Pro-gard Products LLC. GVM5419X-X User manual

pro-gard.com
800.480.6680
INSTALLATION GUIDE
GVM5419X-X
SELF SUPPORTING BASE
FOR 2019-1/2 - CURRENT
CHEVROLET SILVERADO

2
pro-gard.com
800.480.6680
I. Refer to the diagram above to verify all parts were received.
II. The following tools will be required to complete the installation:
A. 7/16” Socket & Ratchet D. 5/16” and 3/8” Drill bit
B. 5/32” Allen Wrench E. 18mm Socket
C. 9/32” Allen Wrench F. T-45 Torx Bit
III. Read all instructions carefully before starting the assembly process.
Locate all wiring, fuel lines, brake lines, and /or cooling lines before drilling holes or installing
any fasteners.
IV. Mounting Base Installation
A. Position both the driver and passenger seats as far forward and up as
possible.
B. Use a T-45 torx bit to loosen the inner seat bolts located on the passenger
and drivers side by approximately 1/2”. Refer to Figure. 1
C. Tilt the the seats forward and to the outside, lifting the seat track from the
oor slightly.
D. Place 3G5419-03 under the seat tracks and slide slots around and through
the seat bolts loosened in the previous step. Loosly secure the OEM bolt
back into location. Align this bracket with (3G5419-02). Secure using the
provided (3X03) bolt and (3X12) washer.
E. Ensure all bolts are tightened rmly.
F. Using the base as a template, mark your drill location in the holes as shown in Figure 2.
THESE COMPONENTS ARE REQUIRED TO INSTALL
THE PRO-GARD SELF SUPPORTING STAND AND TRI-LOCK GUN RACK
NOTE:
Figure 1.
4G5419 MOUNT BASE
GVPMXXXX
Tri-Lock Gun Rack

3
Figure 2.
Locate all wiring, fuel lines, brake lines, and /or cooling lines before drilling holes or installing
any fasteners.
G. Drill the holes using a 3/8” drill bit making sure to remove any possible burrs.
H. Install the bolt (3x119) from the top as shown in Figure 2, and then the rubber washer (3x310),
fender washer (3x311) from the bottom, and the lock nut (3x120). A second installer may be
needed to hold the bolt inside the vehicle, while the other installer tighens the nut from below the
vehicle.
V. Base Installation Complete
(Continue with gun rack installation on the next page)
NOTE:
3X119
3X120
3X310
3X311

pro-gard.com
800.480.6680
4
VI.Installing the Tri-Lock gun rack (Requires Pro-gard self-supporting mounting base)
A. Place the intended guns into the gun rack and make adjustments to t. This will allow more access than
when the rack is in the vehicle, but the rack can be adjusted after installed inside the vehicle as well.
B. The brackets mounting the gun lock are designed to be loosened and adjusted in many directions to
accomodate most guns. Fit each gun by loosening the bolts on the gun lock bracketry so the mounting
bracket moves freely. Place your gun into the lock and in the desired position. Take a allen wrench to
tighten locks in place. (See Fig. 3)
C. Shot Gun Mounting - The shot gun can be mounted in two ways, by barrel mount or by installation of
the shot gun mount insert. To install the shot gun insert, remove the standard insert by opening the
lock and unscrewing the two insert bolts with an allen wrench. Remove the retaining ring from the bolt’s
back side. Replace with shot gun insert (3G724) and reinstall insert bolts and retaining rings on the
back side of the insert. Use the two fastener bolt’s adjustment to t the shot gun used in the lock. (See
Fig. 4)
1
1
2
2
3
3
4
4
A A
B B
C C
D D
Tilts clockwise
or counter clockwise
Left and right
Completed Gun Fitment
Gun locks should open
and close easily and guns
should pull in and out of
the rack with no issues
when properly installed
Fig. 3
The shot gun
shown in the
lower position
with insert
Fig. 4
Step 1
Remove barrel bracket
Step 2
Remove standard insert
Step 3
Replace with shot gun insert
Barrel
mounting bracket Standard insert Shot gun
insert
Retaining ring
Locks move up and down

