Pro-Form PFEL75907.0 User manual

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manu-
al for future reference.
Serial Number
Decal
(beneath frame)
Model No. PFEL75907.0
Serial No.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
USER’S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction.If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–5 p.m. MST
ON THE WEB:
www.proformservice.com

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
2
PROFORM is a registered trademark of ICON IP,Inc.

3
IMPORTANT PRECAUTIONS
WARNING:To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser. Use the ellipti-
cal exercise only as described in this
manual.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under age 12 and pets away
from the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 275 lbs.
(124 kg).
8. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. Hold the handgrip pulse sensor or the han-
dlebars when mounting, dismounting, or
using the elliptical exerciser.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
11. Keep your back straight while using the ellip-
tical exerciser; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
14. The decal shown below has been placed on
the elliptical exerciser.If the decal is miss-
ing or illegible, call the toll-free telephone
number on the front cover of this manual
and order a free replacement decal. Apply
the decal in the location shown.
WARNING:Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
246724
246723
210124
2246722
2

4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary
PROFORM®CROSSTRAINER 600 elliptical exerciser.
The CROSSTRAINER 600 elliptical exerciser pro-
vides a wide array of features designed to make your
workouts at home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, please
note the product model number and serial number
before contacting us. The model number is
PFEL75907.0. The serial number can be found on a
decal attached to the elliptical exerciser (see the front
cover of this manual for the location of the decal).
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.proformservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handgrip Pulse Sensor
Handlebar
Wheel
Pedal
Console
Water Bottle Holder*
Accessory Tray
Leveling Foot
Leveling Foot
Fan
*No water bottle is included

5
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a Phillips screwdriver , an adjustable
wrench , and a rubber mallet .
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST on pages 24 and 25. The number follow-
ing the parentheses is the quantity needed for assembly. Note: Some small parts may have been preassem-
bled. If a part is not in the parts bag, check to see if it has been preassembled.
M8 Split
Washer (72)–2
M8 x 48mm Button
Screw (78)–2
M4 x 16mm
Self-tapping
Screw (79)–10
M8 x 42mm Bolt
(71)–4
M10 x 20mm x
1mm Washer
(81)–2
M10 x 20mm x
1.5mm Washer
(84)–2
M4 x 16mm
Screw (86)–4
M10 Spacer
(76)–2
M6 x 35mm Phillips
Screw (87)–8
M6 Split
Washer (88)–8
M10 x 23mm Shoulder
Screw (80)–8
M10 x 62mm Bolt (89)–4 M10 x 78mm Button Screw (90)–2
M10 x 20mm Button
Screw (91)–4
M10 x 20mm x
2mm Washer
(92)–4
M4 x 13mm
Washer (93)–2
M10 x 25mm
Washer (94)–4
M8 x 16mm Button
Screw (95)–3
M8 Nylon
Locknut (96)–4 M10 Nylon Locknut (97)–2
Wave Washer
(98)–8
Star Washer
(100)–3

6
1.
Orient the the Front Stabilizer (35) as shown.
Attach the two Wheels (25) to the Front Stabilizer
with two M10 x 62mm Bolts (89) and two M10
Nylon Locknuts (97).
Attach two Feet (26) to the underside of the
Front Stabilizer (35).
2. Have a second person tip the Frame (2) back-
ward. Attach the Front Stabilizer (35) to the
Frame with two M10 x 78mm Button Screws (90).
97
26
26
1
2
2
89
89
25
25
35
90
35
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical exerciser.

7
4. Have a second person hold the Upright (6) near
the Frame (2) as shown.
Pull the Wire Harness (48) out of the Frame (2)
and insert it upward through the Upright (6). Do
not let the Wire Harness fall into the Upright; use
apiece of tape or an elastic band to hold the
Wire Harness in place until step 12.
Insert the Upright (6) into the Frame (2). Attach
the Upright with three M8 x 16mm Button Screws
(95) and three Star Washers (100). Avoid pinch-
ing the Wire Harness (48) between the
Upright and the Frame.
6
4
95
95
100
2
95
100
48
3. Orient the Base (1) near the Frame (2) as
shown. See the inset drawing. Attach two Feet
(26) to the underside of the Base.
Have a second person tip the Frame (2) forward.
Insert the Base (1) into the Frame. Attach the
Base with two M10 x 62mm Bolts (89), two M10
Spacers (76), two M8 x 48mm Button Screws
(78), and two M8 Split Washers (72).
2
89
1
72
78
3
1
76
26
26

