Pyramid TIMETRAX SYNC PoE User manual

TIMETRAX™ SYNC PoE DIGITAL CLOCK
Installation Instructions
OVERVIEW
ETHERNET
Thank you for choosing a TimeTrax™ Sync PoE Clock System. The TimeTrax™ PoE Clock System is capable of receiving
both its time and power from a cost-effective and reliable Power over Ethernet source.
The POE Analog Clock may be powered by the Ethernet (see PoE Switch Method-pg. 2). An alternative method is to
use a standard Ethernet Switch in combination with a PoE port injector (see NON-PoE Switch Method-pg 3).
IMPORTANT: Prior to clock installation, install TimeTrax™ Sync software (part # SASDLCWDXX separately).
Before clock installation, please remove security bracket from back of clock (see instructions below).
For more information, visit pyramidtimesystems.com or call our technical support team at 888.479.7264 during
regular business hours: 8am-5pm EST, M-F.
SECURITY BRACKET REMOVAL
Prior to installation, detach metal security bracket from clock by inserting included release key into slot
located on back of clock.
Push key all the way into slot. Key will slide easily until some resistance from locking tab is felt.
With key fully engaged, slide the security bracket down and off of the clock.
I2253
Page 1 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC PoE DIGITAL CLOCK
Installation Instructions (cont.)
PoE SWITCH METHOD
Connect CAT-5E Ethernet cable (sold separately) into RJ-45 Ethernet port located on back of clock. If using
standard electrical box mounting method, please advance to step 3.
If not using electrical box, hold security bracket flush against wall, level & mark four screw holes close to
corner tabs. Drill holes as marked and secure bracket to wall using provided screws and wall anchors. Drill
hole centered in square opening of bracket. The hole should be large enough to route Ethernet cable
through wall. Advance to step 4.
If using electrical box, install metal security bracket onto a standard electrical box.
Route the CAT 5E Ethernet cable through the square opening of security bracket. Pull cable to Ethernet
switch.
Push clock onto security bracket aligning four tabs on bracket with four matching slots on back of terminal.
Slide clock downward until locking tab clicks into place. When properly mounted, clock cannot be slid up
and off bracket without using included wall bracket release key to disengage locking tab.
Connect free end of CAT-5E Ethernet cable into Power over Ethernet Switch (sold separately).
Upon successful connection, clock will display . Accurate time will display after 1-2 minutes.
Run TimeTrax™ Sync software to begin “DEVICE DISCOVERY” and customize configurations. (refer to
software User Guide).
DIGITAL CLOCK
SECURITY BRACKET
CAT-5E CABLE
ETHERNET SWITCH
I2253
Page 2 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC PoE DIGITAL CLOCK
Installation Instructions (cont.)
NON-PoE SWITCH METHOD
Connect CAT-5E Ethernet cable (sold separately) into Ethernet RJ-45 port located on back of clock. If using
standard electrical box mounting method, please advance to step 3.
If not using electrical box, hold security bracket flush against wall, level & mark four screw holes close to
corner tabs. Drill holes as marked and secure bracket to wall using provided screws and wall anchors. Drill
hole centered in square opening of bracket. The hole should be large enough to route Ethernet cable
through wall. Advance to step 4.
If using electrical box, install metal security bracket onto a standard electrical box.
Route the CAT-5E Ethernet cable through the square opening of security bracket, or if preferred pull cable
directly to Ethernet PoE Port Injector (part #APOEPI sold separately). Connect free end of CATE-5E Ethernet
cable into Ethernet Port Injector “LAN +DC” port. Plug Ethernet Port Injector into standard wall outlet.
Push clock onto security bracket aligning four tabs on bracket with four matching slots on back of terminal.
Slide clock downward until locking tab clicks into place. When properly mounted, clock cannot be slid up
and off bracket without using included wall bracket release key to disengage locking tab.
Connect another CAT-5E Ethernet cable (sold separately) into Ethernet Port Injector “LAN” port. Connect
free end of CAT-5E Ethernet cable into Ethernet Switch.
Upon successful connection, clock will display . Accurate time will display after 1-2 minutes.
