Pyle PDWM2700 User manual

TwoChannelVHFWirelessMicrophoneSystem
PDWM2700
Handheld Microphone, Headset Microphone
and Belt Pack Transmitter

www.PyleUSA.com
2
We strongly suggest that you carefully study these instructions before attampting to operate the system.
We also recommend that you keep this manual in a safe and handy place for future reference.
PRECAUTIONS
• Avoid expose of the system to rain or moisture.
• No user-serviceable parts inside the system. Refer all servicing to qualied Technician only.
• Handle the wireless system carefully, dropping or other shocks may cause failure.
• Avoid using the system where it may be subjected to heat, such as direct sunlight near radiators or other heat sources.
• Should any liquid be spilt on the arrangement, stop using it immediately. It may be possible to dry the system, but
you should have it checked by a qualied technician before using it again.
• Use the provided adapter only. Do not attempt to service or repair the device yourself. Refer all servicing to qualied
service personnel. Do not attempt to modify the device in anyway. Doing so could invalidate your warranty.
• Only use tile system with the supplied components, do not attempt to use any other power supply adapter or
microphone.
• If you don't use the system for long time, please remove the batteries from the microphone and unplug the receiver.
• Only replace the battery with the same or an equivalent type.
• Do not use any solvents to clean any part of the microphone system.

www.PyleUSA.com
3
HANDHELD MICROPHONE
1. Unscrew the battery cover at the end of the microphone. Install the provided 9 volt battery and then close the
cover. Make sure to connect with the correct polarity.
2. Move power switch to ON position. Power LED indicator will ash once and then go off. This indicates correct
operation. If power LED indicator lights red, this indicates the battery is low. Please replace with new battery.
3. Move power switch to middle to mute the microphone.
4.If the microphone is not going to be used for long time, please take out the battery to prevent damage and battery
leakage.

www.PyleUSA.com
4
BODYPACK TRANSMITTER
1. Slide up the battery cover in the front of the body pack as per above sketch. Install the provided 9 volt battery and
the battery cover. Make sure to connect with the correct polarity.
2. Move power switch to ON position. Power LED indicator will ash once and then go off. This indicates correct operation.
If power LED Indicator lights red, this Indicates the battery is low. Please replace with new battery.
3. Move microphone switch to middle to mute the microphone.
4. Adjust the volume control to you gat the sufficient sound from your speaker.
5. If the microphone is not going to be used for long time, please take out the battery to prevent damage and battery
leakage.

www.PyleUSA.com
5
RECEIVER
1. Switch on the wireless microphone receiver unit by pressing the POWER switch and the POWER light will illuminate
to show the receiver unit Is working.
2. Fully extend the antenna to the maximum length.
3. Switch ON the transmitter. Power LED indicator will ash once the turned off. When the microphone is ON, the
receiver RF indicator will light.
4. Adjust the volume and tone levels of your amplier system as well as the receiver & the body peck required.
5. When the transmitter is not going to be used for long time, please take out the battery from transmitter.
Note that switching the microphone on and o can cause interference that will be heard if the microphone volume
level of the amplier system is still set high.

www.PyleUSA.com
6
INSTALLATION
To connect the wireless microphone to your amplier system:
• Refer to above installation diagram.
• Using the supplied 6.35mm to 6.35mm lead, connect the AF OUT jack of the receiver to the MIC INPUT socket on
your amplier.
• Plug one end of the mains power adapter into a suitable electricity socket. Plug the other end of the adapter into
receiver DC 12V input socket.

www.PyleUSA.com
7
TROUBLESHOOTING
Please read and check the following points before asking for service.
The wireless microphone is not work:
• Check the microphone battery by switching the microphone ON.
If power LED indicator lights red, replace the battery.
• Check the POWER Indicator on the receiver unit Is ON. If not, check the power adapter if rmly plugged into a
working electricity socket.
• Check if the amplier system is ON and the microphone volume controls were set correctly.
• Check if the microphone jack lead is rmly connected into the output socket on the rear panel of the receiver unit
and insert the MIC input socket on your amplier.
The working range is limited:
• Check the microphone battery condition(see above)
• Check the antenna are fully extended.Adjust the position of the antenna to achieve the best reception.
• Check the settings of the microphone controls on the amplier. Adjust volume end tone to get the beat sound
without any feedback.

www.PyleUSA.com
8
SPECIFICATIONS
A. Overall system
1. Oscillation mode:
2. Carrier Frequency Range:
3. Frequency Stability:
4. Max Deviation:
5. Dynamic Range:
6. S/N Rate:
7. T.H.D:
8. Frequency Response:
9. Operating Range:
B. Receiver
1. Sensitivity:
2. Image Rejection:
3. Stability:
4. Audio Output:
5. Power Supply:
Quartz Control
VHF 160-270MHz
+1-0.005%
+1-56KHz with level limiting
>110dB
>100dB
<0.5dB
100Hz-15KHz
up to 150 ft
6dB µ V at SIN >70dB
>60dB
>80dB
-12db/600ohm unbalanced
12V500mA

www.PyleUSA.com
9
C.Transmitter
1. Mike capsule:
2. Antenna:
3. RF Output:
4. Spurious:
5. Power Supply:
Handheld: dynamic
Headset or lavalier MIC: condenser
Built-in housing (Handheld MIC)
External (Belt pack)
<10mW
<-40dBC
9V battery

Questions? Issues?
We are here to help!
Phone: [phone]
Email: suppor[email protected]om