Pro-gard Products LLC. GVRM5715D-H User manual

STRONG
|
RELIABLE
|
SECURE
INSTALLATION GUIDE
GVRM5715D-H
CARGO MOUNTING STAND
2016 - 2020 CHEVYTAHOE
pro-gard.com
800.480.6680

2
pro-gard.com
800.480.6680
I. Refer to the diagram above to verify all parts were received.
II. The following tools will be required to complete the installation:
A. 7/16” Socket & Ratchet D. 5/16” and 3/8” Drill bit
B. 5/32” Allen Wrench E. 18mm Socket
C. 9/32” Allen Wrench F. T-45 Torx Bit
III.Read all instructions carefully before starting the assembly process.
Locate all wiring, fuel lines, brake lines, and /or cooling lines before drilling holes or installing
any fasteners.
IV. Mounting Base Installation
A. Mount the (3G5717-01) mounting base to the oor of the cargo area utilizing two OEM hole
locations. Carefully lift the oor material up to nd the Two OEM Hole locations. (See Fig. 1)
THESE COMPONENTS ARE REQUIRED TO INSTALL
THE PRO-GARD 4GBK57-02 SELF SUPPORTING STAND AND TRI-LOCK GUN RACK
NOTE:
3G5717-01 MOUNT BASE
GVPMXXXX
Tri-Lock Gun Rack
3G5717-02 MOUNTING
BRACKET
B. Use the bolts to mount the base to the oor in
the OEM hole locations.
C. Attach the Gun rack to the mounting base using
the (3X184) bolts.
V. Mounting Bracket Installation
A. Mount the (3G5717-02) mounting bracket to the
OEM hole location that the coat hangar hook
utilizes. (See Fig. 1)
B. Attach the mounting bracket to the gun rack
using the (3X184) bolt, (3X12) washer and
(3X234) weld nut.
VI. Base Installation Complete
(Continue with gun rack installation on the next page)

VII. Installing the Tri-Lock gun rack (Requires Pro-gard self-supporting mounting base)
A. Place the intended guns into the gun rack and make adjustments to t. This will allow more access than
when the rack is in the vehicle, but the rack can be adjusted after installed inside the vehicle as well.
B. The brackets mounting the gun lock are designed to be loosened and adjusted in many directions to
accomodate most guns. Fit each gun by loosening the bolts on the gun lock bracketry so the mounting
bracket moves freely. Place your gun into the lock and in the desired position. Take a allen wrench to
tighten locks in place. (See Fig. 3)
C. Shot Gun Mounting - The shot gun can be mounted in two ways, by barrel mount or by installation of
the shot gun mount insert. To install the shot gun insert, remove the standard insert by opening the
lock and unscrewing the two insert bolts with an allen wrench. Remove the retaining ring from the bolt’s
back side. Replace with shot gun insert (3G724) and reinstall insert bolts and retaining rings on the
back side of the insert. Use the two fastener bolt’s adjustment to t the shot gun used in the lock. (See
Fig. 4)
Locks move up and down
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Tilts clockwise
or counter clockwise
Left and right
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Completed Gun Fitment
Gun locks should open
and close easily and guns
should pull in and out of
the rack with no issues
when properly installed
Fig. 3
The shot gun
shown in the
lower position
with insert
pro-gard.com
800.480.6680 3
Fig. 4
Step 1
Remove barrel bracket
Step 2
Remove standard insert
Step 3
Replace with shot gun insert
Barrel
mounting bracket Standard insert Shot gun
insert
Retaining ring

VIII. Self-Supporting Installation
A. For self-supporting installations, remove the
four bolts that secure the butt plates to the
base of the gun rack. Then rest the gun rack
to the self supporting stand, loosely attach the
gun rack and adjust it and the butt plates as
necessary from front to back. (See Fig. 5)
IX. Lock Box
A. Open the lock box and loosen the bolts with a
7/16” socket and extension wrench to adjust the
box up or down as needed. (Swivel attachment
is required) Install supplied black felt over bolts
when box position has been xed. (See Fig. 6)
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Lock box
adjustment
bolts
Fig. 6
pro-gard.com
800.480.6680
4
Fig. 5
For Optimal Conditions secure the back
of the gun rack tigth against the seat.
NOTE:

