Prince Castle DHB2PT-33DQ Series User manual

541-553revC_EN Printed in USA 10/10 © 2010
BISC
SAUS
BACN
MENU
ENTER
BKFT
REG
TRANSFER
EGGS
BACN SAUSSAUS
BACN
REG
BKFT
MENU
ENTER
TRANSFER
Product Holding Bin
Product Holding Bin
DHB2PT
DHB2PT-33DQ Series -33DQ Series
Operation
Operation
Manual
Manual
355 East Kehoe Blvd. • Carol Stream, IL 60188
Phone: [phone] • Toll Free: 1-800-PCASTLE
Fax: [phone] • www.princecastle.com
LIMITED WARRANTY
This product is warranted to be free from defects in material and/or workmanship
for a period of 1 year from date of original installation, not to exceed 18 months
from the date of manufacture.
Any component which proves to be faulty in material and/or workmanship will be
replaced or repaired (at the option of Prince Castle, Inc.) without cost to the customer
for parts and labor. This warranty covers on-location service (i.e. trip charges and/or
mileage). Travel mileage is limited to 100 miles (200 Kilometers) round trip (one trip
warranty) from an authorized service agency or its sub-service agency.
This warranty is subject to the following exceptions/conditions:
• Use of any non-genuine Prince Castle parts voids this warranty.
• All labor to be performed during regular work hours. Overtime premium (the
incremental amount) will be charged to the customer.
• Damage caused by carelessness, neglect and/or abuse (e.g., dropping,
tampering or altering parts, equipment damaged in shipment, by fire, flood or
an act of God) is not covered under this warranty.
• All problems due to operation at voltages other than that specified on
equipment nameplates are not covered by this warranty. Conversion to correct
voltage is the customer’s responsibility.
• This equipment must be serviced by Prince Castle Authorized Service Agency or
a Prince Castle Service Technician during the warranty period.
TABLE OF CONTENTS
Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–9
CastleNet Communications Network . . . . . . . . . . . . . . .10
Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Parts List & Exploded View . . . . . . . . . . . . . . . . . . . . . . .13
LED Timers (tri-color)
Pan Buttons
Power On/Off Switch
Temperature Control
Panel
PRINCE CASTLE
LOGO Button
Pan & Pan Cover
Button Bar
Transfer Button
Lower Pan Displays
Upper Pan Displays MENU/ENTER
Button
BKFT (Breakfast)
LED
UP and DOWN
Arrow Buttons
REG (Regular Menu)
LED
Product Identification

Printed in USA 10/10 © 2010 541-553revC_EN
2
Product Holding Bin
DHB2PT-33DQ Series
Safety Information
Electrical Information
Prince Castle reserves the right to change specifications and product design without notice. Such revisions do not
entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased
equipment.
WARNING
Indicates information important to the proper opera-
tion of the unit. Failure to observe may result in dam-
age to the equipment and/or severe bodily injury or
death.
CAUTION
Indicates information important to the operation of
the unit. Failure to observe may result in damage to
the equipment.
Model Volts Hz Watts Amps Plug Number Agency Approval
DHB2PT-33DQ 208-240 60 2600 Max 10.8 Max NEMA L6-15P UL / cUL / UL Sanitation