8
5. Identify the Left Roller Leg (12), which is marked
with a “Left” sticker. Orient the Left Roller Leg as
shown near the left Crank Arm (36).
Apply a small amount of the included grease to
both sides of a Wave Washer (98). Also, apply
grease to the Roller (22) on the Left Roller Leg
(12); spread the grease evenly around the
Roller.
Slide the Wave Washer (98) onto the left Crank
Arm (36). Next, slide the Left Roller Leg (12)
onto the Crank Arm and set the Roller (22) on
the Base (1). Attach the Left Roller Leg with an
M10 x 23mm Shoulder Screw (80), an M10 x
20mm x 1.5mm Washer (84), and a Crank Axle
Cap (30).
Repeat this step to attach the Right Roller
Leg (21) to the right Crank Arm (not shown).
536
1
84 30 98
22
Grease
8012
21
6. Identify the Left Handlebar (8), which is marked
with a “Left” sticker.Insert the Left Handlebar into
one of the Handlebar Legs (11) as shown.
Attach the Left Handlebar (8) with two M8 x
42mm Bolts (71) and two M8 Nylon Locknuts
(96). Make sure that the Nylon Locknuts are
inside the hexagonal holes.
Assemble the Right Handlebar (not shown)
and the other Handlebar Leg (not shown) in
the same way.11 71
Grease
8
96
6
Hexagonal
Hole
Hexagonal
Hole

9
7. Position an Inner Handlebar Cover (18) and an
Outer Handlebar Cover (19) around the Left
Handlebar (8) as shown.
Attach the Inner and Outer Handlebar Covers
(18, 19) with three M4 x 16mm Self-tapping
Screws (79) and an M4 x 13mm Washer (93).
Start all three Self-tapping Screws before
tightening them.
Repeat this step for the Right Handlebar (not
shown).
7
8. Apply a generous amount of grease to the Pivot
Axle (65) and insert it into the Frame (2).
Attach the two Frame Covers (17) to the Frame
(2) with four M4 x 16mm Screws (86) as shown.
886
86
65
17
17
2
19
18 79
79
8
93
Grease
9. Apply a small amount of grease to both sides of
a Wave Washer (98). Slide the Wave Washer
onto the left side of the Pivot Axle (65). Next,
slide the Left Handlebar (8) onto the Pivot Axle
as shown.
Attach the Left Handlebar (8) with an M10 x
23mm Shoulder Screw (80) and an M10 x 20mm
x1mm Washer (81).
Repeat this step to attach the Right
Handlebar (9) to the Pivot Axle (65).
9
98
9
81
8
80
65
Grease

10
10.Identify the Left Pedal (13) and the Left Pedal
Leg (14), which are marked with “Left” stickers,
and orient them as shown.
Attach the Left Pedal (13) to the Left Pedal Leg
(14) with four M6 x 35mm Phillips Screws (87)
and four M6 Split Washers (88). Start all four
Phillips Screws before tightening them.
Repeat this step to attach the Right Pedal
(not shown) to the Right Pedal Leg (not
shown).
10
88 88
13
14
87
87
11. Apply a generous amount of grease to two Pedal
Leg Axles (32). Insert one Pedal Leg Axle into
the bottom of the left Handlebar Leg (11). Insert
the other Pedal Leg Axle into the Left Roller
Leg (12).
Apply a small amount of grease to both sides of
two Wave Washers (98). Place a Wave Washer
on each Pedal Leg Axle (32).
Orient the Left Pedal Leg (14) as shown, and
slide it onto the Pedal Leg Axles (32). Attach the
Left Pedal Leg to the left Handlebar Leg (11) with
two M10 x 23mm Shoulder Screws (80), two
M10 x 20mm x 2mm Washers (92), and two Axle
Caps (31).
Attach the Left Pedal Leg (14) to the left Roller
Leg (12) with two M10 x 20mm Button Screws
(91) and two M10 x 25mm Washers (94); do not
overtighten the Button Screws. The Legs (11,
14, 21) must be able to pivot freely.
Repeat this step for the Right Pedal Leg (not
shown).
92
91
14 94
80
31
32
31
11
80
12
94 91
92 32
11
Grease
98
Grease
98