X. Gun lock switch and timer installation.
A. We suggest mounting the momentary release button in a concealed location that can be easily reached
by the ofcer, but would be hidden in case an unathorized entry occurs.
B. Connect the gun lock wiring as shown in the diagram below.
Pro-gard requires the use of a 10 AMP fuse between the power source and gun lock circuit or the
warranty will be voided!
XI. Lock Head Operating Instructions
A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then
pull the weapon towards the lid of the gun lock to release it from the lock.
One handed operation is possible utilizing the optional 8 second timer. The timer will unlock the
lock for 8 seconds following activation of the momentary switch. If the gun is not pulled out of
the lock within 8 seconds after activation of the momentary switch, the lock will automatically
re-lock.
If lid of the lock does not release, press in on the lid to release tension and reactivate the release
button (unless timer is still active).
Installation Complete!
Call Pro-gard technical support if assistance is needed. 1-800-480-6680
NOTE:
Fig. 7
NOTE:
TIP:
pro-gard.com
800.480.6680 5

6
pro-gard.com
800.480.6680
Self-Supporting Mounting Base
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
CARGO MOUNTING BASE3G5717-01
11
TRI-LOCK PARTITION GUN RACK4GVPM201
1
2
1/4-20x0.75, SBHCS, BLACK OXIDE3X18483
1/4 FLAT WASHER, BLACK3X12
14
1-4-20 Weld Nut3X234
15
TAHOE CARGO UPPER MOUNT3G5717-0216
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Products, LLC
9650 East 148th Street
Noblesville, IN 46060
[phone]
PART DESCRIPTION:
DRAWN BY:
SCALE:
CHECKED BY:
DATE:
APPROVED:
UNLESS OTHERWISE SPECIFIED :
The information contained herein is
proprietary and the property of Pro-gard
Products and may not be reproduced,
disclosed or used for any other purpose other
than a quotation to or an order from
Pro-Gard Products without the specific
written authorization of Pro-gard Products. Computer Path:
SIZE:
A
ENGR 1:
ENGR 3:
ENGR 2:
FINAL:
PRODUCTION:
Third
Angle
Projection
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMALS:  .005
DIMENSIONS ARE IN INCHESTOL ON ANGLES 1°
TOL ON 2 PLACE DECIMAL  .015
NOTE:
MATERIAL:
FINISH:
STAMP:
ASSEMBLY NO: DRAWING NO:
SHEET:
REV:
APPL:
Pro-gard
DUSTIN
2/23/2017
Gunrack Base Kit, Tahoe Cargo
4GBK57-02
1
FREE OF SHARP EDGES
V:\New Product Development\Gun Racks\Tahoe cargo mount\4GBK57-02.iam
2
6
3
4
1
3
5
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
CARGO MOUNTING BASE3G5717-01
11
TRI-LOCK PARTITION GUN RACK4GVPM201
1
2
1/4-20x0.75, SBHCS, BLACK OXIDE3X18483
1/4 FLAT WASHER, BLACK3X12
14
1-4-20 Weld Nut3X234
15
TAHOE CARGO UPPER MOUNT3G5717-0216
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Products, LLC
9650 East 148th Street
Noblesville, IN 46060
[phone]
PART DESCRIPTION:
DRAWN BY:
SCALE:
CHECKED BY:
DATE:
APPROVED:
UNLESS OTHERWISE SPECIFIED :
The information contained herein is
proprietary and the property of Pro-gard
Products and may not be reproduced,
disclosed or used for any other purpose other
than a quotation to or an order from
Pro-Gard Products without the specific
written authorization of Pro-gard Products. Computer Path:
SIZE:
A
ENGR 1:
ENGR 3:
ENGR 2:
FINAL:
PRODUCTION:
Third
Angle
Projection
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMALS:  .005
DIMENSIONS ARE IN INCHESTOL ON ANGLES 1°
TOL ON 2 PLACE DECIMAL  .015
NOTE:
MATERIAL:
FINISH:
STAMP:
ASSEMBLY NO: DRAWING NO:
SHEET:
REV:
APPL:
Pro-gard
DUSTIN
2/23/2017
Gunrack Base Kit, Tahoe Cargo
4GBK57-02
1
FREE OF SHARP EDGES
V:\New Product Development\Gun Racks\Tahoe cargo mount\4GBK57-02.iam
2
6
3
4
1
3
5