3
Product Holding Bin
DHB2PT-33DQ Series
Operation
REG
BKFT
MENU
ENTER
TRANSFER
Turn power On/Off switch to ON position.
Allow 30 minutes for
heaters to reach operating
temperature. The
Temperature Display will
show temperature as unit
warms up to the operating
temperature.
Power On/Off Switch
Load pan covers (if used) onto pan racks and
insert racks into the unit.
EGGS
EGGS
MENU
ENTER
BKFT
REG
Press all PAN Buttons
The PAN DISPLAYS will show the
assigned product name.
If no product is assigned, the display
will be dim and show “----”. Pressing
the PAN button will not activate the
timer if “----” is displayed. Pressing
PAN button when product name is
displayed will start timing cycle.
BKFT (Breakfast) or
REG (Regular Menu)
will be lit depending on
pre-programmed menu.
EGGS
EGGS
MENU
ENTER
BKFT
REG
LED Timing Status When LED is steady
RED, load product
and press the PAN
Button.
(steady) = Ready for product
(flashing) = Discard product
(steady) = Oldest product, use first
(flashing) = Cook more product
(steady) = Newer product, use green first
(flashing) = Cook more product
REG
BKFT
MENU
ENTER
TRANSFER
If only one pan is active for a
product, the LED will turn from
RED to GREEN.
If no other pan is active for a
product, the LED for the first
pan loaded will turn from RED
to GREEN.
The LED for the 2nd pan (3rd
pan, etc.) loaded will turn from
RED to YELLOW.
An LED timer can be stopped
(cancelled) at any time by
pressing and releasing the
corresponding PAN Button.
LED Timers
RED
RED
RED
RED
GREEN
GREEN
GREEN
GREEN
YELLOW
YELLOW
REG
BKFT
MENU
ENTER
TRANSFER
Discard product
Cook more product
Cook more product
When any of the timer LED’s flash, cook more product or
remove and discard product as indicated.
B
SAUS
BACN
TRANSFER
BACN SAUSSAUS
6
5
3
12
4
Product, along with any remaining time, can be
transferred from one cavity to another as follows:
A. Press and release the TRANSFER
Button. Displays for available bins
are brightly lit. Displays for bins
currently timing, are dimly lit.
B. Press and release the PAN
button of the product to be
moved.
C. Press and release the
TRANSFER button again.
D. Move the product. Press and release
the PAN Button for the new location.
The new location will finish timing
the product. When the transferred
pan timing expires, location will
revert to original menu setting.
WARNING
Hot surfaces.
NOTE: If product transfer is not completed within a pre-programmed
transfer time, the transfer will be cancelled. See your Manager.
GREEN
GREEN
Flashing
YELLOW
YELLOW
Flashing
RED
RED
Flashing
541-553revC_EN Printed in USA 10/10 © 2010

4
Product Holding Bin
DHB2PT-33DQ Series
U225
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Operation (continued)
Cleaning
PROG
PROG
PROG
MENU
ENTER
BKF
REG
TRANSFER
PROG
PROG
To change a menu selection for a specific pan cavity, use the following steps:
A. Press and hold the Prince Castle Logo Button for 6 seconds. All Pan
Displays will show “PROG”. All LED Timers will be red.
D. Press the UP or DOWN Button to
scroll to the desired menu item.
B. Press and hold the MENU/ENTER Button. The display next to the
MENU/ENTER Button will display the menu choices. While holding the
MENU/ENTER button, press the UP or DOWN Buttons to scroll through the
menu choices.
C. Press a PAN Button to change the menu. The LED Timer will change to yel-
low and the Display will change from “PROG” to the assigned menu item.
F. Repeat steps A - E as required for other Pan Displays. Press
the Prince Castle Logo Button to exit the program mode.
NOTE: Up to six products may be programmed for each Pan
Button (1 for each menu). In addition, a pan may be set as “not
used” by assigning “----” as its product.
REG
BKFT
MENU
ENTER
TRANSFER
To shut down the unit, turn the power On/Off switch to OFF.
Setting Temperature
E. Press the MENU/ENTER button
to select the menu item.
1. Turn the unit off and unplug the power cord from the electrical
receptacle.
2. Remove the pan covers and pan racks. Wipe all parts and unit
with a damp cloth. DO NOT use a green scotch bright pad cleaner,
ice or water.
WARNING
Before performing any maintenance, turn the power switch to the OFF
position and unplug the power cord from the electrical receptacle.
CAUTION
This unit is not watertight. Do not clean with a water jet/jet spray.
Do not immerse the unit in water.
The unit has four shelves, each with an upper and lower heater (eight heaters total).
The factory pre-set for the upper heaters is 195°F.
The factory pre-set for the lower heaters is 185°F.
Each upper heater has a programmable range of 150° - 275°F.
Each lower heater has a programmable range of 150° - 225°F.
Use the control below and the following steps to set the setpoint temperatures for each heater.
UPPER SHELF LED
This LED will be lit to indicate
upper shelf is selected
UP/DOWN ARROW BUTTONS
Used with other buttons to scroll
through heater and temperature
selections
PRINCE CASTLE LOGO BUTTON
Press to enter
temperature selections
TEMPERATURE DISPLAY
NOTE: The unit is preset to display temperature in
Fahrenheit. To display in Celsius, press and hold
the DOWN Arrow button immediately after turning
on the power switch. To switch back to Fahrenheit,
press and hold the UP Arrow button after turning
on the power switch.
PROG LED
This LED will be lit to indicate
unit is in Program Mode
LOWER SHELF & LED
This LED will be lit to indicate
lower shelf is selected
ACTUAL TEMP BUTTON & LED
Press to display actual temperature for the
selected heater. LED will be lit when actual tem-
perature is displayed.
SETPOINT BUTTON & LED
Press to display setpoint temperature of a
selected heater. LED will be lit when setpoint
temperature is displayed.
NOTE: To reset all times and temperatures to the factory settings, turn the unit off, then press and hold the UP and DOWN arrow buttons
simultaneously while turning the unit back on. A “P” will appear in the display and all times and temperatures will be reset to original factory settings.
1
8
7
Printed in USA 10/10 © 2010 541-553revC_EN