5
VII. Self-Supporting Installation
A. For self-supporting installations, remove the
four bolts that secure the butt plates to the
base of the gun rack. Then rest the gun rack
to the self supporting stand, loosely attach the
gun rack and adjust it and the butt plates as
necessary from front to back. (See Fig. 5)
VIII. Lock Box
A. Open the lock box and loosen the bolts with a
7/16” socket and extension wrench to adjust the
box up or down as needed. (Swivel attachment
is required) Install supplied black felt over bolts
when box position has been xed. (See Fig. 6)
SECTION A-A
SCALE .15
AA
Lock box
adjustment
bolts
Fig. 6
Fig. 5
For Optimal Conditions secure the back
of the gun rack tigth against the seat.
NOTE:
Adjustable hole
locations to
provide the best
mounting
preference.

pro-gard.com
800.480.6680
6
IX.Gun lock switch and timer installation.
A. We suggest mounting the momentary release button in a concealed location that can be easily reached
by the o󰀩cer, but would be hidden in case an unathorized entry occurs.
B. Connect the gun lock wiring as shown in the diagram below.
Pro-gard requires the use of a 10 AMP fuse between the power source and gun lock circuit or the
warranty will be voided!
X. Lock Head Operating Instructions
A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then
pull the weapon towards the lid of the gun lock to release it from the lock.
One handed operation is possible utilizing the optional 8 second timer. The timer will unlock the
lock for 8 seconds following activation of the momentary switch. If the gun is not pulled out of
the lock within 8 seconds after activation of the momentary switch, the lock will automatically
re-lock.
If lid of the lock does not release, press in on the lid to release tension and reactivate the release
button (unless timer is still active).
Installation complete!
If you have any problems with this installation than call the toll free number (800-480-6680)
and ask for technical assistance.
NOTE:
Fig. 7
NOTE:
TIP:

7pro-gard.com
800.480.6680
Self-Supporting Mounting Base

pro-gard.com
800.480.6680
8
Tri-Lock Gun Rack
21
2
28 23 14
11
16
1
12
16
14
29
23
30
22
15
10
4
4
25
24
26
14
23
3
3
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
1.5" X 1.5" LOT T SLOTTED 38"1515-LITE-BLACK 80/20 INC
11
END CAP W/O FASTNER PLAIN
203001-PLAIN
1
2
R LOCK BARREL MOUNT BRACKET3G135
*2
3
BUTT PLATE BLACK NYLON3G4962-0022
4
RUBBER BUTT PLATE PAD3G4963-00225
BLACK FELT (NOT SHOWN)
3G5078R
1
6
LOCK BOX FELT (NOT SHOWN)
3G5078R-0117
MOMENTARY SWITCH3G5100
1
8
LOCK INSERT FOR SHOT GUN3G724
*1
9
RACK BASE WELDMENT3GVM201-01
1
10
LOCK MOUNTING BRACKET - PASSENGER3GVM201-02
*1
11
LOCK MOUNTING BRACKET - DRIVER3GVM201-03*112
TRIM, RUBBER GUNRACK3R50109
4
13
1/4 FLAT WASHER, BLACK3X12
1014
1/4-20 x 1" HHMS, Zn
3X1226
15
5/16-18 X 3/4 BSHCS, BK
3X149416
1/4-20 WHIZ NUT (NOT SHOWN)
3X16
*4
17
1/4-20x0.75, SHCS, BLACK OXIDE
3X184718
06-32 WELD NUT N-D 11143X233
1
19
1/4-20 SLOT NUT (NOT SHOWN)
3X2341620
5/16-18 X 5/16 LG.BSHCS, BK
3X235
1
21
6-32 X 1-1/2 FLAT HD SOC CAP SCR
3X242122
1/4-20X1/2 BUTT HD SOC SC BLK
3X258
7
23
1/4 FLAT USS WASHER, ZINC
3X33624
SPACER, PLASTIC, 3/4" LONG4G5070P2
1
25
GUN SAFE4GLB02-01
*1
26
TIMER DELAY MODULEG1002
1
27
R GUN LOCKG4904-NPG
1
28
LOCKG4904X129
MAGNET 1/2" X 1/2" X 1/4"
NB020-TH
1
30
* - QTY MAY VARY DEPENDING ON CONFIGURATION
** - ITEM MAY VARY DEPENDING ON CONFIGURATION