Tri-Lock Gun Rack
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
RACK BASE WELDMENT3GVM201-01
11
1.5" X 1.5" X 38" LG. ALUM EXTRUSION3GVM001-04
1
2
BUTT PLATE - BLACK NYLONG4962-00223
RUBBER BUTT PLATE PAD
G4963-0022
4
LOCK MOUNTING BRACKET - PASSENGER3GVM201-02
15
LOCK MOUNTING BRACKET - DRIVER3GVM201-03
1
6
R GUN LOCKG4904-NPG2
7
R LOCK BARREL MOUNT BRACKET3G13528
UPPER PARTITION MOUNTING BRACKET3G7030
1
9
LOWER PARTITION MOUNT BRACKET (NOT SHOWN)3G7031
1
10
LOCK INSERT FOR SHOT GUN3G724
111
GUN SAFE4GLB02
1
12
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
5/16-18 X 3/4 BSHCS, BK3X149
4
13
1/4 FLAT WASHER, BLACK3X1213
14
1/4-20 X 0.5 BSHCS3X258
715
1/4-20 SLOT NUT (NOT SHOWN)
3X259
18
16
1/4 FLAT WASHER, BLACK
3X33617
1/4-20 x 1" HHMS, Zn
3X122618
1/4-20x0.75, SBHCS, BLACK OXIDE
3X184719
1/4-20 X 3/4 CARRIAGE BOLT
3X61120
1/4-20 WHIZ NUT
3X16Z121
EXTRUSION END CAP01501-PLAIN122
1/4-20 WHIZ NUT (NOT SHOWN)
3X16423
5/16-18 X 0.313 LG. BSHCS, BK
3X235124
6-32 SLOT NUT3X233125
NEODYMIUN MAGENTNB020-TH126
6-32 X 5/8 FHSCS
3X232127
1/4-20 X 0.5 HEX CAP SCREW
3X231228
0.125 RIVET (NOT SHOWN)
3X229129
BLACK FELT 17 3/4" X 31" QTY CONSUMED (NOT SHOWNT)
3G5078R130
LOCK BOX FELT (NOT SHOWN)
3G5078R-01131
1
1
2
2
3
3
4
4
A A
B B
C C
D D
24
22
78
15 14
513
2
9
28
613
8
14
7
15
20
14
10
21
14
26
27
14
15
12
19
18
1
3
4
25
17
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
RACK BASE WELDMENT3GVM201-01
11
1.5" X 1.5" X 38" LG. ALUM EXTRUSION3GVM001-04
1
2
BUTT PLATE - BLACK NYLON**G4962-002*23
RUBBER BUTT PLATE PAD
**G4963-002*2
4
LOCK MOUNTING BRACKET - PASSENGER3GVM201-02*1
5
LOCK MOUNTING BRACKET - DRIVER3GVM201-03*16
R GUN LOCK**G4904-NPG*2
7
R LOCK BARREL MOUNT BRACKET**3G135*28
UPPER PARTITION MOUNTING BRACKET3G7030
1
9
LOWER PARTITION MOUNT BRACKET (NOT SHOWN)3G7031
1
10
LOCK INSERT FOR SHOT GUN3G724*1
11
GUN SAFE4GLB02*112
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
5/16-18 X 3/4 BSHCS, BK3X149
4
13
1/4 FLAT WASHER, BLACK3X1213
14
1/4-20 X 0.5 BSHCS3X258
715
1/4-20 SLOT NUT (NOT SHOWN)
3X259
18
16
1/4 FLAT WASHER, BLACK
3X33617
1/4-20 x 1" HHMS, Zn
3X122618
1/4-20x0.75, SBHCS, BLACK OXIDE
3X184719
1/4-20 X 3/4 CARRIAGE BOLT
3X61120
1/4-20 WHIZ NUT
3X16Z121
EXTRUSION END CAP01501-PLAIN122
1/4-20 WHIZ NUT (NOT SHOWN)
3X16
*4
23
5/16-18 X 0.313 LG. BSHCS, BK
3X235124
6-32 SLOT NUT3X233125
NEODYMIUN MAGENTNB020-TH126
6-32 X 5/8 FHSCS
3X232127
1/4-20 X 0.5 HEX CAP SCREW
3X231228
0.125 RIVET (NOT SHOWN)
3X229129
BLACK FELT 17 3/4" X 31" QTY CONSUMED (NOT SHOWNT)
3G5078R130
LOCK BOX FELT (NOT SHOWN)
3G5078R-01131
MOMENTARY SWITCH3G5100132
TIMER DELAY MODULEG1002133
1
1
2
2
3
3
4
4
A A
B B
C C
D D
24
22
78
15 14
513
2
9
28
613
8
14
7
15
20
14
10
21
14
26
27
19
18
1
3
4
25
17
12
* - QTY MAY VARY DEPENDING ON CONFIGURATION
** - ITEM MAY VARY DEPENDING ON CONFIGURATION
pro-gard.com
800.480.6680
7