qtran QTM-eLED+DALI-DT8 User manual

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply must be installed according to the National Electric
• Code and local codes and ordinances.
• This power supply is to be installed and serviced only by an licensed
electricians.
• This power supply is to be installed so that it is not likely to be contacted
by people.
• To avoid a hazard to children, account for all parts and destroy all
packaging materials.
• Do not install in wet locations.
LOW VOLTAGE LIGHTING SYSTEM
CLASS: 3425-15
3425-95
COMPLIANT
• Must be installed by licensed electrician.

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
HORIZONTAL VERTICAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stackedMore Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION
(Horizontal)
ROD SUSPENSION
(Vertical)
Double Sided
Key Hole
1/4" Rod Thru Hole
3/8" Rod Thru Hole
NOTE: Bracket can also be mounted (Top & Bottom)
for Vertical Mounts.
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
4.00"
BOTTOM VIEW
14.5"
8.00" 4.00"
ISOMETRIC VIEW
8.00"
Mounting Options
Housing

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes
must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
V-
V-
V+
V+
+
R-
G-
B-
W-
D1+
D2+
D1-
D2-
LED groups 12-36VDC IN
D2-
D1-
D2+
D1+
V+
V+
V-
V+
V-
B-
R-
G-
W-
LED groups 12-36VDC IN
DALI Signal
in/out
V-
V-
V+
V+
+
R-
G-
B-
W-
D1+
D2+
D1-
D2-
LED groups 12-36VDC IN
DALI Signal
in/out
DALI Signal
in/out
DALI
Controller
D1+
D2+
D1-
D2-
DALI
IN
DALI
OUT
V-
V-
V+
V+
+
R-
G-
B-
W-
12-36VDC INLED groups
LED
D1+
D2+
D1-
D2-
DALI Signal
in/out
V-
V-
V+
V+
+
R-
G-
B-
W-
12-36VDC INLED groups
LED
D1+
D2+
D1-
D2-
DALI Signal
in/out
V-
V-
V+
V+
+
R-
G-
B-
W-
12-36VDC INLED groups
LED
D1+
D2+
D1-
D2-
DALI Signal
in/out
Primary Wiring
Control Wiring: DALI Connections
Secondary Wiring
NEU
GND
HOT
LED DRIVER
(120-277V)
3-Wire default 4-Wire default 5-Wire default
To DALI Controller
V-
V-
V+
V+
+
R-
G-
B-
W-
D1+
D2+
D1-
D2-
D1+
D2+
D1-
D2-
{
12-36VDC IN
12-36VDC INLED groups
-+2
10.2-1.5 mm2
0.35 inch
0.5-1.5 mm2
AWG 20-16
0.35 inch
AWG 24-16
VDC and LED connectors: Other connectors:
DALI Signal
in/out
LED
V- V- V+ V+
+
R-
G-
B-
W-
D1+ D2+ D1- D2-
LED groups 12-36VDC IN
V- V- V+ V+
+
R-
G-
B-
W-
D1+ D2+ D1- D2-
LED groups 12-36VDC IN
DALI Signal
in/out
V- V- V+ V+
+
R-
G-
B-
W-
D1+ D2+ D1- D2-
LED groups 12-36VDC IN
DALI Signal
in/out
DALI Signal
in/out
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
*By others.
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
12-36VDC IN
+
R-
G-
B-
W-
LED groups
DALI
OUT
DALI
IN
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
Warm
Cool
+24V
+24V W C
D1+ D2+ D1- D2-
V- V- V+ V+
DALI Signal
in/out
12-36VDC IN
+
R-
G-
B-
W-
LED groups
DALI
OUT
DALI
IN
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
R G B+24
+24V
Red
Green
Blue
D1+ D2+ D1- D2-
V- V- V+ V+
DALI Signal
in/out
12-36VDC IN
+
R-
G-
B-
W-
LED groups
DALI
OUT
DALI
IN
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
R G B W+24
+24V
White
Red
Green
Blue
5-Wire4-Wire3-Wire
Connecting and Configuring the DALI-DT8 Decoder
NOTE:
For customization or pre-programming
contact a local sales rep.
DALI commissioning to be performed by a
third party at time of installation.

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
Other Features
1. Locking the configuration:
Confirm
1 2
Press and hold either button
(5 sec)
2. Reset to factory defaults:
Reset
1 2
1 2
Set Address
Press and hold either button
(5 sec)
Use the buttons to set address
DT8 Dimming Feature:
NOTE: DT8 color type of the dimmer can be TW, RGB, or RGBW.
Manual Configuration
0-6 0-9
1 2
Manual set button
Digital display
1. Set address manually:
(tens) (ones)
00~63
1 2
Press and hold either button
Use the buttons to set address
1 2
Set Address
(5 sec)
2. Set Output Type:
TW
RGB
RGBW
1 2
Press and hold both button
Use the second button to
set the output type
(5 sec)

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
C
LED DRIVER 2
(120 - 277V)
B
LED DRIVER 2
(120 - 277V)
LED DRIVER 2
B
V- V- V+ V+
+
D1+ D2+ D1- D2-
LED groups
DALI Signal
in/out
12-36VDC IN
R-
G-
B-
W-
V- V- V+ V+
+
D1+ D2+ D1- D2-
LED groups
DALI Signal
in/out
12-36VDC IN
R-
G-
B-
W-
V- V- V+ V+
+
D1+ D2+ D1- D2-
LED groups
DALI Signal
in/out
12-36VDC IN
R-
G-
B-
W-
NEU GND HOT
DALI
IN
DALI
OUT
LEAD WIRE
Black = +24V
White = White
Red = Red
Green = Green
Blue = Blue
NEU
GND
HOT
To next
power supply
R G B W +24 R G B W +24 R G B W +24
LEDLEDLED
DA +
DA -
Red
Blue
DALI
Controller
*By others.
DALI Bus
Power Supply
*By others.
SECONDARY
PRIMARY
DA -
DA +
NEU GND HOT
LED DRIVER
(120-277V)
D1+ D1- D2+ D2-
DALI IN DALI OUT
V- V- V+ V+
+
R-
G-
B-
W-
12-36VDC INLED groups
LED
D1+ D2+ D1- D2-
DALI Signal
in/out
Wiring Installation

INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8
© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-15-22
• Suitable for indoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in accordance with
applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION
PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET
SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.
LOW VOLTAGE
LIGHTING SYSTEM
Q-TRAN, INC.
MILFORD, CT U.S.A.
[phone]
WWW.Q-TRAN.COM
● Type Ic Recessed, Inherently Protected
Type IC ENCASTRE, PROTECTION INHÉRENTE
● For Supply Connections Use Wire Rated for At Least 60C.
Pour les connexions d'alimentation, utilisez des fils
calibrés pour au moins 60C.
● Suitable For Damp Locations
CONVIENT AUX EMPLACEMENTS HUMIDES
● Class 2
Classe 2
CLASS: 3425 - 95
3402 - 95
QTM-eLED-100+DALI
QTM-eLED-200+DALI
QTM-eLED-300+DALI
0.95 / 0.40
1.90 / 0.80
2.85 / 1.20
50/60
50/60
50/60
24
24
24
100
200
300
120 / 277
120 / 277
120 / 277
Model Input Voltage
(V)
Frequency Nominal Output
Voltage (VDC)
Nominal Output
Wattage (W)
Input Current
(A)
120V - 277V
INPUT VOLTAGE OUTPUT VOLTAGE
24V
CONTROL TYPE
DT8
DT6
6.00"
3.15"
QTM-eLED+DALI
QTM-eLED+DALI
C/US
CSA Requirements