Promax HD Ranger + User manual

HD RANGER/ +
TV & SATELLITE ANALYSER
- 0 MI1914 -

SAFETY NOTES
Read the user’s manual before using the equipment, mainly "SAFETY RULES"
paragraph.
The symbol on the equipment means "SEE USER’S MANUAL". In this manual
may also appear as a Caution or Warning symbol.
WARNING AND CAUTION statements may appear in this manual to avoid injury
hazard or damage to this product or other property.
MULTIMEDIA CONTENT
Throughout this manual are boxes with the symbol . It identifies a direct
access to an explanatory video related to the function where it is. User has to click on
this icon to watch the video.
All videos are in the PROMAX channel on YouTube, which is accessible through the
PROMAX website at: www.promaxelectronics.com
USER'S MANUAL VERSION
Version Date Software Version
3.0 April 2013 8.0
NOTE: This user's manual describes operation for both models,
HD RANGER and
HD RANGER + . Differences between them are specified by an asterisk (*).

SAFETY RULES
* The safety could not be assured if the instructions for use are not closely
followed.
* Use this equipment connected only to systems with their negative of
measurement connected to ground potential.
* The AL-103 external DC charger is a Class I equipment, for safety reasons plug it
to a supply line with the corresponding ground terminal.
* This equipment can be used in Overvoltage Category I installations and
Pollution Degree 2 environments.
External DC charger can be used in Overvoltage Category II, installation and
Pollution Degree 1 environments.
* When using some of the following accessories use only the specified ones to ensure
safety.:
Rechargeable battery
External DC charger
Car lighter charger cable
Power cord
* Observe all specified ratings both of supply and measurement.
* Remember that voltages higher than 70 V DC or 33 V AC rms are dangerous.
* Use this instrument under the specified environmental conditions.
* When using the power adaptor, the negative of measurement is at ground
potential.
* Do not obstruct the ventilation system of the instrument.
* Use for the signal inputs/outputs, specially when working with high levels,
appropriate low radiation cables.
* Follow the cleaning instructions described in the Maintenance paragraph.
April 2013

* Symbols related with safety:
Descriptive Examples of Over-Voltage Categories
Cat I Low voltage installations isolated from the mains.
Cat II Portable domestic installations.
Cat IIIFixed domestic installations.
Cat IV Industrial installations.
April 2013

TABLE OF CONTENTS
1INTRODUCTION........................................................................................ 1-1
1.1 Description .................................................................................... 1-1
2SETTING UP............................................................................................. 2-3
2.1 Package Content ............................................................................ 2-3
2.2 Power ........................................................................................... 2-4
2.2.1 First charge................................................................................ 2-4
2.2.2 Charging the battery ................................................................... 2-4
2.2.3 Charge/discharge times............................................................... 2-5
2.2.4 Smart control battery.................................................................. 2-5
2.2.5 Usage Tips................................................................................. 2-6
2.3 Equipment Details .......................................................................... 2-7
2.4 Switching On/Off the equipment ....................................................... 2-9
2.5 Screen Icons and Dialog boxes ........................................................2-10
2.6 Menu Tree ....................................................................................2-11
2.7 Controls .......................................................................................2-14
2.7.1 Joystick....................................................................................2-14
2.7.2 Keyboard shortcuts....................................................................2-15
2.7.3 Softkeys...................................................................................2-19
2.7.4 Virtual Keyboard........................................................................2-20
2.8 StealthID Function: Signal Auto-identification....................................2-21
2.9 Equipment Settings and Configuration ..............................................2-22
2.9.1 Tune Settings Menu ...................................................................2-22
2.9.2 Video & Audio settings................................................................2-25
2.9.3 Preferences Menu ......................................................................2-26
3MEASUREMENT MODE ..............................................................................3-30
3.1 Introduction..................................................................................3-30
3.2 Operation.....................................................................................3-31
4SPECTRUM ANALYSER MODE .....................................................................4-34
4.1 Introduction..................................................................................4-34
4.2 Mode of operation..........................................................................4-34
4.3 Description in detail of the FULL SPECTRUM screen.............................4-38
4.4 Joystick Operation in SPECTRUM ANALYSER mode..............................4-39
4.5 Menu options for the SPECTRUM ANALYSER.......................................4-40
4.5.1 F1: Tuning................................................................................4-41
4.5.2 F2: Signal Parameters ................................................................4-43
4.5.3 F3: Tools..................................................................................4-44
4.5.4 F4: Advanced............................................................................4-44
4.6 Location of a signal with the SPECTRUM ANALYSER ............................4-46
April 2013

