qtran QOM-eLED Series User manual

QOM-eLED+DMX LED POWER SUPPLY 100W–300W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-25-20
COMPLIANT
Part Number Builder
QOM-eLED is Q-Tran's exterior rated surface mounted electronic
DMX power supply, utilizing a 100W constant voltage LED Driver
from Thomas Research and the LINEARdrive DMX decoder from
eldoLED. With the ability to fit up to 300W of power and control in
one enclosure, this unit provides plenty of flexibility and comes with
all decoders prewired together with terminal blocks for landing your
RGB or RGBW wires.
Technical Information
QOM-eLED UNV 24VDC DMX
Product Size1Prim. V Sec. V Control Opts2
100W
200W
300W
UNV 24VDC DMX BK
SS
1 Size
Size
Max Load
(Watts)
Secondary
Voltage
(12/24VDC)
Max Prim Amps
@ 120V
Max Prim Amps
@ 277V
100W 1x100W 24VDC 0.95A 0.40A
200W 2x100W 24VDC 1.90A 0.80A
300W 3x100W 24VDC 2.85A 1.20A
2 Options
BK Black Powder Coat Finish (Standard)
SS 316 Marine Grade Stainless Steel
Voltage Drop Chart
VDC Watts
(W)
10 AWG
(5.6mm²) 12 AWG (3.3mm²) 14 AWG (3.0mm²) 16 AWG (1.3mm²) 18 AWG (0.78mm²) 20 AWG (0.50mm²) 22 AWG (0.33mm²) 24 AWG (0.22mm²) 26 AWG (0.13mm²)
24
17
25
40
80
100
897'
567'
309'
130'
84'
564'
356'
194'
82'
53'
355'
224'
122'
51'
33'
223'
141'
77'
32'
21'
140'
88'
48'
20'
13'
88'
56'
30'
13'
8'
55'
35'
30'
8'
5'
35'
22'
12'
5'
3'
22'
14'
7'
3'
*Distances are based on a 5% Voltage drop max.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved

QOM-eLED+DMX LED POWER SUPPLY 100W–300W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-25-20
COMPLIANT
• Limited output voltage and current, plus isolation for safe operation
• Controllable with DMX decoder module
• Control 4 LED channels with DMX
• DMX dimming down to 0%
• Fully potted driver(s) for moisture resistance
• Suitable for dry, damp, and wet locations
• Suitable for use with submersible luminaire
• Surface mount only
• Primary voltage - universal (120-277V)
• Wide operating temperature range: -4˚F to 122˚F
• Fits up to (3):100W 24 VDC driver(s) and DMX decoder module(s)
• 5 years warranty
• Driver has Class A sound rating
• Class 2 output
• CSA #239924
Low Voltage Lighting Systems
: CSA Class 3425-15 and Class 3425-95
: CSA Standard C22.2 No. 250.0-08 - Luminaires
: ANSI/ UL Standard 2108 - Low Voltage Lighting System
: ANSI/ UL Standard 8750 - Light Emitting Diode (LED) Equipment for Use in Lighting Products
: CSA Std C22.2 No 250.13-14 - Light Emitting Diode (LED) Equipment for Lighting Applications
Landscape Lighting Systems
: CSA Class 3402-15 and Class 3402-95
: CSA Standard C22.2 No. 250.7-07 - Extra-Low-Voltage Landscape Lighting Systems
: ANSI/ UL Standard 1838 - Low Voltage Landscape Lighting Systems
: ANSI/ UL Standard 8750 - Light Emitting Diode (LED) Equipment for Use in Lighting Products
: CSA Std C22.2 No 250.13-14 - Light Emitting Diode (LED) Equipment for Lighting Applications
14.5"
15.4"
9.22"
BOTTOM TRAY
PRIMARYSECONDARY
LED DRIVER
(120V - 277V) (120V - 277V)
LED DRIVER
(120V - 277V)
LED DRIVER
(120V - 277V)
W B G R +24 W B G R +24 W B G R +24
DMX IN
NEU HOT GND
DMX OUT
A B C
A B C
BOTTOM
1.07"
1.36"
4.90"
M
-
+
M
-
+
M
-
+
TOP TRAY
5Knockouts of 1.07"
Hole for 3/4" fitting
4Knockouts of 1.36"
Hole for 1" fitting
A B C
Housing
• 18 gauge welded steel enclosure: 15.4"L x 9.22"W x 4.90"D
• Door: 14.5"L x 9.27"W
• Knockouts: 9
• Built-in support bracket incorporated to secure housing for
surface mounting
Performance
• Power Supply
: Rated for surface mount or outdoor use
: Fully rated to operate low voltage load at listed wattage
(No derating required)
: Voltage regulation to 2% or less of rated output voltage
: The ability to be dimmed using DMX dimming
: Universal input range of 120-277 Vrms
• Low Voltage Lighting Systems
: CSA Class 3425-15 and Class 3425-95
• LED Landscape Lighting System Components
: CSA Class 3402-15 and Class 3402-95
: Short circuit protection (SCP)
: Over voltage protection (OVP)
: Over current protection (OCP)
: Live tested by the manufacture to ensure proper
operation
: Manufacturer oers a minimum of 5 years warranty
• Terminal blocks is made of tin plated copper with a
voltage rating of 300V and a current rating of 40A

