qtran QTM-DRIVE User manual

QTM-DRIVE LED POWER SUPPLY 60W–200W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-19-20
Part Number Builder
QTM-DRIVE is an LED power supply for DMX or DALI control. It is
available in 12 or 24VDC and 60-200 watts of power. The QTM-DRIVE
utilizes eldoLED LINEARdrive drivers and is suitable for indoor use.
The power supplies and modules are all prewired together along
with terminal blocks for power and control wires. The housing can be
recessed or surface mounted.
QTM-DRIVE
Product Size1Sec. V Control Color2
60W
100W
120W
200W
12VDC
24VDC
DMX
DALI
WH (Standard)
BK
Technical Information
1 Size
Size
Max Load
(Watts)
Secondary
Voltage
(12/24VDC)
Max Prim Amps
@ 120V
Max Prim Amps
@ 277V
60W 1x60W 12VDC 0.60A 0.45A
120W 2x60W 12VDC 2.10A 0.90A
100W 1x100W 24VDC 1.05A 0.45A
200W 2x100W 24VDC 2.10A 0.90A
2 Color
WH White (Standard)
BK Black Powder Coat Finish
Voltage Drop Chart
VDC Watts
(W)
10 AWG
(5.6mm²) 12 AWG (3.3mm²) 14 AWG (3.0mm²) 16 AWG (1.3mm²) 18 AWG (0.78mm²) 20 AWG (0.50mm²) 22 AWG (0.33mm²) 24 AWG (0.22mm²) 26 AWG (0.13mm²)
12
12
25
60
315'
115'
7'
198'
72'
4'
125'
45'
3'
78'
28'
49'
18'
31'
11'
19'
7'
12'
4'
7'
4'
24
17
25
40
80
100
897'
567'
309'
130'
84'
564'
356'
194'
82'
53'
355'
224'
122'
51'
33'
223'
141'
77'
32'
21'
140'
88'
48'
20'
13'
88'
56'
30'
13'
8'
55'
35'
30'
8'
5'
35'
22'
12'
5'
3'
22'
14'
7'
3'
*Distances are based on a 5% Voltage drop max.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved

QTM-DRIVE LED POWER SUPPLY 60W–200W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-19-20
• DMX or DALI controllable
• Can fit up to 2 drivers
• Surface or recess mount capable
• 4x 12/24V controllable outputs per driver
• Standby power: < 0.5W
• Flicker free operation
• Built-in surge rotection: 3kV (L to N), 4kV (L/N to GND)
• Efficiency: 90% at full load, ≥ 87% above 50W output
• Power factor: > 0.94
• THD @ full load : <10%
• DMX dimming down to 0%
• 3 years warranty
• Class 2 output
• CSA #239924
Low Voltage Lighting Systems
: CSA class 3425-15 and class 3425-95
: CSA standard C22.2 No. 250.0-08 - Luminaires
: ANSI/ UL standard2108 - Low voltage lighting systems
: CSA standard C22.2 No 250.13-14 - Light emitting diode (LED) equipment for lighting
applications
: ANSI/ UL standard8750 - Light emitting diode (LED) equipment for use in lighting
products
Housing
• 18 gauge welded steel enclosure: 14.5"W x 8.00"H x 4.00"D
• Door: 15.5"W x 9.00"H
• Knockouts: 9
• Built-in support bracket incorporated to secure housing for surface mounting
Performance
• Power Supply
: Rated for surface mount or recessed use
: Fully rated to operate low voltage load at listed wattage (No derating required)
: Voltage regulation to 5% or less of rated output voltage
: Universal input range of 120-277 Vrms
• Low Voltage Lighting Systems
: CSA Class 3425-15 and Class 3425-95
: Short circuit protection (SCP)
: Overloadprotection (OLP)
: Live tested by the manufacture to ensure proper operation
: Manufacturer oers a minimum of 5 years warranty
• Terminal blocks is made of tin plated copper with a voltage rating of 300V and a current rating of 40A
14.5"
8.00"
PRIMARYSECONDARY
eldoLED
POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
eldoLED
POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
W B G R +24
A
W B G R +24
B
A B
DMX INDMXOUT
NEU
GND
HOT
BOTTOM
4.00"
9Knockouts of 0.875" Hole for 1/2" fitting
NOTE: 16 additional side knockouts

