Pyramid TIMETRAX SYNC RF User manual

TIMETRAX™ SYNC RF WIRELESS DIGITAL CLOCK
Installation Instructions
OVERVIEW
ETHERNET
Thank you for choosing a TimeTrax™ Sync RF Wireless Clock System. The TimeTrax™ RF Wireless Clock System
receives dependable, accurate time from the TimeTrax™ Sync RF Wireless Transmitter.
IMPORTANT: Prior to clock installation, install TimeTrax™ Sync RF Wireless Transmitter and complete software
set-up (part #9T1WI or S9DWXSLAUB sold separately).
IMPORTANT: WIRING SHOULD BE COMPLETED PER ELECTRICAL CODE AND PERFORMED BY A LICENSED
ELECTRICIAN. Before clock installation, please remove security bracket from back of clock (see instructions below).
For more information, visit pyramidtimesystems.com or call our technical support team at 888.479.7264 during
regular business hours: 8am-5pm EST, M-F.
SECURITY BRACKET REMOVAL
Prior to installation, detach metal security bracket from clock by inserting included release key into slot
located on back of clock.
Push key all the way into slot. Key will slide easily until some resistance from locking tab is felt.
With key fully engaged, slide the security bracket down and off of the clock.
I2255
Page 1 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC RF WIRELESS DIGITAL CLOCK
Installation Instructions (cont.)
WIRED MODELS
WIRING SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN AND IN COMPLIANCE WITH ELECTRICAL CODE.
Install metal security bracket onto a standard electrical box.
Make electrical connections. This should only be performed by a licensed electrician.
Push clock onto security bracket aligning four tabs on bracket with four matching slots on back of terminal.
Slide clock downward until locking tab clicks into place. When properly mounted, clock cannot be slid up
and off bracket without using included wall bracket release key to disengage locking tab.
Upon power up, clock will initially display . Clock will synchronize to the RF Wireless Transmitter
immediately upon receiving a radio signal (typically 1-2 minutes).
I2255
Page 2 of 5
888.479.7264
pyramidtimesystem.com
CORD MODELS
Install metal security bracket onto a standard electrical box, or if not using electrical box, hold security
bracket flush against wall, level & mark four screw holes close to corner tabs. Drill holes as marked and
secure bracket to wall using provided screws and wall anchors.
Feed cord through channel located at bottom of clock.
Hang clock on security bracket (see step 3 above).
Plug clock into standard electrical wall outlet. Upon power up, clock will initially display . Clock will
synchronize to the RF Wireless Transmitter immediately upon receiving a radio signal (typically 1-2
minutes).