QOM-eLED+DMX LED POWER SUPPLY 100W–300W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-25-20
COMPLIANT
Specifications Protections
• Short Circuit Protection (SCP)
• Over Voltage Protection (OVP)
• Over Current Protection (OCP)
• Class 2 Output
Compliance
• EMI Spec : FCC 47 Part 15
: EN61000-3-2
• CSA Certified : UL-2108
: UL-1838
: UL-8750
: CSA C22.2 No 250.7-07
: CSA C22.2 No 250.0-08
: CSA C22.2 No 250.13-14
Input 24VDC
Input Voltage (Vrms) 120 230 277
Input Current, max (Arms) 0.98 0.51 0.43
Inrush Current, max*(Apk) --- 20 ---
Input Frequency (Hz) 50/60
Input Power (W) 177
Output RGB RGBW
Output Voltage, nom (V) 24 24
Output Current (A) 2.0 1.5
Output Power (Wmax) 100 100
Environmental Min Nom Max
THD (%) --- --- 20
PF (%) 0.90 --- ---
Case Temp (ºC) --- --- 90
*- 200us event
Efficiency / Load
50%
Load
Efficiency
66%
71%
76%
81%
86%
91%
96%
60% 70% 80% 90% 100%
120 Vac
240 Vac
23.4
23.5
23.6
23.7
23.8
23.9
24.0
24.1
24.2
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
Output Voltage (V)
Output Current (A)
Vout vs. Iout, 24VDC
277Vrms120Vrms

QOM-eLED+DMX LED POWER SUPPLY 100W–300W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-25-20
COMPLIANT
Wiring Diagram
12V - 28V DC IN
• To connect the driver to a DC power supply unit (PSU), connect the PSU’s positive voltage supply wire to the VDC+
connector and the PSU’s negative voltage supply wire to the VDC- connector.
EXT in
• You have the possibility to connect an external control device (0-10V control device, 10kΩ potentiometer or show selection
switch) to the driver’s Ext in+ and Ext in - connector. Configure the driver for use with an external control device over the 3 -
button user interface.
DMX in/LedSync out
• Use these connectors when the driver is used in a DMX network. For DMX in, connect the network cable’s DMX+, DMX-
and DMX shielding wire (the orange/white, orange and brown wire in a CAT5 cable) to the DMX in+, DMX in- and DMX in
shield connector respectively. For LedSync out, connect the network cable’s DMX+, DMX- and DMX shielding wire to the
LedSync out+, LedSync out- and LedSync shield connector respectively. DMX Shield must be grounded to Earth ground
at a single point external to power supply
LED groups
• Indicates the location of the connectors for your LED groups. R(ed) represents channel 1, G(reen) represents channel 2,
B(lue) represents channel 3 and W(hite) represents channel 4. The default group color allocation can be changed over the
3-button user interface.
M
Max | Vdc+
32V | Vdc-
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
TC
1
2
3
Group
Group
Group
Group
LED supply +
-
4
LINEARdrive 180D
12-28V / 6A Direct voltage controlled LED driver
LED groups
RR
WR BG
R
R
{
12-28VDC IN
-+2
1
0.2-1.5 mm2
0.35 inch
0.5-1.5 mm2
AWG 20-16
0.35 inch
AWG 24-16
VDC and LED connectors: Other connectors:
LedSync thru +
LedSync thru -
LedSync shield
DMX in +
DMX in -
DMX in shield
Ext in +
Ext in -

INSTALLATION LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Mounting Options
Housing
BOTTOM VIEW
ISOMETRIC VIEW
1.36" KNOCKOUT 4X
(FOR 1" FITTINGS)
1.07" KNOCKOUT 5X
(FOR 3/4" FITTINGS)
4.90"
14.5"
15.4"
9.22" 4.90"
NOTE: To order additional lengths of wire for connection in the secondary
Please call factory for availability.
: QOM must be installed as shown.
Pole Mount
Surface Wall Mount
2.00"
0.25"
1/4”x2” wood screw or
LAG bolt recommened
1.82"
3.38"
3.14"