Product Holding Bin
DHB2PT-33DQ Series
U220
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
U225
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
U225
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Setting Temperature (continued)
Press the UP or DOWN Arrow Buttons until the desired shelf
LED and upper (U) or lower (L) heater is selected.
Press and hold the SETPOINT Button and the Prince Castle
Logo Button for 5 seconds. The Program LED will light.
Calibrating Heaters
If calibration is necessary use
the following steps:
NOTE: Allow sufficient amount of
time for temperatures to stabilize
before starting calibration.
Press the UP or DOWN Arrow
Buttons until the desired shelf LED
and upper (U) or lower (L) heater is
selected.
Take a temperature reading within the shelf near the center of
the heater surface.
Use a standalone temperature meter (not supplied).
Press the UP or DOWN Arrow Buttons until the desired
setpoint temperature is displayed
U2:30
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
U225
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Press and hold the PRINCE CASTLE
LOGO and ACTUAL Buttons for 5
seconds. The semi-colon (:) LED
indicator will light. The temp dis-
played is the actual heater tempera-
ture sensed by the controller.
U2:20
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Press the UP or DOWN Arrow
Buttons until the temperature
displayed matches the reading
obtained in Step 2.
Press the PRINCE CASTLE
LOGO Button to save the
temperature value and exit the
Calibration Mode.
Press the Prince Castle Logo Button to save the new setpoint
value. Repeat steps 2—5 to change the setpoint for any other
heater.
WARNING
Hot surfaces. Use
caution when taking
temperature readings
within the shelf
U220
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
U2:30
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
To clear any offset
readings, press the
SETPOINT Button.
U220
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
34
1
23
45
2
5
541-553revC_EN Printed in USA 10/10 © 2010

