protech BE-0996 User manual

USER
MANUAL
BE-0996
3.5” SBC Intel®CoreTM i5-7300U /
i3-7100U / Pentium®4415U Series SoC
BE-0996 M1

BE-0996
3.5” SBC Intel® CoreTM i5-7300U /
i3-7100U / Pentium® 4415U Series SoC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Jan. 2019. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

FCC NOTICE
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approve by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the battery
is incorrectly replaced. Replace the battery
only with the
same or equivalent type recomm
ended by the manufacturer.
Dispose of used batteries according to the manufacturer’s
instructions.
WARNING: Some internal parts of the system may have high
electrical voltage. We strongly recommend that only qualified
engineers are allowed to service
and disassemble the
system. If any damages should occur on the system and are
caused by unauthorized servicing, it will not be covered by
the product warranty.

i
Contents
Revision History ............................................................................................. v
1 Introduction ......................................................................................... 1-1
1.1 About This Manual .................................................................... 1-2
2 Getting Started .................................................................................... 2-1
2.1 Packing List ............................................................................... 2-2
2.2 BE-0996 Specifications ............................................................. 2-3
2.3 Safety Precautions .................................................................... 2-5
3 Hardware Configuration ..................................................................... 3-1
3.1 JUMPER & CONNECTOR QUICK REFERENCE TABLE ........ 3-2
3.2 COMPONENT LOCATIONS ..................................................... 3-3
3.2.1 Top View of BE-0996RA-**N ............................................. 3-3
3.2.2 Jumper Setting of BE-0996RA-**N.................................... 3-4
3.2.3 Bottom View of BE-0996RA-**N ........................................ 3-5
3.2.4 I/O View of BE-0996RA-**N .............................................. 3-6
3.3 HOW TO SET JUMPERS ......................................................... 3-7
3.4 Setting Connectors and Jumpers .............................................. 3-9
3.4.1 COM2 Connector Pin9 Definition Selection Guide
(JP_COM2) ........................................................................ 3-9
3.4.2 COM Connector (COM1, COM2) .................................... 3-10
3.4.3 Dual USB 2.0 Port (USB2, USB3) ................................... 3-11
3.4.4 Internal USB 2.0 Connector (JUSB1) .............................. 3-12
3.4.5 Dual USB 3.0 Ports (USB1) ............................................ 3-13
3.4.6 LAN1, LAN2 Ports (LAN1, LAN2) .................................... 3-14
3.4.7 DP and HDMI Port (J1) .................................................... 3-15

ii
3.4.8 HD Audio Connector (AUDIO1) ....................................... 3-16
3.4.9 ATX Power Input Connector (ATX1) ................................ 3-17
3.4.10 Speaker Connectors (SPK_L_OUT1, SPK_R_OUT1) .... 3-18
3.4.11 Digital Input / Output Connector (JDIO1) ........................ 3-19
3.4.12 Front Panel Connector (JFP1) ........................................ 3-20
3.4.13 CPU Fan Connector (CPU_FAN1) .................................. 3-21
3.4.14 SATA 3.0 Connector (SATA1) .......................................... 3-22
3.4.15 SATA Power Connector (JHDD_PWR1) ......................... 3-23
3.4.16 LVDS Connector (JLVDS1) ............................................. 3-24
3.4.17 Panel Inverter Connector (JINV1) ................................... 3-25
3.4.18 Mini PCI Express Slot (M_PCIE1) ................................... 3-26
3.4.19 mSATA Connector (M_SATA1) ........................................ 3-27
3.4.20 I2C Wafer (JI2C1) ............................................................ 3-28
3.4.21 SPI Connector (JP7)........................................................ 3-28
3.4.22 SPI Override Protection Selection (JP1) ......................... 3-29
3.4.23 Battery Wafer (JBAT1) ..................................................... 3-30
3.4.24 Slide Switch For LVDS Resolution Selection (SW1) ....... 3-31
3.4.25 LVDS VCC Selection (JP5) ............................................. 3-34
3.4.26 Backlight PWM Level Selection (JP6) ............................. 3-35
3.4.27 V3P3 MPCIE Selection (JP9) .......................................... 3-36
3.4.28 Clear CMOS Data Selection (JCMOS1) .......................... 3-37
4 Software Utilities ................................................................................. 4-1
4.1 Introduction ................................................................................ 4-2
4.2 Installing Intel® Chipset Software Installation Utility .................. 4-3
4.3 Installing Graphics Driver Utility ................................................ 4-4
4.4 Installing LAN Driver Utility ........................................................ 4-5
4.5 Installing Sound Driver Utility .................................................... 4-6