INSTALLATION LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Connecting and Configuring the LINEARdrive 100D/180D
Primary Wiring
Secondary Wiring Control Wiring
DMX Connections
Commonly Asked Questions
1) How can I verify my installation?
• Apply AC input, verify display turns on : This confirms AC input wiring
• Run “Visual Test Run” : This verifies wiring of LEDs. Make sure LEDs turning on go in same order as the Test Run
2) I don’t have a controller yet, how can I keep my lights on?
• Change the Mode to “COLOR” : This allows to manually set a specific color to be on
• Adjust the Hue or WHITE to achieve the desired color : This sets that specific color
3) My LEDs aren’t coming out the right color. They look like white has been added in
• Verify the Network Resolution “NETW RES” : Default is 8 BT
• Check your DMX Programming. Stick controllers come with RGB programs by default. This will cause RGBW
LEDs to show Pink vs. Red
To DMX Controller
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
LINEARdrive 180D
-
12-28V / 6A Direct voltage controlled LED driver
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
LINEARdrive 180D
-
12-28V / 6A Direct voltage controlled LED driver
DMX in shield LedSync shield
DMX in - LedSync thyu -
DMX in + LedSync thyu +
Blue Wire = Blue LED
Red Wire = Red LED
Green Wire= Green LED
White Wire = White LED
Black Wire = +24V
A C
LED DRIVER 2
(120 - 277V)
B
M
-
+
GND
NEU
SECONDARY
PRIMARY
DMX Shield
DMX -
DMX +
-
+
iQ-LED
Blue = Blue White = White Green = Green Red = Red Black = +24V
W B G R +24
W B G R +24
DMXOUT
iQ-LED
M
-
+
DMX in + DMX in - DMX Shield LedSync thru + LedSync thru - LedSync Shield
DMXIN DMX OUT
HOT
NEU GND HOT
GND
HOT
NEU
LED DRIVER
(120 - 277V)
NEU GND HOT
DMXIN
GND
HOT
NEU
LED DRIVER
(120 - 277V)
NEU
GND
HOT
M
-
+
iQ-LED
TC
1
2
3
Group
Group
Group
Group
LED supply +
LINEARdrive 180D
4
Black Wire = +24V
Red Wire = Red LED
Green Wire = Green LED
Blue Wire = Blue LED
White Wire = White LED
iQ-LED
W B G R +24
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
-
DMX in shield
DMX in -
DMX in +
DMX
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed.
Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
● DMX Shield must be grounded to Earth Ground at a single point external to power supply

INSTALLATION LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Manual Configuration
Other Features
1. Select mode of operation: 2. Set LED groups:
3. Standalone Standalone Networked
operation or operation or operation
- Colour*- - Show - - DMX -
M
display off
SHOW
COLR
DMX
(5 sec)
M
+-
/
Set mode
MODE
SET
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
00...20
M
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...255
M
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
display off
ADDR
DMX
RES
NETW
M
+-
/
Interpolation
OFF
VID
COLR
WHIT
GLOW
INTERPOL
* The colour menu depends on the LED group settings you have selected in step 2.
Visual test run Locking the configuration: Reset to factory defaults
M
display off
TEST
-
+
Test
+ +
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
+ +
M
(5 sec)
Press menu
PRES MENU

INSTALLATION LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Wiring Installation
QOM-eLED+DMX
: for exterior
Blue Wire = Blue LED
Red Wire = Red LED
Green Wire = Green LED
White Wire = White LED
Black Wire = +24V
A C
LED DRIVER 2
(120 - 277V)
B
LED DRIVER 2
(120 - 277V)
B
LED DRIVER 2
(120 - 277V)
B
M
-
+
M
-
+
M
-
+
SECONDARY
PRIMARY
DMX Shield
DMX -
DMX +
M
-
+
LED
Blue = Blue White = White Green = Green Red = Red Black = +24V
W B G R +24V
NEU GND HOT
GND
HOT
NEU
A B C
W B G R +24 W B G R +24 W B G R +24
DMX INDMXOUT
A B C
LEDLED LED
GND
DMX +
DMX -
Red
Blue
Green
To next
power supply

INSTALLATION LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
CSA Requirements
• Suitable for indoor and outdoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and
the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
• DMX shield wire must be grounded to earth ground at a single point external to power supply.