Selecting Breakfast and Regular Menus
MNU1
⇑
MENU
ENTER
BKFT
REG
⇑
PROG
WBUN
MENU
ENTER
BKFT
REG
Programming the Menus
PROG
PROG T
MNU1
⇑
MENU
ENTER
BK
REG
⇑
There are six menus available:
BKFT LED ON = Menu1 or Menu6
REG LED ON = Regular2, Regular3, Regular4, or Regular5
Press and hold the MENU/ENTER button, then use the UP or
DOWN Arrow button to scroll through the 6 menus.
Press and hold the MENU/ENTER button, the display next to
the MENU/ENTER button will show the menu choices. Use
the UP or DOWN Arrow button to scroll through the 6 menus.
Release the MENU/ENTER button when the desired menu is
displayed.
When the MENU/ENTER button is released, all displays will
again show PROG
..
Press and hold the PRINCE CASTLE LOGO button
(on the button bar) until all the displays show PROG
and the PAN buttons LED’s all glow red.
A. Press the PAN button next to the display to be changed.
The LED will change from red to yellow and the display will
change from PROG to the assigned menu item.
When scrolling, menu numbers appears in this display.
MNU1
⇑
MENU
ENTER
BKFT
REG
⇑
R
When the desired menu is displayed, release the
MENU/ENTER button. The food products for the menu will be
displayed in the upper and lower PAN displays.
When timers for a different menu are still active,
those BKFT or REG LED’s will flash until they are all cancelled.
----
PROG T
A. Repeat Steps 2 & 3 as required.
B. Press the PRINCE CASTLE LOGO button to exit the
Programming Mode and return to the Run Mode.
NOTE: Up to six items (one for each menu) may be programmed
for each tray button. A tray may be set as “not used” by
assigning “
---- ” as its product.
PROG
PROG
MENU
ENTER
B
R
PROG
SBUN
MENU
ENTER
BKF
REG
B. Press the UP or DOWN Arrow buttons to scroll to the desired menu
item.
C. Press the MENU/ENTER button to save the selection. All displays
will show PROG.
Product Holding Bin
DHB2PT-33DQ Series
2
2
1
1
34
Printed in USA 10/10 © 2010 6 541-553revC_EN

⇑
⇑
TIME
PROD
MENU
ENTER
BKFT
REG
TRANSFER
ENTR
SET
Product Holding Bin
DHB2PT-33DQ Series
⇑
⇑
:07
EGGS
MENU
ENTER
TRANSFER
ENTR
COOK
⇑
⇑
2:00
EGGS
MENU
ENTER
TRANSFER
ENTR
HOLD
⇑
⇑
TIME
PROD
MENU
ENTER
TRANSFER
ENTR
SET
Changing the Hold & Cook-More Times
⇑
⇑
TIME
EGGS
MENU
ENTER
TRANSFER
ENTR
A. Press and release the MENU/ENTER button to enter the
Set Product Time menu. The display will show, for example,
SET EGGS TIME ⇑ ⇓ ENTR..
A. The display now shows the current hold time.
A. The display will show SET PROD TIME ⇑ ⇓ ENTR..Repeat Steps 2
– 4 for any other product.
B. Press and release the PRINCE CASTLE LOGO button at any
time to exit the Programming Mode and return to the Run Mode.
NOTE: If the MENU/ENTER button has not been pressed to save any
changes, the program will revert to the original values.
A. The display will now show current Cook-More time..Use the
UP or DOWN Arrow button to scroll to the desired cook -
more time.
B. Use the UP or DOWN Arrow button to scroll to the desired
hold time. When the desired hold time is displayed, press
the MENU/ENTER button to save the desired hold time.
NOTE: Hold time cannot be reduced to less than the Cook-More
time plus one minute.
NOTE: Cook-More time cannot be increased to more than the
Hold time minus one minute.
⇑
⇑
2:10
EGGS
MENU
ENTER
TRANSFER
ENTR
HOLD
B. When the desired cook-more time is displayed, press the
MENU/ENTER Button to save it.
⇑
⇑
:10
EGGS
MENU
ENTER
TRANSFER
ENTR
COOK
NOTE: Holding the UP or DOWN Arrow Buttons for longer than 2
seconds will cause the product list to automatically scroll up or down.
B. Use the UP or DOWN Arrow button to scroll through the list
of products. When the desired product is displayed, press
the MENU/ENTER button to select it.
2
45
1
3
A. The SET PRODUCT TIME menu is used to change the Hold & Cook-More times.
B. Press and hold the PRINCE CASTLE LOGO button, then immediately press and hold the MENU/ENTER button until the display shows one
of three programming menus.
C. Use the UP or DOWN Arrow button to scroll to the SET PROD TIME ⇑ ⇓ ENTR menu.
PRINCE CASTLE LOGO Button
MENU/ENTER Button
Up & Down arrow Buttons
Product
Cook-More Time
7
541-553revC_EN Printed in USA 10/10 © 2010