iii
4.6 Intel® Management Engine Components Installer Installation .. 4-7
4.7 Installing Intel® Serial I/O Driver Utility ...................................... 4-8
5 BIOS SETUP ........................................................................................ 5-1
5.1 Introduction ................................................................................ 5-2
5.2 Accessing Setup Utility .............................................................. 5-3
5.3 Main ........................................................................................... 5-6
5.4 Advanced .................................................................................. 5-8
5.4.1 Advanced – CPU Configuration ........................................ 5-9
5.4.2 Advanced – SATA Configuration ..................................... 5-11
5.4.3 Advanced – PCH-FW Configuration ................................ 5-12
5.4.4 Advanced – Trusted Computing ...................................... 5-13
5.4.5 Advanced – ACPI Settings .............................................. 5-15
5.4.6 Advanced – F81866 Super IO Configuration .................. 5-16
5.4.7 Advanced – Hardware Monitor ........................................ 5-19
Smart Fan Mode Configuration ................................................... 5-20
5.4.8 Advanced – F81866 Watchdog ....................................... 5-21
5.4.9 Advanced – S5 RTC Wake Settings ................................ 5-22
5.4.10 Advanced – Graphic Output Protocol Policy ................... 5-25
5.4.11 Advanced – USB Configuration ....................................... 5-26
5.4.12 Advanced – Network Stack Configuration ....................... 5-27
5.5 Chipset .................................................................................... 5-29
5.5.1 Chipset – System Agent (SA) Configuration ................... 5-30
Chipset – SA Configuration – Memory Configuration .................. 5-31
5.5.2 Chipset – PCH-IO Configuration ..................................... 5-33
Chipset – PCH-IO Configuration – PCI Express Configuration... 5-34
5.6 Security ................................................................................... 5-35
5.7 Boot ......................................................................................... 5-37

iv
5.8 Save & Exit .............................................................................. 5-39
Appendix A Technical Summary ................................................A-1
BE-0996 Block Diagram ...........................................................................A-2
Interrupt Map ............................................................................................A-3
I/O Map ...................................................................................................A-14
Memory Map ...........................................................................................A-16
Configuring WatchDog Timer .................................................................A-18
Flash BIOS Update .................................................................................A-20

v
Revision History
The revision history of BE-0996 User Manual is described below:
Version No.
Revision History
Page No.
Date
M1
Initial Release
-
2019/01

BE-0996 SERIES USER MANUAL
Page: 1-1
1Introduction
This chapter provides the introduction for BE-0996 as well
as the framework of the user manual.
The following topic is included:
•About This Manual

Chapter 1 Introduction
BE-0996 SERIES USER MANUAL
Page: 1-2
1.1 About This Manual
Thank you for purchasing our BE-0996 3.5 ”SBC Intel® CoreTM i5-7300U /
i3-7100U / Pentium® 4415U Series SoC. The BE-0996 provides faster processing
speed, greater expandability and can handle more tasks than before. This manual
contains 5 chapters and 1 appendix. Users can configure BE-0996 according to their
own needs. This user manual is intended for service personnel with strong hardware
background. It is not intended for general users.
The following section outlines the structure of this user manual.
Chapter 1 Introduction
This chapter provides the introduction for BE-0996 as well as the framework of the
user manual.
Chapter 2 Getting Started
This chapter describes the package contents and outlines BE-0996 specifications.
Read the safety reminders carefully on how to take care of BE-0996 motherboard
properly.
Chapter 3 Hardware Configuration
This chapter outlines the locations of BE-0996 motherboard components and their
respective functions. You will learn how to set the jumpers and configure BE-0996 to
meet your own needs.
Chapter 4 Software Utilities
This chapter contains helpful information for proper installations of the Intel Chipset
Software Installation Utility, Intel® Management Engine Components Installer,
USB 3.0 eXtensible Host Controller Utility, Graphics Driver Utility, LAN Driver
Utility, Sound Driver Utility and Hotfix Driver Utility.
Chapter 5 BIOS Setup
This chapter indicates you how to change the BIOS configurations.
Appendix A Technical Summary
This appendix provides the information about the allocation maps for BE-0996 block
diagram, BE-0996 motherboard resources, Watchdog Timer Configuration and Flash
BIOS Update.

