are flush.
Note: The flat surface of the connector
rail faces the exterior. The rounded
surface faces the interior.
Continue around the cage,
adding the side and front panels
and attaching panels with the
connector rails.
OFF
ON
When
OFF
is up,
asters
ROLL
When
ON
is up,
asters
LOCK
T I P:
[ FIG. 2.2 ]
Showing Fig. 2.1 as
viewed from above
[ FIG. 2.1]

7501— 07/15—USL Mad in China for Prevue Pet Products, Inc., Chicago IL USA www.pr vu p t.com 800 243-3624 custom rs rvic @pr vu p t.com
3To assemble the MIDDLE
& UPPER SECTIONS,
you will need two sets
of these pieces:
4To assemble the ROOF,
you will need this piece:
× 4 (connector rails)
CLICK
The remaining panels all feature solid metal
guide ta s along the ottom wire and wire
clips on the side panels [see Fig. 3.1].
Start with the side panel. Use the guide ta s
to align it directly over the lower panel, then
clip the panels together y pressing down at the
middle (apex) of the wire clip [see Fig. 3.2].
Add the ack panel—thick horizontal wires
to the exterior, aligning directly over the
lower panel with the guide ta s—and slide a
connector rail down over the two-panel seam.
Continue around the cage, adding the
side and front panels and attaching
panels with the connector rails.
Lay the roof panel over the top and weave
the loops over and under along the top edge.
Note: From the side, the center loop will
hook UNDER the horizontal wire. The loops
to the left and right will hook OVER the
top horizontal wire.
[ FIG. 3.1]
[ FIG. 3.2]

7501— 07/15—USL Mad in China for Prevue Pet Products, Inc., Chicago IL USA www.pr vu p t.com 800 243-3624 custom rs rvic @pr vu p t.com
5To complete the cage
assembly, you will need
these pieces:
6To add the PLATFORMS,
you will need these pieces:
× 4
× 4
× 8
× 2
× 1
CLICK
To solidify the entire cage, press a connector
onto each panel intersection until it clicks
and all surfaces are flush.
“T” clips connect the intersections
along the front and ack top edge.
“+” clips connect the intersection
of panels on the front and ack.
Base lips connect the cage to the
ase. Hook the “claw” end of the
clip onto the short horizontal wire.
Press your thum into the dimple
of the clip and press down until it
clicks into the slot on the cage ase.
Hammocks and platforms may
e placed at different levels,
ut for est results, add them
to the interior at the positions
illustrated here.
For solid platforms, make sure
they clip fully into place on
the cage wires for maximum
sta ility.
★
Your cage is now fully
assem led and ready for use.