Pro-gard Products LLC. 3B300WDT User manual

STRONG
|
RELIABLE
|
SECURE
INSTALLATION GUIDE
3B300WDT
CARGO BARRIER
‘09 CHEVROLET TAHOE
pro-gard.com
800.480.6680

THESE COMPONENTS ARE REQUIRED
TO INSTALL THE PRO-GARD BARRIER SYSTEM
pro-gard.com
800.480.6680 2
3B300WDT BARRIER
III. Read all instructions carefully before starting the
assembly process.
NOTE: Locate all Wiring, Fuel Lines, Brake Lines,
and/or Cooling Lines before drilling holes or
installing Fasterners.
IV. Barrier Installation
A. Install the upper mounting brackets (3P5731D
Driver and 3P5731P Passenger) to the barrier using
I. Refer to the diagram on the last page of these instructions to verify all parts were received.
II. The following tools will be required to complete the installation.
A. 1/4” drive ratchet with 7/16” socket
B. Phillps Screwdriver
C. Drill with 3/8” socket
4B57T09 HARDWARE/WING KIT
DRIVER’S SIDE SHOWN
FIG. 1
Barrier Assembly
3P5731D 3X139
3X36
3X16
SPACER
the phillips head bolts (3X36) and whiz nuts (3X16) through the holes in the top of the
Barrier. Hand tighten only. See Fig. 1
B. Remove the rear OEM coat hook assemblies from the headliner.
 C.PlacetheCargoBarrierAssemblyonthecargooorbehindthesecondrowseats.Note: 
 Thebottomofthebarriershouldbealignedalongtheedgeoftheoorbehindthe  
second row seats. With the seats folded down begin to stand the Barrier up.
While raising the Barrier swing the upper mounting brackets around torward the rear
of vehicle. Align the upper mounting brackets with the coat hook mounting holes and
secure loosely using the supplied M6 bolts and spacers. See Fig. 1
D. Attach the Polycarbonate top panel (3B57C) to the Barrier using the exsiting bolts from
the top of the barrier window frame. Hand tighten fasteners only. See Fig. 3
3X97

pro-gard.com
800.480.66803
E. Attach the Polycarbonate Wings (3B57A Driver
and 3B57B Passenger) between the Barrier
and the interior trim using the Phillips head
bolts (3X05A) and whiz nuts (3X16). Hand
tighten fasteners only. See Fig. 3
F. Center the Barrier Assembly in the the vehicle.
G. With the top now supported, raise the second
row seats in the vehicle, shifting the bottom
of the barrier front to back to clear the back of
second row seats as desired. Adjust the
 Polycarbonatewingsfordesiredt 
against the interior trim and headliner.
CAUTION: Before using Self-Tapping
Fasterners, verify that there are
NO Wiring Harnesses, Fuel, Brake,
and/or Cooling Lines in or near the
Fasterners path.
 H.SecuretheBarrierattheoorusingthe 
supplied 3X110 self-drilling screws
I. Tighten all fasterners
3B57C
Barrier Assembly
3B57A
3B57B
FIG. 3
FIG. 2
DRIVER’S SIDE SHOWN
Barrier Assembly
3X110
3X110

pro-gard.com
800.480.6680 4
FIG. 4
3P5731D
3X36
Spacer
3X36
3X05A
3X16 nuts
at rear
3P5731P
3X110 into
cargooor
3B57A
3B57B
3B57C
Spacer
3X05A
3X05A
3B300WDT
Barrier Assembly