BE-0996 SERIES USER MANUAL
Page: 2-1
2 Getting Started
This chapter provides the information for BE-0996
motherboard. It describes the package contents and outlines
the motherboard specifications.
The following topics are included:
• Package List
• BE-0996 Specification
• Safety Precautions
Experienced users can go to Chapter 3 Hardware
Configuration on page 3-1 for a quick start.

Chapter 2 Getting Started
BE-0996 SERIES USER MANUAL
Page: 2-2
2.1 Packing List
If you discover any of the items listed below are damaged or list, please
contact your local distributor immediately.
Item
Q’ty
BE-0996
1
Quick Reference Guide
1
Manual / Driver DVD
1
Mini Jumper (2.0 mm)
6
SATA & SATA Power Cable (150mm)
1

Chapter 2 Getting Started
BE-0996 SERIES USER MANUAL
Page: 2-3
2.2 BE-0996 Specifications
Main Board
CPU
Support
Intel®Kabylake U Series
Intel® Core® i5-7300U
Intel® Core® i3-7100U
Intel
®
Pentium
®
4415U
Memory Support
1 x DDR4 SO-DIMM sockets (up to 16GB)
Power Supply
4-pin ATX Power Input Connector (12V / 24V)
Expansion Slots

1 x full-sized mSATA slot
1 x full-sized mPCIe
slot
SATA
1 x SATAIII (6.0Gb/s)
Operating System
Windows 10 64bit / Ubuntu 16.04 64bit
Dimensions
102 x 145mm (3.5" SBC)
Certificate
FCC / CE
I/O Ports
Display
1 x DP (rear I/O)
1 x HDMI (rear I/O)
1 x LVDS (internal I/O)
USB
For Core-i5 / i3 SKU:
2 x USB 2.0 (internal wafer)
2 x USB 3.0 (rear I/O), 4 x USB 2.0 (rear I/O)
For Pentium SKU:
1 x USB 2.0 (internal wafer)

2 x USB 3.0 (rear I/O), 4 x USB 2.0 (rear I/O)
Audio
Line In, Line Out, Mic In (pin header)
2 x CH Audio AMP (L&R), 2W
LAN

2 x GbE LANs, Wake-on-LAN
LAN1: Intel
®
I219 LM / LAN2: Intel
®
I211 AT
Serial Ports
Onboard pin header:
COM1 for RS-232
COM2 for RS-232/422/485 selectable under BIOS
(default: RS-232)
DIO Port
1 x DIO ( 8 in / 8 out) (pin header)
Expansion Slots
For Core-i5 / i3 SKU:
1 x full-sized mSATA slot (with USB signal)
1 x full-sized mPCIe slot (with SATA / USB signal)
For Pentium SKU:
1 x full-sized mSATA slot (with SATA signal only)
1 x full-sized mPCIe slot (with PCIe / USB signal)
only)
I2C Port

1 x I2C port

Chapter 2 Getting Started
BE-0996 SERIES USER MANUAL
Page: 2-4
Environment
Operating Temperature
0°C ~ 60°C (32°F~ 140°F)
Storage Temperature
-40°C ~ 80°C (-40°F~ 185°F)
Humidity
20%~ 95%

Chapter 2 Getting Started
BE-0996 SERIES USER MANUAL
Page: 2-5
2.3 Safety Precautions
Follow the instructions below to avoid your system from damages:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Do not touch any components of this board when it
is powered on. Always disconnect power when the system is not in use.
3. Disconnect power source when you change any hardware devices.
For instance, when you connect a jumper or install any cards, a surge of
power may damage the electronic components or the whole system.

BE-0996 SERIES USER MANUAL
Page: 3-1
3 Hardware Configuration
This chapter contains helpful information about the jumper
& connector settings, and component locations.
The following sections are included:
• Jumper & Connector Quick Reference Table
• Component Locations
• Connector Configuration and Jumper Settings
• Connector Pin Assignments

