PROAIM CINEMA Series User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Megagrip Car/Vehicle Camera Mount (CM-MGGP)
Ass e mb l y M a n u a l
3 x Sucon Cups
6 x 360° Rod Clamps
3 x Rod
Jointers Hard Case
Camera Plate with Ball Head
2 x Safety Straps
3 x 24” Rods (Ø 16mm) 3 x 12” Rods (Ø 16mm)
4 x Rubber Sleeves
Note: If you have purchased (CM-MGGP-00) kit, you will receive the following:

2
Remove the complimentary dust cover and
place your rst sucon cup on selected
posion from where you want to shoot.
Press down sucon cup and keep pushing
pump to rmly x it on surface. Repeat this
process for all sucon cups.
Aach the Adjustable Rod Clamp with sucon
cup and ghten knob to secure the clamp.
Megagrip Setup
Insert rod of any desired length into rod
clamp and ghten it with the knob. Then by
repeang the previous step, aach rod clamp
to other end of rod and x it by the knob.
To guarantee proper adhesion of sucon cups, check that the surfaces of both, sucon cup and
mounng surface are clean, dry & dust–free.
NOTE: Please mount the device on smooth, even and non-porous surfaces.
3 x Sucon Cups
6 x 360° Rod Clamps
3 x Rod
Jointers Flight Case
Camera Plate with Ball Head
2 x Safety Straps
3 x 24” Rods (Ø 16mm) 3 x 12” Rods (Ø 16mm)
4 x Rubber Sleeves
Note: If you have purchased (CM-MGGP-01) kit, you will receive the following:

3
Use the rubber sleeves to avoid dents and
scratches on car paint. Tighten tension straps
carefully to avoid damages.
The length of Rods can be extended as per
your setup requirements with help of rod
jointer/connector, to achieve dierent
conguraons.
Things To Remember
You can easily adjust/level the angle of each
rod clamp through the provided knob in 360°
Pan & Tilt Rotaon, which gives extra
exibility, and thus you can mount cups to
virtually any part of vehicle.
You can adjust angle of Ball Levelling Camera
Plaorm at any required angle in 360°
rotaon, and can be locked down with knob
when you wish to capture shots in stac
posion.
NOTE: Test all xtures before driving.
Aach ball levelling camera plate with rod
clamp and secure it carefully by ghtening
the knob. Repeat same process for rest of
clamps.
Although the Megagrip’s holding force is
adequate for regular driving shots, safety
belts/tension straps must be used for
addional security. When mounted on cars,
the objects aached to Megagrip (e.g.
camera) have to be secured addionally.

4
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
YOUR PROAIM MEGAGRIP CAR/VEHICLE CAMERA MOUNT
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)