5TV MODE................................................................................................5-47
5.1 Introduction..................................................................................5-47
5.2 Operation.....................................................................................5-47
5.2.1 TV MODE: TV views....................................................................5-48
5.2.2 TV MODE: Radio views ...............................................................5-52
5.3 Menu Options for the TV MODE........................................................5-54
5.3.1 F1: Tuning................................................................................5-54
5.3.2 F2: Signal Parameters ................................................................5-54
5.3.3 F3: Service (digital signal)/Input (analogue signal).........................5-54
5.3.4 F4: Audio (digital signal)/Aspect Ratio (analogue signal) .................5-54
5.4 IRG Descriptor ..............................................................................5-55
6TOOLS ...................................................................................................6-56
6.1 Constellation.................................................................................6-56
6.1.1 Description ...............................................................................6-56
6.1.2 Operation .................................................................................6-56
6.1.3 Menu Options for Constellation tool ..............................................6-58
6.2 LTE Ingress test ............................................................................6-58
6.2.1 Description ...............................................................................6-58
6.2.2 Operation .................................................................................6-59
6.2.3 Menu options for the LTE Ingress Test tool ....................................6-61
6.3 Echoes.........................................................................................6-61
6.3.1 Description ...............................................................................6-61
6.3.2 Operation .................................................................................6-62
6.3.3 Menu Options for the Echoes tool .................................................6-64
6.4 MER by carrier ..............................................................................6-64
6.4.1 Description ...............................................................................6-64
6.4.2 Operation .................................................................................6-64
6.4.3 Menu options ............................................................................6-66
6.5 Merogram.....................................................................................6-66
6.5.1 Description ...............................................................................6-66
6.5.2 Operation .................................................................................6-66
6.5.3 Men u option.............................................................................6-68
6.6 Spectrogram.................................................................................6-68
6.6.1 Description ...............................................................................6-68
6.6.2 Operation .................................................................................6-69
6.6.3 Menu options ............................................................................6-71
6.7 Datalogger ...................................................................................6-71
6.7.1 Description ...............................................................................6-71
6.7.2 Operation .................................................................................6-72
6.8 Screenshot ...................................................................................6-76
6.8.1 Description ...............................................................................6-76
6.8.2 Operation .................................................................................6-76
6.9 Explore Channel Set.......................................................................6-77
April 2013

7INSTALLATIONS MANAGEMENT..................................................................7-80
7.1 Description ...................................................................................7-80
7.2 Operation.....................................................................................7-80
7.3 Installation Management ................................................................7-81
7.4 Create a new installation ................................................................7-84
7.5 Tools ...........................................................................................7-84
8CONNECTING TO EXTERNAL DEVICES.........................................................8-86
8.1 Mini-USB connector........................................................................8-86
8.1.1 Connecting the HD RANGER/+ (host) to an USB memory (slave)......8-86
8.1.2 Connecting a computer (host) to the HD RANGER/+ (slave).............8-87
8.2 V/A Output Connector ....................................................................8-88
8.3 V/A Input Connector ......................................................................8-88
8.4 RF Connector ................................................................................8-89
9SPECIFICATIONS .....................................................................................9-91
9.1 Specifications
HD RANGER + .........................................................9-91
9.2 Specifications
HD RANGER ...........................................................9-99
10MAINTENANCE .................................................................................... 10-106
10.1 Considerations about the Screen.................................................. 10-106
10.2 Cleaning Recommendations ........................................................ 10-106
ANNEX 1 SIGNALS DESCRIPTION.................................................................. 1
ANNEX 2 HOW TO POINT A DISH ANTENNA ...................................................15
ANNEX 3 DiSEqC COMMANDS ......................................................................23
ANNEX 4 REMOTE CONTROL COMMANDS ......................................................33
ANNEX 5 OPTICAL OPTION OP-001-PS..........................................................51
ANNEX 6 MULTIMEDIA CONTENT..................................................................62
April 2013