QTM-DRIVE LED POWER SUPPLY 60W–200W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-19-20
DMX in/LedSync out
• Use these connectors when the driver is used in a DMX network. For DMX in, connect the network cable’s DMX+, DMX-
and DMX shielding wire (the orange/white, orange and brown wire in a CAT5 cable) to the DMX in+, DMX in- and DMX in
shield connector respectively. ForLedSync out, connect the network cable’s DMX+, DMX- and DMX shielding wire to the
LedSync out+, LedSync out- and LedSync shield connector respectively.
DALI
• Use these connectors to connect the driver to a DALI network. Always combine a DA+ and DA- connector for either data
input or data output. A separate DALI power supply is required to power the DALI bus.
INPUT
• Voltage: 120 - 277 VAC, 50/60Hz
• Current, max per driver:
1.05A at 120V/60Hz
0.5A at 230V/50Hz
0.45A at 277V/60Hz
OUTPUT
• Power per driver: 100W max
• Voltage: 12V/24V output
• Current
RGBW @ 12V: 1.25A per output
RGBW @ 24V: 1A per output
• Output
RGB @ 12V: 1.66A per output
RGB @ 24V: 1.33A per output
• Current max: 5A common anode
ENVIRONMENTAL
• Ta operating range : -40°F ~ +122°F
• Tc max : 185°F
• Lifetime : 50K hours at 122°F
• MTBF : 480,000 hours
COMPLIANCE / SAFETY
• Class 2 output.
• Class A sound rating
• FCC: Title 47CFR Part 15 Class B
• The wiring inside electrical enclosures shall comply with the
600V/105 ºC or higher.
• CSA certified
: UL-2108
: UL-8750
: CSA C22.2 No 250.0-08
: CSA C22.2 No 250.13-14
NOTE: All measurements have been carried out at maximum load in free air without heat sink.
Wiring Diagram
Pay attention when connecting the LED groups:
•polarity reversal results in no light output and often damages
the LEDs
•combining + and -of different groups
damages the driver
2
1
9 mm
0.35 inch
0.5-1.5 mm 2
AWG 20-16
LED wire length: Maximum wire length
from LED driver to LED engine at full load:
AWG value 20 18 16
Distance (ft)
NOTE: Longer wire lengths increase EMI susceptibility.
M_+
120-277VAC
50-60Hz
DA -
+
DA -
+
~
~
1 2
DMX in shield
DMX in
-
DMX in +
LedSync out shield
LedSync out
-
LedSync out +
Ext in
-
Ext in +
+
-
+
-
DALI
{
N
LVAC
120-277
{
12V / 24V DIP switch
24V 12V
Non functional
RR
WR BG
R
R
Common anode
4 LED groups, 4 control channels
2
1
0.2-1.5 mm 2
9 mm
0.35 inch
AWG 24-16
46 72 118
NOTE

QTM-DRIVE LED POWER SUPPLY 60W–200W
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-11-19-20
Lifetime data
Life vs Ta
86
140
131
122
113
104
95
30
35
40
45
50
55
60
Ta
Life [kHours]
ºF
Power factor data
Power factor vs Vout at Ta 25 ºC / 77 ºF
0
60 50
40 30 20 10
0.70
0.75
0.80
0.85
0.90
0.95
1.00
1.05
Vout [V]
120V - 60Hz
230V - 50Hz
277V - 60Hz
Pf

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
HORIZONTAL VERTICAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stacked
More Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION
(Horizontal)
ROD SUSPENSION
(Vertical)
VERTICAL
Double Sided
Key Hole
1/4" Rod Thru Hole
3/8" Rod Thru Hole
NOTE: Bracket can also be mounted (Top & Bottom) for Vertical Mounts.
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
4.00"
BOTTOM VIEW
14.5"
8.00" 4.00"
ISOMETRIC VIEW
8.00"
Mounting Options
Housing