Chapter 3 Hardware Configuration
BE-0996 SERIES USER MANUAL
Page: 3-2
3.1 JUMPER & CONNECTOR QUICK REFERENCE TABLE
JUMPER Description
NAME
COM2 Pin9 RI/5V/12V Selection
JP_COM2
Clear CMOS Data Selection
JCMOS1
SPI Override Protection Selection
JP1
LVDS VCC Selection
JP5
Backlight PWM Level Selection
JP6
V3P3 MPCIE Selection
JP9
Slide Switch For LVDS Resolution
Selection
SW1
CONNECTOR Description
NAME
COM Connectors (Onboard Pin
Header)
COM1, COM2
Dual USB 2.0 Port
USB2, USB3
Dual USB 3.0 Ports
USB1
2 x LAN Ports
LAN1, LAN2
Internal USB 2.0 Connector
JUSB1
DP and HDMI Port
J1
HD Audio Connector
AUDIO1
ATX Power Input Connector
AT X 1
Speaker Connectors
SPK_L_OUT1, SPK_R_OUT1
Digital Input / Output Connector
JDIO1
Front Panel Connector
JFP1
CPU Fan Connector
CPU_FAN1
SATA 3.0 Connector
SATA 1
SATA Power Connector
JHDD_PWR1
LVDS Connector
JLVDS1
Panel Inverter Connector
JINV1
Mini PCI Express Slot
M_PCIE1
mSATA Connector
M _ S ATA 1
I2C Wafer
JI2C1
Battery Wafer
J B AT 1
SPI Connector
JP7
DDR4 SO-DIMM Memory Socket 1
DIMM1

Chapter 3 Hardware Configuration
BE-0996 SERIES USER MANUAL
Page: 3-3
3.2 COMPONENT LOCATIONS
3.2.1 Top View of BE-0996RA-**N
WARNING: Always disconnect the power cord when
you are working with connectors and jumpers on
BE-0996. Make sure both the system and peripheral
devices are turned OFF as sudden surge of power
could damage
sensitive components. Make sure
BE-0996 is properly grounded.
CAUTION:
Observe precautions while handling
electrostatic sensitive components. Make
sure to
ground yourself to prevent static charge while you are
working on the connectors and jumpers. U
se a
grounding wrist strap and place all electronic
components in any static-shielded devices.
CAUTION: Always touch BE-0996
components by
the edges. Never touch components such as the
processor by its pins. Take special cares while you
are holding elec
tronic circuit boards by the edges
only. Do not touch BE-0996 components.
DP
HDMI LAN2 LAN1 USB 3.0
USB 2.0
SATA 3.0
Mini PCIe
mSATA
Inverter
Connector
I2C
Connector
LVDS
Connector
SATA Power
Connector
DDR4
SO-DIMM Front Panel USB 2.0
Connector
CPU Fan
Connector
ATX Power
Input Connector
12V/24V
COM2
8DI+8DO
COM1
Audio
Battery
Connector
Speaker Connector
(Left)
Speaker Connector
(Right)
SPI

Chapter 3 Hardware Configuration
BE-0996 SERIES USER MANUAL
Page: 3-4
3.2.2 Jumper Setting of BE-0996RA-**N
JP9 V3P3 MPCIE Setting
(default)VCC3_3
1 1
V3P3A
JP1 SPI Override Protection
Enable
1
JCMOS1 Clear CMOS Data
Selection
JP6 Backlight PWM Level
Selection
1
5V
(default)
3.3V
1
Disable
(default)
1
JP5 LVDS VCC Selection
5V
1
(default)
3.3V
1
Normal
(default)
1
Clear CMOS
1
12V
56
12
JP_COM2 Port RI & Voltage
Selection
RI
(default)
6
2
5
12
5V
6 5
12
J1(DP+HDMI)
AUDIO1
LAN2 LAN1 USB1 USB2 USB3
JP9
1
JBAT1
1
1
JCMOS1
SATA 1
1
JLVDS1
2
29
SW1
1
4
8
5
JP7
1 2
78
1
JFP1 JUSB1
1
2
9
10
1
28
9
1
JP1
CPU_FAN1
1
ATX1
3
4
1
2
COM1
COM2
JP_COM2
6
9
6
9
12
65
DIMM1
M_PCIE1
M_SATA1
1
2
9
10
JDIO1
12
19
1
5
1
5
20
SPK_R_OUT1
JINV1JI2C1
1
JP6
1
1
30
1
JP5
1
JHDD_PWR1
Pins 1, 8: ON Pins 2, 7: OFF
Pins 3, 6: ON Pins 4, 5: ON
1024x768 Channel S/8bit
(Default)
SW1 LVDS Resolution
Selection
1
4
8
5
800x600 Channel S/6bit
Pins 1, 8: ON Pins 2, 7: ON
Pins 3, 6: ON Pins 4, 5: ON
1
SPK_L_OUT1
1

Chapter 3 Hardware Configuration
BE-0996 SERIES USER MANUAL
Page: 3-5
3.2.3 Bottom View of BE-0996RA-**N