April 2013

TV & SATELLITE ANALYSER
HD RANGER/ +
1
1 INTRODUCTION
1.1
Description
he previous,
stylized lines to the reduction of keys
and the easy use of its interface, everything has been designed so the user has a
simple tool to use but powerful and useful.
The new
HD RANGER/ + is the sixth generation of field meters that PROMAX
launches. As each new generation, it represents an evolution from t
since it integrates the latest technological innovations and develops applications
for the new demands and needs that have emerged in recent years.
The new
HD RANGER/ + has been created with the aim to make easy the user
experience. From its ergonomic design and
Figure 1.
The
HD RANGER/ + is a universal analyser that covers several of the most
popular standards of the DVB family, as well as formats such as MPEG-2 or
MPEG-4 and Dolby audio
∗
. There is also the possibility of an extension to work in
fibre optics installations.
1
Trademark of the DVB - Digital Video Broadcasting Project.
∗
Dolby audio only available for HD RANGER +
April 2013 1-1

Besides the basic functions of TV meter and spectrum analyser for terrestrial and
satellite band, it provides additional tools, such as the detection of 4G signal
interferences (some of its working frequencies are close to the TV bands), the
diagrams constellations or the echoes detection.
The
HD RANGER/ + has an application to manage data generated at each
installation. This feature helps the user to manage information generated so he
can access it at any time or download it to a PC for further analysis.
The
HD RANGER/ + has been designed and developed entirely in the European
Union. A multidisciplinary team of highly qualified professionals has dedicated
effort and commitment to the development of a powerful, efficient and reliable
tool. During the manufacturing process, all used materials have been subjected
to a strict quality control.
In an effort to facilitate its work to professionals, our long experience ensures an
after sales quality service, which includes software updates and upgrades for
free.
Figure 2.
1-2
April 2013

2 SETTING UP
2.1
Package Content
Check that your package contains the following elements:
HD RANGER/ + Analyser.
External DC charger.
Mains cord for external DC charger.
Car lighter charger.
"F" Adapters (3 units).
• "F" / H - BNC / H Adapter.
• "F" / H - DIN / H Adapter.
• "F" / H - "F" / H Adapter.
Support belt and carrying bag.
USB On-the-go (A) Male - Mini USB (B) Male cable.
USB cable (A) Female - Mini USB (B) Male cable.
4V/RCA Jack Cable.
Transport suitcase *.
Quick Start Guide.
NOTE:Keep the original packaging, since it is specially designed to protect the
equipment. You may need it in the future to send the analyser to be
calibrated.
*Supplied only with the model. Optional Accessory on request for
.
HD RANGER +
HD RANGER
April 2013 2-3

2.2
Power
The
HD RANGER/ + is powered by a 7.2 V built-in rechargeable Li-Ion battery
of high quality and long operation time.
This equipment can operate on battery or connected to the mains using a DC
adapter. An adapter is also supplied to use with the power connector car
(cigarette lighter).
2.2.1
First charge
The equipment comes with the battery half charged. Depending on the time
elapsed from first charge and environmental conditions may have lost some of
the charge. You should check the battery level. It is advisable a first full charge.
2.2.2
Charging the battery
Connect the DC power adapter to the equipment through the power connector on
the left side panel (see figure 3).
Figure 3.
Then connect the DC power adapter to the mains via the mains cord. Ensure that
your mains voltage is compatible with the adapter voltage.
For a fast charging of the battery is necessary to switch off the equipment.
If the equipment is ON, the battery charging will be slower, depending on the
type of work you are doing. When connecting the equipment to the mains the
mains connected symbol appears inside the battery icon.
2-4
April 2013