TIMETRAX™ SYNC RF WIRELESS DIGITAL CLOCK
Installation Instructions (cont.)
Install metal security bracket onto a standard electrical box, or if not using electrical box, hold security
bracket flush against wall, level & mark four screw holes close to corner tabs. Drill holes as marked and
secure bracket to wall using provided screws and wall anchors.
Install two lithium C size batteries (part #42224 sold separately) into compartment on back of clock. Clock
will initially display .. Clock will synchronize to the RF Wireless Transmitter immediately upon
receiving a radio signal (typically 1-2 minutes).
Push clock onto security bracket aligning four tabs on bracket with four matching slots on back of terminal.
Slide clock downward until locking tab clicks into place. When properly mounted, clock cannot be slid up
and off bracket without using included wall bracket release key to disengage locking tab (see page 2 for
diagram).
BATTERY MODELS (LCD)
I2255
Page 3 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC RF WIRELESS DIGITAL CLOCK
Installation Instructions (cont.)
Time Base
Microprocessor
AC POWER & CORD
LCD BATTERY
Time Update
Frequency
Every 20 seconds
Every 24 Hours (2am)
Method
902-928 MHz frequency-hopping technology
FLYING LEAD
CORD
LCD BATTERY
Power Input
105/240 VAC
or 24/36
VAC/VDC
105-120 VAC
(2) 3.6 Volt
Lithium
Batteries
Average Power
Consumption
5.1 Watts
5.7 Watts
5 Years
(typical)
Operating Temp
-30°F (-34.44°C) to 130°F (54.44°C)
Warranty
3-Year manufacturer’s limited warranty
Guarantee
30-Day money back guarantee
Compliance
FCC part 15 section 15,247
FCC ID#WC7H9ALG1
Includes
Security mounting bracket & key, wall mounting
template, security mounting bracket template
DISPLAY
Display Format
12 or 24 hour mode
Digits
7 segment LED digits (Flying Lead & Cord)
7 segment LCD digits (LCD Battery Operated)
Visibility
75ft (22.85m) 2.5in LCD digit height
100ft (30.5m) 2.5in LED digit height
200ft (60.96m) 3in LED digit height
250ft (76.05m) 4in LED digit height
LED Color
Red
LCD Color
Black
CASE
Case
Smooth surface 94VO/5VA ABS
Bezel Color
Black or Silver (LCD Black only)
Lens
Shatterproof, side molded, polished polycarbonate
crystal
Mounting
Wall, Dual Wall, Dual Ceiling
CHARACTER
HEIGHT/DIGITS
WEIGHT
DIMENSIONS
(WXHXD)
2.5in/6-digit
1.5lbs (0.680kg)
11.25in x 4.5in x 1.5in
(28.25cm x 11.5cm x 3.75cm)
3in/4-digit
1.5lbs (0.680kg)
11.25in x 4.5inx1.5in
4in/4-digit
1.9lbs (0.861kg)
11.5in x 6.25in x 1.5in
(29cm x 15.75cm x 3.75cm)
4in/6-digit
2.3lbs (1.043kg)
15.5in x 6.25in x 1.5in
(39cm x 15.75cm x 3.75cm)
SPECIFICATIONS
I2255
Page 4 of 5
888.479.7264
pyramidtimesystem.com

TIMETRAX™ SYNC RF WIRELESS DIGITAL CLOCK
Installation Instructions (cont.)
PART#
DESCRIPTION
S9DWXLAUB*
Ethernet Wireless RF Transmitter, wall mount
(includes software)
9T1WI*
Ethernet Wireless RF Transmitter, shelf mount
(includes software)
42337
Ethernet Wireless RF Transmitter, wall mount
(secondary, no software)
S9DSXOLAUB
Ethernet Wireless RF Transmitter, shelf mount
(secondary, no software)
42321
Dual Digital Clock Wall Bracket (3x4/2.5x6/4x4)
42422
Dual Digital Clock Wall Bracket (4x6)
42443
Dual Analog & Digital Ceiling Bracket
42316
4in x 6 digit Digital Clock Chrome Wire Guard
42400
4in x 4 digit Digital Clock Chrome Wire Guard
42401
2.5in x 6 digit Digital Clock Chrome Wire Guard
42689
Digital Clock Wash-Down Enclosure
42247
Digital Security Mount Replacement
42281
Wall Clock Security Mount Replacement Key
Either part number required for clock synchronization.
3-YEAR LIMITED WARRANTY
Pyramid warranties its Synchronized Clock System to the original user against defective material or workmanship for
a period of 3 years from date of purchase.
The manufacturer’s responsibility under this Warranty is limited to repair or replacement of defective part or parts.
Pyramid reserves the right to determine whether parts failed because of defective material, workmanship, or other
causes. Failure caused by accident, alteration, misuse or improper packaging of returned unit is not covered by this
Warranty. Any repair to equipment other than by Pyramid voids the Warranty. Users in territories other than USA,
Canada, South America & Australia should contact the Dealer from whom the unit was purchased. The rights under
this Warranty are limited to original user and may not be transferred to subsequent users.
If Customer Support cannot troubleshoot your problem over the phone, we will replace your unit free of charge if it
is within warranty period. Please contact Customer Support at 888.479.7264 between the hours of 8am-5pmEST for
details.
Should you need to speak live to one our representatives, please call toll-free (US/Canada) at 888.479.7264 during
regular business hours: 8am-5pmEST, Monday-Friday.
I2255
Page 5 of 5
888.479.7264
pyramidtimesystem.com
ACCESSORIES
WARRANTY
TECHNICAL SUPPORT