Product Holding Bin
DHB2PT-33DQ Series
Changing Product Names
⇑
⇑
WXP1
PROD
MENU
ENTER
BKFT
REG
TRANSFER
ENTR
⇑
⇑
NAME
PROD
MENU
ENTE
ENTR
⇑
⇑
NAME
PROD
MENU
ENTER
BKFT
REG
TRANSFER
ENTR
EDIT
⇑
⇑
EXP1
PROD
MENU
ENTER
BKFT
REG
TRANSFER
ENTR
A. The EDIT PRODUCT NAME menu is used to change a default product name to one of your own choosing.
B. Press and hold the PRINCE CASTLE LOGO button, then immediately press and hold the MENU/ENTER button until the display shows one
of four programming menus.
C. Use the UP or DOWN Arrow button to scroll to the EDIT PROD NAME ⇑ ⇓ ENTR Menu.
NOTE: The default names available for editing are listed on page 8.
A. Press and release the MENU/ENTER button to enter the
Edit Product Name menu.
The display will read SEL PROD XXXX ⇑ ⇓ ..
B. Use the UP or DOWN Arrow button to scroll through the list of
products.
C. When the desired product is displayed, press the
MENU/ENTER button to select it. The first letter (in this case,
the EE) will start blinking.
A. The display will show EDIT PROD NAME ⇑ ⇓ . Repeat Steps
2–4 for any other product.
B. Press and release the PRINCE CASTLE LOGO button at
any time to exit the Programming Mode and return to the
Run Mode.
NOTE: If the MENU/ENTER button has not been pressed to save
any changes, the program will revert to the original names.
A. To change the blinking E, use the UP or DOWN Arrow button
to scroll to the desired letter/number/symbol.
B. When the desired selection is displayed, press the PAN
button (to the left or right of the selected display) to move
to the next digit.
C. Repeat for all digits.
NOTE: Holding the UP or DOWN Arrow Buttons for longer than 2
seconds will cause the selected digit to automatically scroll up or
down.
⇑
⇑
WXP1
PROD
MENU
ENTER
ENTR
When all four digits have been changed, press the MENU/ENTER
button to save the new name.
PRINCE CASTLE LOGO Button MENU/ENTER Button
23
1
54
Printed in USA 10/10 © 2010 8 541-553revC_EN

Product Holding Bin
DHB2PT-33DQ Series
Set Maximum Transfer Time
.20
XFR
TRANSFER
MAX
A. Press and release the MENU/ENTER Button to enter the
Set Maximum Transfer Time menu.
B. The display shows MAX XFR :20 ⇑ ⇓ ENTR . This shows a
value of 20 seconds.
.25
XFR
TRANSFER
MAX
A. To change the time, use the UP or DOWN Arrow Button to
scroll to the desired time. When the desired selection is dis-
played, press the MENU/ENTER Button to enter the selection.
B. Press and release the PRINCE CASTLE LOGO Button at any
time to exit the Programming Mode and return to the Run
Mode.
NOTE: If the MENU/ENTER Button has not been pressed to save any
changes, the program will revert to the original time.
⇑
⇑
TIME
XFR
MENU
ENTER
BKFT
REG
TRANSFER
ENTR
MAX
A. The SET MAXIMUM TRANSFER TIME menu is used to set the amount of time allowed to make a product transfer from one pan to another.
B. Press and hold the PRINCE CASTLE LOGO Button, then immediately press and hold the MENU/ENTER Button until the display shows one
of four programming menus.
C. Use the UP or DOWN Arrow Button to scroll to the MAX XFR TIME ⇑ ⇓ ENTR (Set Maximum Transfer Time) Menu.
PRINCE CASTLE LOGO Button MENU/ENTER Button
1
23
9
541-553revC_EN Printed in USA 10/10 © 2010