When the equipment is connected to the mains, the CHARGER indicator remains
on. This indicator changes its colour according to the percentage of battery
charge:
RED Less than 80% of charge.
ORANGE Between 80% and 90% of charge.
GREEN 100% full charge.
When switching on the equipment, the battery voltage is checked. If the tension
is too weak to start, the LED EXT and DRAIN flashes and the equipment does not
start up. In this case please charge the battery immediately.
2.2.3
Charge/discharge times
Average charging time with the equipment off (fast charge):
3 hours to achieve an 80% charge.
5 hours to achieve a 100% charge.
With the equipment on (slow charge):
5 hours to achieve an 80% charge.
8 hours to achieve a 100% charge.
Average discharge time (with external supply disabled):
With the battery full charge the average battery time is 5:30 hours.
With the battery at 80% charge the average battery time is 4 h.
2.2.4
Smart control battery
The built-in battery of the equipment is of the "smart" type, which means that
reports its state of charge. This information is displayed inside the battery icon in
the form of the average time available. In this way the user can know at any
time the remaining battery level.
The remaining time charge that appears is calculated according to the work that
has been doing. If you activate the external supply of the equipment, the
average time would be reduced according to the increase in consumption that
occurs.
April 2013 2-5

2.2.5
Usage Tips
The battery is losing storage capacity as you go through its life. Contact your
PROMAX distributor when necessary to replace the battery.
To prolong battery life the user should follow these tips:
In case of providing a long inactivity period of the equipment it is
advisable to make every 3 months a charge / discharge cycle and a
subsequent partial charge (40% aprox.).
It is advisable to keep it in a cool place and away from heat.
You should avoid keeping the battery for a long period of time at full load
or fully discharged.
There is not necessary to wait to fully discharge before a charge because
these batteries have no memory effect.
2-6
April 2013

2.3
Equipment Details
Front View
Figure 4.
April 2013 2-7

Lateral view
Figure 5.
Top view
Figure 6.
* Optical Option.
2-8
April 2013

2.4
Switching On/Off the equipment
This analyser is designed for use as a portable equipment and it does not require
any previous installation.
►Switching On:
Slide up for a while (approximately one second) the power slide switch
located on the left side of the equipment.
When all indicators light up at once release the switch, which returns to
its rest position.
The starting display picture appears and also a progress bar that
indicates the system load.
After the system load, the last screen before shutdown appears.
►Switching Off:
Slide up for a while (approximately one second) the power slide switch
located on the left side of the equipment.
When the screen goes off release the switch, which returns to its rest
position.
The starting display picture appears and the progress bar showing the
system shutdown progress.
►Reset:
Press the key for 5 seconds. The equipment automatically turns off.
Use only in case of system crash.
In the PREFERENCES menu (press 1s), APPEARANCE tab, option "Off" the
user can activate the automatic shutdown option, selecting a waiting time (time
without pressing any key) after which the equipment turns off automatically.
April 2013 2-9

2.5
Screen Icons and Dialog boxes
On the screen are some icons that provide useful information to the user about
the current status of the instrument.
Battery charging. USB flash drive inserted.
Battery not charging.
Yellow level indicates
charge left.
LTE filter enabled.
Battery not charging,
time left indicator.
Current installation.
USB in serial port mode.
SATCR commands
enabled.
Satellite band.
Multi-function Joystick
enabled. Two-letter code
indicates the exact function:
LNB power level.
Terrestrial band.
Compressed installation.
FR Frequency tuning.
CH Channel tuning.
SP Span change.
MK Marker moving.
EC Echo/zoom change.
2-10
April 2013