PROAIM 14ft. Jib Arm with Jib Stand User manual

14ft. Jib Arm with Jib Stand
(P-14-JS)
I n s t r u c t i o n M a n u a l
All rights reserved
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permied by
the applicable copyright statutes or in wring by the publisher.

PROAIM 14FT JIB ARM WITH STAND 2
IT IS IMPORTANT THAT YOU READ AND UNDERSTAND THIS GUIDE BEFORE ATTEMPTING TO
ASSEMBLE OR USE YOUR NEW PROAIM 14’ JIB ARM.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE ‘ON
LINE' BY CONTACTING YOUR SALES REPRESENTATIVE.
INTRODUCTION
PROAIM welcomes you to the new and modernized era with its huge & sturdy 14 Jib Arm with
Jib Stand, a perfect lming soluon to increase your producon value. The Robust camera crane
produces breathtaking footage through its huge set of features at a small price. Lcd mounng
opon enables beer viewing possibilies for operator.
WHAT’S IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below. The padded shipping /storage container has been especially designed
to protect your purchase while in transit and is a good place to keep your PROAIM 14’ Jib Arm
when not in use.
PACKED IN AN EASY CARRY, PROTECTIVE TOTE BAG.
CONTENTS OF SHIPPING BOX:
 Four 3.5 Secons
 Central Post
 Weight Shank
 Weight Closers
 Jib Stand
 LCD Mounng Arm
 Tool Pouch
 This Manual
1st secon
2nd secon
3rd secon
4th secon
Weight closer Weight shank
Central post
Jib stand
Tool Pouch
LCD mounng arm

PROAIM 14FT JIB ARM WITH STAND 3
Using the following pictures and text as a guide for set up, please follow the instrucons in
order of appearance.
For stability and mounng of your 14’ Jib Arm on the stand take out the stand from the case
and proceed as follows:
 Loosen the lower knob 1 located at the top of the spreader legs
 Slide the legs down the center post to the widest possible posion and ghten the knob 1
to secure.
NOTE: A wider spread ensures more stability.
 Draw the center post up to the desired jib height and lock into place using the provided
locking pin.
ASSEMBLING THE JIB ARM
 Slide the Central Post of the Jib onto the Stand Mount and ghten the knob 2 to secure it.
JIB STAND SET UP
Knob 1
Knob 2

PROAIM 14FT JIB ARM WITH STAND 4
CONNECT THE 3RD JIB SECTION TO THE CENTER POST
 Open the shank from the central post.
Leave the black washers at one side.
 Then insert the end of this secon
inside the Center Post and align the
holes of the secon with the central
post to screw in the shank.
 Similarly, insert the black washers
onto the other side and push the
shank towards the other side in order
to ghten the shank with the dome
nut.
 Using a wrench, ghten the dome
nut from both sides to secure the
two secons.

PROAIM 14FT JIB ARM WITH STAND 5
CONNECTING ARM SECTIONS 3 WITH 2, 2 WITH 1 & 4 WITH 3
 The 3rd secon has connecng bars aached to both the ends. Slide the bars of secon 3
into the slots of secon 2 & ghten both the secons together using the provided allen
Key. Similarly slide in secon 1 into secon 2 and nally secon 4 into secon 3.
 Tighten the allen bolts as before to secure the secons. Your jib arm is now completely
connected
 Tighten the wire puller and its
central pool adapter. Tighten the
bolts to secure them
ADJUSTING THE WIRE TENSIONER
 To add strength and stability to your
Jib and allow for maximum weight
carrying, the fore and a wire ends
once posioned need to have the
slack taken out by use of the wire
adjuster shown above. Once
connected in line with the wire,
simply rotate the mid secon han-
dle to ghten the wire adding the
required amount of strength to the
system.
Screw-In System
Wire Adjustment

PROAIM 14FT JIB ARM WITH STAND 6
ADDING THE COUNTER WEIGHTS
 Securing the counter weights to the Jib
is accomplished by the use of the
stainless steel shank. It has two lock
os, one for each side of the Arm to
prevent the weights from shiing
during use or accidentally falling o the
jib.
 Standard exercise weights (not
supplied) with a 1’ hole are easily
mountable and are used to equal the
weight placed on the camera side of
the Jib.
 Once you discover correct balance,
consider marking the weights for that
parcular camera facilitang an easier
set up the next me.
Weights shown in
The image are for
Demonstraon.
CAMERA MOUNTING PLATE
 To accommodate various manufactur-
ers and dierent sized cameras,
mulple slots are provided for
aachment.
 You will need to ne tune your
counterweights to accommodate
camera, head and other accessories
being used on the Jib Arm.
MOUNTING THE PAN-TILT HEAD
 If you are using the remote capability of a
Pan/Tilt Head, it can be easily mounted to
the jib via the 4 slots located at the
corners of the plate using 4 screws.
 This assembly is usually accomplished
from the underside (boom) of the jib
camera plate.

PROAIM 14FT JIB ARM WITH STAND 7
PIN FEATURE FOR TILTING SHOTS
 Removing the locking pin on the Center
Post allows the operator to frame lng
shots by the use of control handle.
MOUNTING A MONITOR
 Provisions for LCD monitor mounng to
the Jib Arm are built in. The monitor is
not provided.
PROAIM 14FT. JIB ARM WITH JIB STAND
ALL DRESSED UP AND GOOD TO GO
(SHOWN WITH OPTIONAL ACCESSORIES)

PROAIM 14FT JIB ARM WITH STAND 8
WARRANTY
We oer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
crasmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
dues are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequenal damages resulng from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers aer the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. Aer that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without rst geng a response and geng the approval to send back
the item.
In case of any kind of dissasfacon, we urge you to Contact us immediately and we shall do our
best to help you out.
For any other assistance you can reach us via email.