Pro-gard Products LLC. RC1095 User manual

pro-gard.com
800.480.6680
INSTALLATION GUIDE
Released 1.16.2024
SEAT BELT KIT
PRO-STRAINT CHAIR
RC1095

2
pro-gard.com
800.480.6680
I. The following tools will be required to complete the installation
II. Read all instructions and refer to Figure 1 to ensure all parts were received.
III. Leg Restraint Buckle Replacement (Fig. 2)
A. Remove 3/8-16 button head screw, 3/8-16 nylon lock nut, and washers.
B. Remove original Leg Restraint Buckle and discard.
C. Install new Leg Restraint Buckle (RC1222) using hardware removed in
step A.
THESE COMPONENTS ARE
INCLUDED IN RC1095 SEAT BELT KIT
A. 9/16” socket
B. 9/16” wrench
C. T30 Torx bit
D. 7/32 Allen wrench or bit
E. Ratchet
RC1019
RC1221 (Blue)
RC1218 (Red)
RC1223
RC1222
RC1023
RC1220 (Red)
RC1219 (Blue)
Figure 1
Figure 2

3
pro-gard.com
800.480.6680
IV. Shoulder Restraint Buckle and Waist Restraint Replacement
A. Remove 3/8-16 nylon lock nut and washer from Leg Restraint Retractor. (Fig. 3)
B. Remove Leg Restraint Retractor from stud on leg retractor bracket, then feed leg restraint belt and handle
through the opening on side of chair. Discard Leg Restraint Retractor. (Fig. 3, 4) Replacement will be
covered in a later section.
C. Remove 3/8-16 nylon lock nut, washer, and buckle ends from stud in each side of chair. (Fig. 3) Pull the
Shoulder Restraint Buckle and Waist Restraint through the top side of the chair and discard. Do this for
both sides.
D. Remove plastic caps from Shoulder Restraint Buckles (RC1221/RC1220) (Fig. 5).
E. Feed new Shoulder Restraint Buckle (RC1221/RC1220) and Waist Restraint (RC1019/RC1023) through slot
in each side of the seat base (Fig. 6). Install buckle ends onto threaded studs using hardware removed in
step C. *Note: Red and Blue buckles should be opposite of Red and Blue Shoulder Retractors. Make sure
unlock hole in buckle is facing outwards.
V. Leg Restraint Retractor Installation
A. From inside chair, feed leg restraint belt and handle (RC1223) through the opening on side of chair (Fig. 7).
B. Install Leg Restraint Retractor (RC1223) onto leg retractor bracket using 3/8-16 hardware removed in step
IV A (Fig. 8).
D E
A
B
B
C
Figure 3 Figure 4
Figure 5 Figure 6

4
pro-gard.com
800.480.6680
C. Pull leg restraint belt and feed through cinch strap, insert into Leg Restraint Buckle (RC1222) and tighten
cinch strap (Fig. 9).
VI. Shoulder Retractor Replacement
A. Locate the 1/4-20 button head screw on top of seat near each shoulder retractor handle. Loosen screw so
that seat base can be moved away from chair frame (Fig. 10).
B. Uninstall each Shoulder Retractor by removing the 3/8-16 nylon lock nut and washer from threaded stud in
the upper cross member of chair. Seat base removed for clarity in image below (Fig. 11).
C. Carefully push seat base away from chair frame to allow the shoulder retract handle to be pulled through
the slot (Fig. 12). Do this for both sides and discard original Shoulder Retractors.
A
B
Figure 7 Figure 8
Figure 9
A
B
C
Figure 10
Figure 11 Figure 12

5
pro-gard.com
800.480.6680
D. Carefully push seat base away from chair frame to slide new Shoulder Retractor (RC1218/RC1219) handle
through the top slot. Do this for both sides.
E. Using hardware removed in step B, Install Shoulder Retractor onto threaded stud in the upper cross
member of chair. Do this for both sides.
F. To secure the seat base, tighten 1/4-20 button head screws from step A.
Installation complete
If you have any problems with this installation or have any questions please call (800-480-6680)
and ask for technical assistance.
Figure 13