11
12. The Console (5) requires four 1.5V “D” batteries
(not included); alkaline batteries are recommend-
ed. IMPORTANT: If the elliptical exerciser has
been exposed to cold temperatures, allow it
towarm to room temperature before insert-
ing batteries into the Console. If you do not
do this, the displays or other electronic com-
ponents may become damaged.
See the inset drawing. Remove the battery cover
from the Console (5) and insert four batteries
into the Console. Make sure that the batteries
are oriented as shown by the diagram in the
battery compartment. Then, reattach the bat-
tery cover.
Note: The Console (5) can be operated with an
optional power supply instead of batteries. To
purchase a power supply, call the toll-free
telephone number on the front cover of this
manual. Plug one end of the power supply into
the jack on the console. Plug the other end of
the power supply into an appropriate outlet that
is properly installed in accordance with all local
codes and ordinances.
Have a second person hold the Console (5) near
the Upright (6) as shown. Connect the console
wire to the Wire Harness (48). Insert the excess
wire downward into the Upright.
Attach the Console (5) with four M4 x 16mm
Self-tapping Screws (79).
13. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
12
5
5
Battery Cover
Console
Wire
48
6
79

12
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO MOVE THE ELLIPTICAL EXERCISER
Due to the size and weight of the elliptical exercis-
er, moving it requires two persons. Stand in front of
the elliptical exerciser, hold the upright, and place one
foot against one of the front wheels. Pull on the upright
and have a second person lift the base until the ellipti-
cal exerciser will roll on the front wheels. Carefully
move the elliptical exerciser to the desired location,
and then lower it to the floor.
HOW TO LEVEL THE ELLIPTICAL EXERCISER
If the elliptical
exerciser
rocks slightly
on your floor
during use,
turn one or
both of the lev-
eling feet
beneath the
base or
beneath the front stabilizer until the rocking motion is
eliminated.
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lower position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The crank arm covers can turn in either direction.
It is recommended that you turn the crank arm
covers in the direction shown by the arrow below;
however, for variety, you can turn the crank arm
covers in the opposite direction.
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary,step off the higher
pedal first. Then, step offthe lower pedal.
Place
your foot
here
Pull on
upright
Leveling
Feet
Lift here
Pedals
Crank Arm
Cover
Handlebars

13
FEATURES OF THE CONSOLE
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you select the manual mode of the console, you
can change the resistance of the pedals with the touch
of a button. As you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the handgrip pulse sensor.
The console also features five interactive cross train-
ing programs designed to help you to burn calories
and enhance your cardiovascular system while toning
and strengthening your muscles. The cross training
programs automatically control the resistance of the
pedals and prompt you to perform a variety of strength
exercises during your workout. Choose an upper body,
lower body, or whole body cross training program to
focus your workout. Note: The strength exercises
require the use of dumbbells and an inflatable exercise
ball (not included). To purchase dumbbells or an
exercise ball, call toll-free 1-888-533-1333.
You can also use four calorie goal programs designed
to help you burn 300 or 400 calories in 25, 30, or 45-
minute workouts. The calorie goal programs automati-
cally control the resistance of the pedals and prompt
you to increase or decrease your pace while counting
the calories you burn.
The console also offers a high performance program
and a heart rate control program. The high performance
program automatically changes the resistance of the
pedals and prompts you to increase or decrease your
pace as it guides you through an effective workout. The
heart rate control program changes the resistance of
the pedals and prompts you maintain a steady pace to
keep your heart rate near a target heart rate while you
exercise.
To use the manual mode of the console,follow the
steps beginning on page 14. To use a cross training
program,see page 16. To use a calorie goal pro-
gram,see page 18. Touse the high performance
program, see page 19. To use the heart rate control
program,see page 20.
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic.