Product Holding Bin
DHB2PT-33DQ Series
CastleNet® Communications Network
The Prince Castle DHB-BK Bins and Retro Bun Timer and New Bun
Cabinet Timers can be inter-connected to form the CastleNet®
Communication Network. The network can be used for data transfer
between bins and timers for menu updates or to transfer product hold
time from bin-to-bin. A PDA (or similar device) or a notebook with Prince
Castle MenuView®software is used to connect to the network and enter
the desired changes.
Each bin is supplied with a standard 25' cable and allows units to be
“daisy-chained” together to form the network. If cable is too short, use
Prince Castle Extender Cable Kit, P/N PC-COMEXT.
The factory default address for Main bins and timers is address 1.
The factory default address for Specialty bins and timers is address 2.
If a third bin is used, the address must be set at 3.
The factory default address for the Retro Bun Timer is bunF.
IN OUT
EXTERNAL
IN OUT
EXTERNAL
IN OUT
EXTERNAL
RETRO
BUN
TIMER
BIN 1 BIN 2 BIN 3
Telephone jack plugs are located on the back of the unit.
Connect the units using the cables provided as shown here.
Bin 1 Bin 2 Bin 3
IMPORTANT: Each timer must have a different address.
If a location has three bins, it is recommended that the bins
and timers be set consecutively to addresses 1 through 3.
A. Turn the power switch off, wait 15 seconds. Turn the switch
to ON while pressing and holding the ACTUAL and SET-
POINT buttons. The display will show the current bin
address.
B. Continue to hold the buttons until PROG LED turns on.
prog
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
bar3
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Available addresses are:
bin1 thru bin9, binA, binB, binC, binD, binE
and binF.
IMPORTANT: Continue to step 5 to
check the timer address. No two
timers can have the same address.
Use the UP or DOWN Arrow buttons to scroll to the desired
address. Press the PRINCE CASTLE LOGO Button to store the
new address.
EGGS
EGGS
EGGS
MENU
ENTER
B
RE
TRANSFER bar2
To check the timer address, press and hold the PRINCE
CASTLE LOGO button and the DOWN Arrow button.
The current timer address will be displayed in the far right timer
display.
To change the timer address, proceed to step 6.
⇑
⇑
ADDR
SET
MENU
ENTER
TRANSFER
bar2
To change the timer address, turn the unit power switch off and
wait 15 seconds. Turn the power switch back on and immedi-
ately press and hold the PRINCE CASTLE LOGO button and the
DOWN Arrow button for approximately 6 seconds or until the
display shows SET ADDR ⇑ ⇓ BAR2.
The address number will blink on/off.
⇑
⇑
ADDR
MENU
ENTER
BKFT
REG
bar3
Use the UP or DOWN Arrow button to scroll to the desired
address. Press the MENU/ENTER button to store the new
address and return to normal operating mode.
Available addresses are:
bin1 thru bin 9, binA, binB, binC, binD, binE and binF.
bar2
UPPER
PROG
LOWER
ACTUAL
TEMP
SET-
POINT
Example
Example
6
45
7
2
1
3
Printed in USA 10/10 © 2010 10 541-553revC_EN

