Jumper Setting
SA-5800
All Rights Reserved. Copyright 2018
Safety Precaution
High Performance Intel®6th / 7th Gen. Book-Sized PC
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type recommended by the manufacturer. Dispose of used batteries per the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. Therefore we strongly
recommend qualified engineers open and disassemble the system. Access can only be gained by SERVICE
PERSONS or by USERS who have been instructed about the reasons for the restrictions applied to the
location and about any precautions that shall be taken.
The following messages are safety reminders on protecting your system from damages; hence,
extending the life of the system.
1. Check the Cable Voltage
● The operating voltage for power input should be 12V DC; otherwise, the system
may be damaged.
2. Environmental Conditions
● Place your SA-5800 on a sturdy & level surface. Be sure to allow enough space to have
easy access around the system.
● Avoid moving the system rapidly from a hot place to a cold one and vice versa because
condensation may come from inside of the system.
● Place SA-5800 in strong vibrations may cause hard disk failure.
3. Handling
● Avoid putting heavy objects on top of the system.
● Do not turn the system upside down. This may cause the hard drive to malfunction.
● If water or other liquid spills into this product, unplug the power cord immediately.
4. Good Care
● When the outside of the case is stained, remove the stain with neutral washing agent with
a dry cloth.
● If dust has been accumulated on the outside, clean the system with a special vacuum
cleaner made specially for computers.
JHDD_PWR2
JUSB2
JHDD_PWR1
JP1 VCCIO Voltage Selection
0.95V 1.0V
(default)
1
1
JP16 AT / ATX Mode
Selection
ATX
(default)
1
AT
1
1
Normal
1
(default)
Clear CMOS
JCMOS1 Clear CMOS
Data Selection
JP6 COM1 RS232/422/485
Selection
RS485
RS422
RS232
12
9
10
(default)
2
10
1
9
2
910
1
JP11 COM1 RS-485 Auto
Flow Control Selection
(default)
Disable Enable
1
1
ATX
JP2 AT / ATX Mode
Selection
(default)
1
AT
1
CPU_FAN1
CPU1
M1
4
12V
12V
GND
AUDIO1
LAN2_USB2
LAN1_USB1 VGA1
DP1 ATX_PWR1
GND
3 4
1 2
1
JP16
JP6
JP11
11
10
9
JP_COM2
JP_COM1
6
5
1
2
1 2
5 6
JP9
1
PCI_E1
1
JCMOS1
1
JP2
1
9
2
FP1
JUSB1
1
M_2_SSD
JP1
SO-DIMM1
SO-DIMM2
JP9 SPI Override Protection
Enable
(default)
1
Disable
12
1
RI
(default)
5
6
12V
COM2 Pin9 Voltage
Selection
2
1
5V
2
15
6
5
6
RI(default)
21
5 6
12V
5V
21
5 6 6
5
2
1
COM1 Pin9 Voltage
Selection
Intel
®
H110/Q170
COM2
COM1
M.2 SSD
DC_IN
JDIO1
1615
21
17
SATA2
17
SATA1
1
1
1
9
210
1
9
210
1 2
10
SYS_FAN1
1
JP7
SP1
(Buzzer)
JPWR_DIO1
1
1
4
JP12
JP10
1
Battery
1
