Pyle PDMW420PG User manual

INSTRUCTION
MANUAL
WIRELESS SYSTEM
POWER AF PEAK
DIVERSITY
B
A
Diversity
Wireless Mic. Receiver
PLL

CONTENTS
Thank you for your kind using our wireless microphone
with receiver. Before using the machine please read
the instruction manual very carefully. According to our
instruction manual for ensure you using of the best
function and performance. lf any defect please contact
with our agent or dealer. lt is our pleasure to serve you.
Thank you for your cooperation
CHARACTER
SPECIFICATIONS
NAMES OF PARTS
INSTALLATION
POWER SUPPLY CONNECTION
SQUELCH CONTROL AND VOLUME CONTROL
UNBAL OUT AND BALANLED OUT
INDICATOR ANDINSTALL ANTENNA
NOTE
2
2
3
4
4
5
6
7
8
ENGLISH
1
KEEP AWAY RAINING OR
SUN SHINE.
BE CAREFUL, DON'T DROP
OFF THE MICROPHONE TO
FLOOR.
THE WIRELESS RECEIVER
LOCATED AT GOOD CONDITION
PLACE.
NOTE
10
RECEPTEUR :
1m
1m
40-60m
RECEPTEUR
1m
ENGLISH

IF YOU ARE NOT TECHNICAL ENGINEER PLS. DO NOT MODI-
FIED OR KNOCK - DOWN IT.
NOTE
9
ENGLISH
Specifications :
Character :
antenna.
LED lndicator (Power , Diversity (A---B),Peak) and telescopic
Compact, lightweight, single-channel receiver.
780~865Mhz.
UHF band frequency by PLL synthesized oscillator. Range from
Compander circuit for expending dynamic range.
Special circuit design to delete microphone switch ON/OFF noise.
Audio output connect with XLR balanced and mono phone jack
unbalanced.
2
ENGLISH
Weight
Dimensions
Squelch
Audio Output
Frequency Response
S/N proportion
Sensitivity
T.H.D.
Deviation maximum
Oscillation Mode
Carrier Frequence Range
Reception mode
Stabilite
Portee de dynamique
Power Supply
600g
1.32 lb
295(W) 114(D) 40(H) mm
0.97(W) 0.37(D) 0.13(H)ft
1. Unbalanced 6.3mm phone jack 750mV/5K
2. XLR Balanced output 70mV/600
3uv pour 20dB SINAD
50Hz-15KHz 3dB
Tone Key (Tone frequency : 32.768KHz)
External Control
>100dB At 15KHz de Deviation
<1%
40/50KHz
0.005% /25 C
UHF 780~865 MHz
Diversity model
PLL synthesized oscillator
>100 dBm
DC 12V-15V 300mA
With AC/DC Adaptor

3
NAME OF PARTS
4. Telescopic Antenna.
3. Audio Peak Indicator.
2. Mic. ON and Diversity Signal Indicators.
1. Power ON Indicator.
ENGLISH
POWER AF PEAK
DIVERSITY
B
A
1
2
3
4
8. Squelch Control
This control is factory present,
SQ noisy controlled adjustment,
Before you turn-on the receirer,
at first. The receiver already
have been jamming by outside
signal. Please adjust SQ con-
trol until the jamming signal
has disappeared. (Clock-wise)
8
INSTRUCTION MANUAL
FIG.8
FIG.7
SQUELCH
MAX.
SENS.
a. Power ON lndicator:
This red light glows. When
the DC supply and power
Switch ON. It indicates that
the receiver is on.
b. Reception Indicator:
This indicator does light
during standby. When
microphone signal is
received, The green or
yellow indicator light to
indicate the reception of
microphone.
c. Audio peak Indicator:
This red light flickers when
the audio signal from the
microphone approaches
the overload clipping level.
It is affected by the tran-
smitter gain control setting
and the loudness of your
voice.
7. Indicator
POWERAFPEAK
DIVERSITY
B
A
ENGLISH
Diversity
WirelessMic. Receiver
PLL

7
INSTRUCTION MANUAL
6. Balance output XLR or
CANNON Connection
Cable insert to balance soc-
ket output connecting with
mixer or amplifier MIKE IN.
BALANCE
MIKE INPUT
FIG.6
5. Audio Output Connector
You can connect an unbala-
nced audio cable with a 1/4
inch phone plug between this
connector and your mixer or
amplifier input.
FIG.5
UNBAL
IN
BALANCE
MICRO
AUX
AUDIO OUTPUT
BALANCE
MICRO
AUX
AUDIO OUTPUT
ENGLISH
NAME OF PARTS
11. Balance Socket.
10. Audio output Connector.
9. Volume. Control.
8. Squelch Control.
7. Channel selector switch.
6. DC. Jacket.
5. Power Switch.
4
POWER
ON OFF
DC IN
SQUELCH
MAX.
VOLUME
AUX
-
+
BALANCE
MICRO
AUX
AUDIO OUTPUT
MAX.
SENS.
1089 11
56
ENGLISH
13 5
1
9
7
15 3
11
7

4.Volume Adjustor
The purpose of this control is
to give the ability to provide
an audio outputlevel from the
wireless system that is similar
to that of a wired microphone.
3.Install Antenna.
Receivers signals from the transmitter. Make sure the antenna is
fully extended vertically.
6
FIG.4
INSTRUCTION MANUAL
MAX.
VOLUME
AUX
POWER
ON OFF
DC IN
SQUELCH
MAX.
VOLUME
AUX
-
+
BALANCE
MICRO
AUX
AUDIO OUTPUT
MAX.
SENS.
4545
ENGLISH
2.Power Supply Connection
Use DC power supply could
switch with adaptor supply or
batter of 12-18V DC.
Connection DC supply, DC
plug connection with "DC-IN"
socket. (see FiG2) another
plug terminal connection with
battery or power supply.
5
FIG.2
FIG.1
IN
INSTRUCTION MANUAL
POWER
ON OFF
POWER
ON OFF
DC IN
-
+
ENGLISH
13 5
1
9
7
15 3
11
1.Power Switch
Mark sure the correct voltage.
push this power switch once
to turn on; If unit still fails to
operate, Secure a qualified
technician or contact us for a
Return Authorization prior to.
Shipment. Disconnect power
supply before removivg re-
ceiver cover. If you want to have
a different frequency, set the
receiver and transmitter power
SW to OFF before you do.