Prince Castle Potato Witch 913 User manual

OPERATING
INSTRUCTIONS
Potato Witch®
Model No. 913, 914 & 915
355 East Kehoe Blvd. l Carol Stream, IL 60188
Tel: [phone] l Fax: [phone]
Toll Free: 1-800-PCASTLE
Printed in 1999
Prince Castle Inc. 913-505
Prince Castles Potato Witch® cuts potatoes and
other vegetables with ease. single stroke pro-
duces shoestring-style or steak-cut fries. Fast and
easy, the Potato Witch® provides superior leverage
for a superior performance. Designed for safe, heavy-
duty commercial use. Sturdy frame with base and
1/2 guide rods. Precision sharp, stainless steel
blades and two handles give perfect balance for easy
cutting.
PRODUCT SPECIFICATION
Model No. 913:
3/8 Square cut
Model No. 914: Six-section wedge (steak fries)
Model No. 915: Eight-section wedge (steak fries)
Height 17 (43.2 cm)
Width 8 (20.3 cm)
Length 10 (25.4 cm)
Shipping Weight: 12 lbs. (5.44 kg)
LIMITED WARRANTY
This product is warranted to be free from defects in
material and/or workmanship for a period of two (2)
years from the date of original installation, not to
exceed 30 months from the date of shipment from
our factory with the exception of the blades.
Blades are warranted to be free from defects at time
of delivery only.
ny component which proves to be faulty in material
and/or workmanship will be replaced or repaired (at
the option of Prince Castle, Inc.) without cost to the
customer for parts or labor.
This warranty is subject to the following exceptions/
conditions:
lThis equipment is portable; charges for on-loca-
tion service (e.g., trip charges, mileage) are not
included in the provisions of this warranty.
lDamage caused by carelessness, neglect, and/
or abuse (e.g., dropping, tampering or altering
parts), equipment damaged in shipment, by fire,
flood or an act of God is not covered under this
warranty.
lBlades are warranted to be free from defects in
material and/or workmanship ato timeof delivery
only.
TABLE OF CONTENTS PAGE
Installation................................................................... 2
Operating ..................................................................... 2
Cleaning ...................................................................... 2
Parts Identification ..................................................... 3

INSTALLATION
1. fter you remove the Potato Witch® from the
carton, inspect the unit for signs of damage. If
there is damage to the unit:
lNotify carrier within 24 hours after delivery.
lSave carton and packing materials for inspection
purposes.
lContact your local Prince Castle dealer or if
purchased directly, the Prince Castle Customer
Sales Department at 1-800-722-7853 to arrange
for a replacement.
lll inoperable warrany parts must be returned to
the Service Center.
CAUTION: Blades are extremely sharp.
2. To mount Potato Witchâ directly to the wall, hold it
up against the wall in the selected mounting area,
and mark the two holes for correct drilling location.
3. Using a 5/16 drill bit, drill the two marked holes and
fill with a
5/16 anchor mount. Mount the Potato
Witchâ to the wall with the provided flat head
screwdriver.
4. The Potato Witchâ can also be mounted to an
optional wall mounting plate (913-5) which can be
purchased from Prince Castle.
5. Place the mounting plate against the wall and mark
the two outside holes with a pencil.
6. Drill the holes using a 3/8 drill bit. Put a 7/16
anchor into the wall.
7. Put the two
5/16 flat head screws through the back
of the mounting plate. Mount the mounting plate to
the wall using two
7/16 flat head screws.
8. Line up the Potato Witchâ mounting plate with the
two flat head screws, and tighten with wing nuts
provided.
OPERATION
1. With your right hand, raise pusher handle to the
extreme upright position. Using a fork, place
product on blades. See figure 1.
2. Grasp handle at base of potato witch, with left
hand. Bring the pusher head handle downward in
one quick, firm stroke. See figure 2.
MAINTENANCE
1. Lubricate guide rods daily.
2. Tighten blades daily with hex head wrench pro-
vided.
IMPORTANT: Loose blades can cause damage to the
blades and the pusher head.
CLEANING
1. Immerse unit into hot soapy water, using spray if
available, rinse thoroughly. Spray wash unit.
2. Rinse thoroughly. Let air dry.
IMPORTANT: Use Prince Castle model number 912-
107 cleaning brush.
CAUTION: Clean blades from re erse side.
figure 1
figure 2
2

-
PARTS LIST
ITEM PART NO. DESCRIPTION
1 913-5 Wall Mounting Plate (Optional)
2 913-6 Base
3 913-15 Slide plate
4 913-14 Guide od (914 & 915)
913-35 Guide od (913)
5 912-34 Connecting Link Left
912-35 Connecting Link ight
6 910-17 Guide od Cushion (Pkg of 2)
7 913-21 Pusher Head (913)
8 913-36 Blade Frame (913)
9 911-114 Handle
10 913-1 eplacement Blade Set
11 912-8 Pusher Handle
12 914-5 Blade Frame (914 & 915)
13 908-1 eplacement Blade Set (8 Sec) (915)
914-1 eplacement Blade Set (6 Sec) (914)
14 915-2S Pusher Head (8 Sec) (915)
914-6 Pusher Head (6 Sec) (914)
15 919-18 Feet (Pkg of 4) Not Shown
ITEM PART NO. DESCRIPTION
A 76-493 Flat Head Screw 5/16 -18 X 11/4
(Part of 913-5)
913-20 Wing Nut (Part of 913-5)
B 76-202 Set Screw 1/4-20 X 1/4
C 919-19 Top Pivot Pin 1/4-20 X 31/4
73-142 Self Locking Nut
D 912-15 Middle Pivot Pin1/4-20 X 41/2
73-142 Self Locking Nut
E 76-242 Socket Hd. Cap Screw 1/4-20
79-132 Flat Washer 1/4
F 911-15 Socket Hd Cap Scr 1/4-20
(Pak of 12) (913 only)
H 76-534 Bottom Pivot Pin 1/4-20
73-142 Self Locking Nut
J 76-529 Screw 6-32 X 3/4 (914 & 915)
3