14
HOW TO USE THE MANUAL MODE
Press the Resistance decrease button or
begin pedaling to turn on the console.
A moment after you turn on the console, the dis-
play will light.
Select the manual mode.
Each time you turn on the console, the manual
mode will be selected automatically. If you have
selected a program, reselect the manual mode by
pressing the Programs button repeatedly until the
words MANUAL MODE appear in the top of the
display.
Begin pedaling and change the resistance of
the pedals as desired.
As you pedal, change the resistance of the ped-
als by pressing the Resistance increase and
decrease buttons repeatedly. There are ten resis-
tance levels. Note: After you press the buttons, it
will take a moment for the pedals to reach the
selected resistance level.
Follow your progress with the display.
The left side of the
display—The left
side of the display
will show the elapsed
time. Note: When a
program is selected,
the display will show the time remaining in the
program instead of the elapsed time. An exception
is the heart rate control program, which shows the
elapsed time.
The left side of the display will also show your
heart rate when you use the handgrip pulse sen-
sor (see step 5 on page 15).
When a program is selected, the left side of the
display will also show the approximate number of
calories you have burned.
The center of the
display—When you
select the manual
mode, the center of
the display will show a
track that represents
640 revolutions. As you exercise, indicators will
appear in succession around the track until the
entire track appears. The track will then disappear
and the indicators will again begin to appear in
succession.
The center of the dis-
play will also show the
resistance setting of
the pedals for a few
seconds each time the
resistance setting
changes.
The right side of the
display—The right
side of the display will
show the distance
(total revolutions) you
have pedaled and
your pedaling pace, (revolutions per minute [rpm]).
The top of the display—When you select the
manual mode, the top of the display will show the
approximate number of calories you have burned
and the approximate number of grams of carbs
you have burned.
You can change the display color if desired. Press
the Display Color button repeatedly to select a
backlight color for the display.
4
3
2
1

15
Measure your heart rate if desired.
Ifthere are sheets
of clear plastic on
the metal contacts
on the handgrip
pulse sensor,
remove the plastic.
To measure your
heart rate, hold the
handgrip pulse sen-
sor with your palms
resting against the metal contacts. Avoid moving
your hands or gripping the contacts too
tightly.
When your pulse is
detected, a heart-
shaped symbol will
flash in the left side
of the display each
time your heart
beats, one or two dashes will appear, and then
your heart rate will be shown. For the most accu-
rate heart rate reading, hold the contacts for at
least 15 seconds. Note: If you continue to hold the
handgrip pulse sensor, the display will show your
heart rate for up to 30 seconds.
If your heart rate is not shown, make sure that
your hands are positioned as described. Be care-
ful not to move your hands excessively or to
squeeze the metal contacts too tightly.For opti-
mal performance, clean the metal contacts using
asoft cloth; never use alcohol, abrasives, or
chemicals to clean the contacts.
Turn on the fan if desired.
Toturn on the fan at high speed, press the Fan
button. To turn on the fan at low speed, press the
button a second time. To turn off the fan, press
the button a third time. Note: If the pedals do not
move for a few minutes, the fan will automatically
turn off to conserve the batteries.
Pivot the thumb tab
on the right side of
the fan to adjust the
fan angle.
When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for several seconds, a
tone will sound and the console will pause.
If the pedals do not move for about five minutes
and the buttons are not pressed, the console will
turn offand the display will be reset.
7
65
Thumb
Tab
Metal Contacts