Product Holding Bin
DHB2PT-33DQ Series
Factory Presets
Product Menu Detail
Product Display Hold Cook-More
Name Minutes1Minutes1
Hamburger BGR1 30 3
Hamburger BGR230 3
Hot Dog 10:1 DOG1 30 3
Hot Dog Foot Long DOG2 30 3
Grilled Chicken GRCK 30 3
Breaded Chicken BRCK 30 3
Chicken Strip STRP 30 3
Gravy GRVY 30 3
Chili Hot Dog Sauce CHLI 30 3
Bacon BACN 30 3
Special #1 SPC1230 3
Special #2 SPC2230 3
Special #3 SPC3230 3
Special #4 SPC4230 3
Special #5 SPC5230 3
Special #6 SPC6230 3
Special #7 SPC7230 3
Special #8 SPC8230 3
Special #9 SPC9230 3
Special #A SPCA230 3
Special #B SPCB230 3
Special #C SPCC230 3
Special #D SPCD230 3
Special #E SPCE230 3
Special #F SPCF230 3
1. Hold and Cook-More times may be re-programmed. See page 7.
2. Product abbreviations EXP1 through EXPF may be reprogrammed. See page 8.
11
541-553revC_EN Printed in USA 10/10 © 2010

Product Holding Bin
DHB2PT-33DQ Series
Troubleshooting
Wiring Diagram
Display flashes Opn & rEL.
Display flashes SHr & rEL.
Display flashes Opn & rEL.
Display shows HHH for an extend-
ed period of time and heater sur-
face temperature is hot.
Display shows HHH for an extend-
ed period of time and heater sur-
face temperature is cool.
Open relay. Circuit inoperable.
Shorted relay. Circuit inoperable.
Open heater.
Unplugged ribbon cable between
power and main circuit boards.
Temperature is below 75°F.
Heater inoperable.
Probe inoperable.
Relay inoperable.
Temperature is above 300°F
(abnormal operation).
Probe is inoperable.
Replace power circuit board.
Replace power circuit board.
Test heater resistance (150.2 Ohms).
Replace heater if necessary.
Verify ribbon cable connection.
Normal display during warmup.
Test heater resistance (150.2 Ohms).
Check for open thermocouple wires from probe.
Replace heater/probe assembly.
Replace power circuit board.
Diagnostic circuit inoperable. Replace power
circuit board.
Check for pinched thermocouple wires from
probe. Replace heater/probe assembly.
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Printed in USA 10/10 © 2010 12 541-553revC_EN

Product Holding Bin
DHB2PT-33DQ Series
Parts List & Exploded View
1
21
18
25 24
20
23
26
19
28 11
87
6
2
1
9
10
12
18
17
13
14
4
15
16
15
19
3
1 541-316 Side Panel
2 541-389S Main P. C. Board Kit
3 541-318 P.C. Board Bracket
4 541-317 Right Side Insulation
5 541-326 Wire Chase
6 541-333S Display P.C. Board Kit
7 89-955 Spacer
8 541-353S Overlay and Bracket Kit
9 86-118 Modular Coupling
10 541-320 Hold Down Bracket
11 78-184S Power Switch
12 88-609 Power Inlet
13 72-200-25S Power Cord Kit
14 76-724 Screw, Socket, 8-32 x 3/4
15 541-359S Lower Heater Assy (230 Volt)
16 541-376S Upper Heater Assy (230 Volt)
17 541-489 Chassis, Right
18 541-129 Side Cover Bracket
19 541-369 Insulation
20 541-329 Top Cover
21 541-324 Header
22 541-650 Trim
23 541-383 Shelf Bracket
24 541-488 Chassis, Left
25 541-317 Insulation
26 541-606 Base
27 197-232 Foot
28 541-323 Bottom Cover
* 541-479 Black Pan Covers (Not Shown)
* PC-COMEXT Cable, Prince Castle (Not Shown)
* TBD Cable, K-Mart (Not Shown)
* TBD Cable, Target (Not Shown)
* TBD Cable, Wal-Mart (Not Shown)
* 940-0504 Cable, Radio Shack (Not Shown)
279-423
Ref. Part No. Description Ref. Part No. Description
13
541-553revC_EN Printed in USA 10/10 © 2010

Product Holding Bin
DHB2PT-33DQ Series
NOTES
Printed in USA 10/10 © 2010 14 541-553revBC_EN