ProSoft Technology AN-X-MOD User manual

AN-X-MOD (Master)
Modicon
S908 Remote I/O
Scanner Module
User Manual

Page 2 AN-X-MOD (Master) November 2011
Because of the variety of uses for the products described in this
publication, those responsible for the application and use of these
products must satisfy themselves that all necessary steps have been taken
to assure that each application and use meets all performance and safety
requirements, including any applicable laws, regulations, codes and
standards. In no event will Quest Technical Solutions be responsible or
liable for indirect or consequential damage resulting from the use or
application of these products.
Any illustrations, charts, sample programs, and layout examples shown
in this publication are intended solely for purposes of example. Since
there are many variables and requirements associated with any particular
installation, Quest Technical Solutions does not assume responsibility or
liability (to include intellectual property liability) for actual use based
upon the examples shown in this publication.
Throughout this manual we use notes to make you aware of safety
considerations.
Throughout this manual we use notes to make you aware of safety
considerations.
WARNING!
Identifies information about practices or circumstances that can lead to
personal injury or death, property damage, or economic loss.
These warnings help to:
•identify a hazard
•avoid the hazard
•recognize the consequences
IMPORTANT! Identifies information that is especially important for successful
application and understanding of the product.
TIP Identifies information that explains the best way to use the AN-X-MOD
(Master)
Microsoft is a registered trademark of Microsoft Corporation.
Windows, Windows XP Windows Vista and Windows 7 are trademarks of Microsoft Corporation.
ControlLogix, RSLinx and RSLogix 5000 are trademarks of the Allen-Bradley Company, Inc.

AN-X-MOD (MASTER) MODULE OVERVIEW 2
Hardware Features 3
Package Contents 3
Modes of Operation 3
INSTALLATION 4
Prevent Electrostatic Discharge 4
Power 4
S908 Cabling and Termination 4
Ethernet Cabling 5
Software Installation 5
QUICK START 6
ETHERNET CONFIGURATION 7
Ethernet Configuration 7
Standalone Computer 12
Reconfiguring an AN-X from an Unknown State 17
S908 NETWORK CONFIGURATION 18
Autoconfiguration 18
Manual Configuration 20
Configuration File Format 21
Viewing the Current Configuration 23
Saving the Current Configuration 23
Supported Modicon Modules 23
EXCHANGING SCHEDULED DATA WITH A CONTROLLOGIX 24
Mapping I/O Data 24

Page 4 AN-X-MOD (Master) November 2011
Other Mappable Data 27
Viewing the Current Configuration 31
Saving the Current Configuration 31
Configuring the AN-X Module in RSLogix 5000 31
Input Only Connections 33
ControlLogix Alias Tags 36
Using the ControlLogix Log 38
REDUNDANCY 40
Controller Redundancy 40
Scanner Redundancy 40
Cabling 40
ControlLogix Ethernet Configuration File 42
Aliases 44
USING ANXINIT 50
AnxInit Log 50
Locating Available AN-X Modules 51
Selecting an AN-X 52
Set AN-X IP Configuration 53
Restart an AN-X 54
AN-X Info 54
Read Kernel Parameters 55
Run Config Mode 55
Update AN-X Flash 56
Update Firmware 56
Firmware Update Wizard 56
Update Firmware Command 60
Patch Firmware 60
USING THE WEB INTERFACE 62

S908 I/O Network 63
Configure ControlLogix Support 64
View Configuration Files 65
View Active Configuration 65
Log Files 67
System Error Log 67
System Info Log 67
ControlLogix Log 67
View All Logs 67
Administration Menu 67
Browse File System 67
AN-X IP Configuration 68
Archive Configuration 69
TROUBLESHOOTING 70
LEDs 70
Ethernet LEDs 70
SYS LED 70
NET LED – Network Status 71
UPDATING THE FIRMWARE 72
Reading Version Numbers 72
SPECIFICATIONS 73
SUPPORT 74
WARRANTY 75