16
HOW TO USE A CROSS TRAINING PROGRAM
Press the Resistance decrease button or
begin pedaling to turn on the console.
A moment after you turn on the console, the dis-
play will light.
Select one of the five cross training programs.
To select a cross training program, press the
Programs button repeatedly until the name of the
desired cross training program appears in the dis-
play. When a cross training program is selected,
the program time will appear in the display and a
profile of the resistance settings for the program
will scroll across the matrix in the display.
Begin pedaling to start the program.
Each program is divided into 25, 30, or 45 one-
minute segments. One resistance setting and one
target rpm (revolutions per minute) setting are
programmed for most segments. (Note: The same
resistance and/or target rpm setting may be pro-
grammed for two or more consecutive segments.)
During other segments, the console will prompt you
to perform strength exercises.
The resistance setting
for the first segment
will be shown in the
flashing Current
Segment column of
the matrix. The resis-
tance settings for the next several segments will
be shown in the columns to the right. The target
rpm setting will appear in the top of the display.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and
aseries of tones will sound. If the resistance
and/or target rpm is about to change, the resis-
tance setting and/or the target rpm setting will
appear in the display to alert you.
When the first segment is completed,
all resis-
tance settings will move one column to the left .
The resistance setting for the second segment
will then be shown in the flashing Current
Segment column and the resistance of the pedals
will automatically adjust to the setting for the sec-
ond segment. Note: If all the indicators in the
Current Segment column are lit, the resistance
settings may move downward so that only the
highest indicators appear in the matrix.
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the display, increase your
pace. When the words PEDAL SLOWER appear
in the display, decrease your pace. When the
words PEDALING IN RANGE appear, maintain
your current pace.
Important: The target rpm settings are intend-
ed only to provide motivation. Your actual
pace may be slower than the target rpm set-
tings. Make sure to exercise at a pace that is
comfortable for you.
If the resistance setting for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance decrease or
increase buttons. Every few times you press a
Resistance button, an additional indicator will
appear or disappear in the Current Segment col-
umn; if any of the columns to the right of the
Current Segment column have the same number
of lit indicators as the Current Segment column,
an additional indicator may appear or disappear
in those columns as well. Important: When the
current segment of the program ends, the ellip-
tical exerciser will automatically adjust to the
resistance setting for the next segment.
To stop the program at any time, stop pedaling.
The time will begin to flash in the display. To
restart the program, simply resume pedaling.
3
2
1
Current Segment

17
Perform the first strength exercise when
prompted.
When the first strength exercise segment begins,
the name of the first strength exercise will appear
inthe display for a few seconds. The time will
pause and flash in the display. Next, the display
will show the recommended number of repetitions
for the first strength exercise.
Step off the ellipti-
cal exerciser and
prepare to begin
the first strength
exercise. Every few
seconds, the con-
sole will sound a
tone; when a tone sounds, perform one repetition
of the exercise. Exercise with a slow, steady
motion; do not perform more than one repetition
each time a tone sounds. The display will count
down the repetitions as you perform them.
Note: Refer to a weight training manual or exer-
cise guide if you are unfamiliar with the correct
form for each strength exercise. When performing
lunges, alternate legs with each repetition. When
performing dumbbell rows, perform half the repe-
titions with your right arm and half the repetitions
with your left arm. The strength exercises require
the use of dumbbells and an inflatable exercise
ball (not included). To purchase dumbbells or
an exercise ball, call toll-free 1-888-533-1333.
Continue the cross training program.
When you have performed the recommended
number of repetitions, the words START PEDAL-
ING will appear in the display. To continue the
cross training program, step onto the elliptical
exerciser and start pedaling. the pedals will auto-
matically adjust to the resistance setting for the
next segment.
The program will continue in this way until the last
segment ends. Then, the words PROGRAM
DONE will appear in the display.
Follow your progress with the display.
See step 4 on page 14.
Measure your heart rate if desired.
See step 5 on page 15.
Turn on the fan if desired.
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
See step 7 on page 15.
9
8
7
6
54

18
HOW TO USE A CALORIE GOAL PROGRAM
Press the Resistance decrease button or
begin pedaling to turn on the console.
A moment after you turn on the console, the dis-
play will light.
Select one of the calorie goal programs.
Press the Programs button repeatedly until the
name of the desired calorie goal program
appears in the display. When a calorie goal pro-
gram is selected, the program time will appear in
the display and a profile of the resistance settings
for the program will scroll across the matrix in the
display.
Begin pedaling to start the program.
Each program is divided into 25, 30, or 45 one-
minute segments. One resistance setting and one
target rpm (revolutions per minute) setting are
programmed for each segment. Note: The same
resistance setting and/or target rpm setting may be
programmed for two or more consecutive seg-
ments. The display for a calorie goal program work
in the same way as the display for the cross train-
ing programs (see step 3 on page 16).
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the display, increase your
pace. When the words PEDAL SLOWER appear
in the display, decrease your pace. When the
words PEDALING IN RANGE appear, maintain
your current pace.
Important: The target rpm settings are intend-
ed only to provide motivation. Your actual
pace may be slower than the target rpm set-
tings. Make sure to exercise at a pace that is
comfortable for you. Note: If you manually over-
ride the resistance settings of a calorie goal pro-
gram, you may not reach your calorie goal.
To stop the program at any time, stop pedaling.
The time will begin to flash in the display. To
restart the program, simply resume pedaling.
When the last segment of the program ends, the
words PROGRAM DONE will appear in the dis-
play.
Follow your progress with the display.
See step 4 on page 14.
Measure your heart rate if desired.
See step 5 on page 15.
Turn on the fan if desired.
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
See step 7 on page 15.
7
6
5
4
3
2
1