Run TimeTrax™ Sync software to begin “DEVICE DISCOVERY” and customize configurations. (refer to
software User Guide).
SECURITY BRACKET
ETHERNET SWITCH
DIGITAL CLOCK
CAT-5E
ETHERNET CABLE
CAT-5E
ETHERNET CABLE
I2253
Page 3 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC PoE DIGITAL CLOCK
Installation Instructions (cont.)
Time Base
Microprocessor
Time Update
Frequency
Configurable ( 1/minute –1/week)
Method
NTP time server
ETHERNET RJ 45
CORD
Power Input
48VDC
105-120 VAC
Average Power
Consumption
4.848 Watts
5.6 Watts
Operating Temp
-30°F (-34.44°C) to 130°F (54.44°C)
Warranty
3-Year manufacturer’s limited warranty
Guarantee
30-Day money back guarantee
Compliance
IEEE 802.3af/ANSI X3.263
Includes
Security mounting bracket & key, wall mounting
template, security mounting bracket template
DISPLAY
Display Format
12 or 24 hour mode
Digits
7 segment LED digits
Visibility
100ft (30.5m) 2.5in digit height
200ft (60.96m) 3in digit height
250ft (76.05m) 4in digit height
LED Color
Red
CASE
Case
Smooth surface 94VO/5VA ABS
Bezel Color
Black or Silver
Lens
Shatterproof, side molded, polished polycarbonate
crystal
Mounting
Wall, Dual Wall, Dual Ceiling
CHARACTER
HEIGHT/DIGITS
WEIGHT
DIMENSIONS
(WXHXD)
2.5in/6-digit
1.5lbs (0.680kg)
11.25in x 4.5in x 1.5in
(28.25cm x 11.5cm x 3.75cm)
3in/4-digit
1.5lbs (0.680kg)
11.25in x 4.5inx1.5in
4in/4-digit
1.9lbs (0.861kg)
11.5in x 6.25in x 1.5in
(29cm x 15.75cm x 3.75cm)
4in/6-digit
2.3lbs (1.043kg)
15.5in x 6.25in x 1.5in
(39cm x 15.75cm x 3.75cm)
SPECIFICATIONS
I2253
Page 4 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC PoE DIGITAL CLOCK
Installation Instructions (cont.)
PART#
DESCRIPTION
SASDLCWDXX*
TimeTrax™ Sync Software
APOEPI
Ethernet Port Injector & 6ft power cable
42227-1
20ft Category 5E Ethernet Cable
42321
Dual Digital Clock Wall Bracket (3x4/2.5x6/4x4)
42422
Dual Digital Clock Wall Bracket (4x6)
42443
Dual Analog & Digital Ceiling Bracket
42316
4in x 6 digit Digital Clock Chrome Wire Guard
42400
4in x 4 digit Digital Clock Chrome Wire Guard
42689
Digital Clock Wash-Down Enclosure
42247
Digital Security Mount Replacement
42281
Wall Clock Security Mount Replacement Key
*Required for clock synchronization.
3-YEAR LIMITED WARRANTY
Pyramid warranties its Synchronized Clock System to the original user against defective material or workmanship for
a period of 3 years from date of purchase.
The manufacturer’s responsibility under this Warranty is limited to repair or replacement of defective part or parts.
Pyramid reserves the right to determine whether parts failed because of defective material, workmanship, or other
causes. Failure caused by accident, alteration, misuse or improper packaging of returned unit is not covered by this
Warranty. Any repair to equipment other than by Pyramid voids the Warranty. Users in territories other than USA,
Canada, South America & Australia should contact the Dealer from whom the unit was purchased. The rights under
this Warranty are limited to original user and may not be transferred to subsequent users.
If Customer Support cannot troubleshoot your problem over the phone, we will replace your unit free of charge if it
is within warranty period. Please contact Customer Support at 888.479.7264 between the hours of 8am-5pmEST for
details.
Should you need to speak live to one our representatives, please call toll-free (US/Canada) at 888.479.7264 during
regular business hours: 8am-5pmEST, Monday-Friday.
I2253
Page 5 of 5
888.479.7264
pyramidtimesystem.com
ACCESSORIES
WARRANTY
TECHNICAL SUPPORT