AN-X-MOD (Master) Module Overview
The AN-X-MOD (Master) communications module connects a
ControlLogix PLC or other device to a Modicon S908 remote I/O
network, over Ethernet.
The module acts as a scanner on the S908 network, reading inputs and
writing outputs. The module supports 800 series and Quantum remote
drops. It supports up to 32 drops.
The module supports up to 16 scheduled connections with a
ControlLogix processor, over Ethernet, so the ControlLogix processor
can read inputs from the Modicon network and write outputs.
The AN-X-MOD (Master) module has a web interface for configuration.
You can communicate with the module using any standard web browser
such as Internet Explorer.
A watchdog timer is implemented in the module’s hardware. If the
firmware does not kick the watchdog within the timeout period the
watchdog times out and places the module into a safe fatal failure state.
A jabber inhibit timer is implemented in the module’s hardware. If the
network transmitter is on longer than 150% of the longest network frame
time, the transmitter is forced off and the module is placed into a safe
fatal failure state.

AN-X-MOD (Master) Page 3
The module firmware can be updated over Ethernet using the Windows
utility supplied. Refer to page 72 for details.
Hardware Features
The module has:
•LEDs to indicate the status of the Ethernet connection, the module’s
internal state, and state of the connection to the S908 remote I/O
network
•an Ethernet connector
•a power connector
•an F connector to connect to the S908 network
Package Contents
•AN-X-MOD (Master) module
•CD containing software and documentation
•rubber feet for desktop use
Modes of Operation
There are three AN-X modes of operation:
•Boot mode. The AN-X is running its low level startup firmware.
•Configuration mode. This is the mode when you are updating the
firmware in the AN-X.
•Production mode. This is the normal runtime mode of operation.

Page 4 AN-X-MOD (Master) November 2011
Installation
Prevent Electrostatic Discharge
The module is sensitive to electrostatic discharge.
WARNING! Electrostatic discharge can damage integrated circuits or
semiconductors. Follow these guidelines when you handle the module:
•Touch a grounded object to discharge static potential
•Do not touch the connector pins
Power
AN-X requires a DC power input of anywhere from 12 to 24 VDC.
Left to right the pins on the power connector are chassis ground, negative
voltage and positive voltage.
The chassis ground should be connected.
Power consumption is 200 mA @ 12VDC or 100 mA @ 24VDC.
The part number for the power connector is Phoenix MSTB
2.5/3-ST-5.08
S908 Cabling and Termination
Refer to the Modicon Remote I/O Cable System Planning and
Installation Guide 890 USE 101 00 Version 3.0 for detailed information
on cabling and installation.
The module has a standard F connector for connection to the S908
remote I/O network.
AN-X should be connected like any other node. Ensure that the physical
ends of the S908 remote I/O network are properly terminated.
The AN-X module does not connect the S908 cable to earth ground. If a
connection to ground is required, use an F connector grounding block.

AN-X-MOD (Master) Page 5
Ethernet Cabling
AN-X has a standard RJ-45 connector for connecting to Ethernet.
If you are connecting AN-X to an existing network through a router or
switch, use a standard Ethernet cable.
If you are connecting directly between a computer and AN-X, use a
crossover cable.
Software Installation
You must uninstall any previous version of the software before you can
install a new version. Use the Windows Control Panel Add and Remove
Programs to remove the old version.
Insert the CD supplied with the AN-X module and run the program
setup.exe on the CD.

Page 6 AN-X-MOD (Master) November 2011
Quick Start
Step See page
1 Install the AN-X Windows software 5
2 Power up the AN-X, connect it to Ethernet and use
AnxInit to assign it an IP address
7
3 Connect AN-X to the Modicon S908 network 4
4 Use the AN-X web interface to autoconfigure the
Modicon network and ControlLogix configuration
18
5 Configure the AN-X in RSLogix 5000 31
6 Scan I/O, read inputs and write outputs
7 Use the web interface to create alias tags for
RSLogix 5000
36
8 Import the tags into RSLogix 5000 37
9 Use the tags to access data