19
HOW TO USE THE HIGH PERFORMANCE PROGRAM
Press the Resistance decrease button or
begin pedaling to turn on the console.
A moment after you turn on the console, the dis-
play will light.
Select the high performance program.
Press the Programs button repeatedly until the
words HIGH PERFORMANCE appear in the dis-
play. The program time will appear in the display
and a profile of the resistance settings for the pro-
gram will scroll across the matrix in the display.
Begin pedaling to start the program.
The program is divided into 45 one-minute seg-
ments. One resistance setting and one target rpm
setting are programmed for each segment. Note:
The same resistance setting and/or target rpm set-
ting may be programmed for two or more consecu-
tive segments. The displays for the high perfor-
mance program work in the same way as the dis-
plays for the cross training programs (see step 3
on page 16).
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the display,increase your
pace. When the words PEDAL SLOWER appear
in the display, decrease your pace. When the
words PEDALING IN RANGE appear, maintain
your current pace.
Important: The target rpm settings are intend-
ed only to provide motivation. Your actual
pace may be slower than the target rpm set-
tings. Make sure to exercise at a pace that is
comfortable for you.
To stop the program at any time, stop pedaling.
The time will begin to flash in the display. To
restart the program, simply resume pedaling.
When the last segment of the program ends, the
words PROGRAM DONE will appear in the dis-
play.
Follow your progress with the display.
See step 4 on page 14.
Measure your heart rate if desired.
See step 5 on page 15.
Turn on the fan if desired.
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
See step 7 on page 15.
7
6
5
4
3
2
1

20
HOW TO USE THE HEART RATE CONTROL PROGRAM
Press the Resistance decrease button or
begin pedaling to turn on the console.
A moment after you turn on the console, the dis-
play will light.
Select the heart rate control program.
Press the Programs button repeatedly until the
words HEART RATE CONTROL appear in the
display.
Enter a target heart rate.
The target heart rate
setting for the program
will flash in the dis-
play. Use the
Resistance increase
and decrease buttons
to change the target heart rate setting.
Hold the handgrip pulse sensor.
It is not necessary to
hold the handgrip
pulse sensor continu-
ously; however, you
should hold the hand-
grip pulse sensor fre-
quently for the program to operate properly. Each
time you hold the handgrip pulse sensor, keep
your hands on the metal contacts for at least
30 seconds. When you are not holding the hand-
grip pulse sensor, the letters PLS will appear in
the display instead of your heart rate.
Begin pedaling to start the program.
During the program, the console will regularly
compare your heart rate to the target heart rate. If
your heart rate is too far below or above the target
heart rate, the resistance of the pedals will auto-
matically increase or decrease to bring your heart
rate closer to the target heart rate.
You will also be prompted to pedal at a steady
pace so you can maintain your target heart rate.
When the words PEDAL FASTER appear in the
display, increase your pace. When the words
PEDAL SLOWER appear in the display, decrease
your pace. When the words PEDALING IN
RANGE appear, maintain your current pace.
Important: Make sure to exercise at a pace
that is comfortable for you. Note: If you manu-
ally override the resistance settings, you may not
maintain your target heart rate.
Tostop the program at any time, stop pedaling.
The time will begin to flash in the display. To
restart the program, simply resume pedaling.
Follow your progress with the display.
See step 4 on page 14.
Measure your heart rate if desired.
See step 5 on page 15.
Turn on the fan if desired.
See step 6 on page 15.
When you are finished exercising, the console
will turn off automatically.
See step 7 on page 15.
9
8
7
6
5
4
3
2
1