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Connecting and Configuring the LINEARdrive 100/S
Primary Wiring
Secondary Wiring Control Wiring
DMX Connections DALI Connections
Commonly Asked Questions
1) How can I verify my installation?
• Apply AC input, verify display turns on : This confirms AC input wiring
• Run “Visual Test Run” : This verifies wiring of LEDs. Make sure LEDs turning on go in same order as the Test Run
2) I don’t have a controller yet, how can I keep my lights on?
• Change the Mode to “COLOR” : This allows to manually set a specific color to be on
• Adjust the Hue or WHITE to achieve the desired color : This sets that specific color
3) My LEDs aren’t coming out the right color. They look like white has been added in
• Verify the Network Resolution “NETW RES” : Default is 8 BT
• Check your DMX Programming. Stick controllers come with RGB programs by default. This will cause RGBW
LEDs to show Pink vs. Red
eldoLED POWERdrive 100/S
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
eldoLED POWERdrive 100/S
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
A B
DMX Shield
DMX -
PRIMARY
SECONDARY
DMX +
DMX OUTDMX IN
_+
120-277VAC
50-60Hz
DA -
+
DA -
+
~ ~
1 2
LED
R G B W +24V
R G B W+24
A
R G B W+24
B
GND
HOT
NEU
LED LED
NEU GND HOT
GND
DMX +
DMX -
Red
Blue
Green
To next
power supply
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed.
Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
120-277VAC
50-60Hz
DA -
+
DA -
+
~
~
1 2
+
-
+
-
DALI
{
N
LVAC
120-277
{
12V / 24V DIP switch
24V 12V
Non functional
WR BG
Common anode RR
R
R
4 LED groups, 4 control channels
DMX in shield
DMX in
-
DMX in +
LedSync out
shield
LedSync out -
LedSync out +
Ext in
-
Ext in +
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
HOT GNDNEU
White = Neutral
Green = Ground
Black = Hot
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
M
-
+
LED
R G B W +24V
LED
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
DMX
DMX in shield
DMX in -
DMX in +
NOTE: The unit will be factory wired based on the way the unit is ordered.
Only the one applicable control will be prepared.
:DMX shielding wire must be grounded to Earth ground external to power supply.
DMX connections
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
DALI
+
_
+
_
DALI connections

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Manual Configuration
Other Features
Manual configuration
1. Select mode of operation:
M
display off
COLR
SHOW
DMX
DALI
(5 sec)
M
+-
/
Set mode
MODE
SET
2. Set LED groups:
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...510
M
Other features
Visual test run Locking the configuration: Reset to factory defaults
M
display off
TEST
-
+
Test
+ +
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
+ +
M
(5 sec)
Press menu
PRES MENU
*The colour menu depends on the LED group settings you have selected in step 2.
3. Standalone
operation
- Colour*-
or
00...20
display off
display off
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
Standalone
operation
- Show-
or
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
ADDR
DMX
RES
NETW
+-
/
DMX termination
YES
NO
M
Standalone
operation
- DMX or DALI-
Nr. of ballasts
No address Address set
or
OFF
VID
COLR
WHIT
GLOW
M
TERM X BAL
NO ADDR
ADDR SET
M
+-
/
Network resolution
AUTO
MANU
RES
NETW
M
+-
Network resolution
INTERPOL
M
M M
Manual configuration
1. Select mode of operation:
M
display off
COLR
SHOW
DMX
DALI
(5 sec)
M
+-
/
Set mode
MODE
SET
2. Set LED groups:
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...510
M
Other features
Visual test run Locking the configuration: Reset to factory defaults
M
display off
TEST
-
+
Test
+ +
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
+ +
M
(5 sec)
Press menu
PRES MENU
*The colour menu depends on the LED group settings you have selected in step 2.
3. Standalone
operation
- Colour*-
or
00...20
display off
display off
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
Standalone
operation
- Show-
or
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
ADDR
DMX
RES
NETW
+-
/
DMX termination
YES
NO
M
Standalone
operation
- DMX or DALI-
Nr. of ballasts
No address Address set
or
OFF
VID
COLR
WHIT
GLOW
M
TERM X BAL
NO ADDR
ADDR SET
M
+-
/
Network resolution
AUTO
MANU
RES
NETW
M
+-
Network resolution
INTERPOL
M
M M
Manual configuration
1. Select mode of operation:
M
display off
COLR
SHOW
DMX
DALI
(5 sec)
M
+-
/
Set mode
MODE
SET
2. Set LED groups:
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...510
M
Other features
Visual test run Locking the configuration: Reset to factory defaults
M
display off
TEST
-
+
Test
+ +
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
+ +
M
(5 sec)
Press menu
PRES MENU
*The colour menu depends on the LED group settings you have selected in step 2.
3. Standalone
operation
- Colour*-
or
00...20
display off
display off
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
Standalone
operation
- Show-
or
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
ADDR
DMX
RES
NETW
+-
/
DMX termination
YES
NO
M
Standalone
operation
- DMX or DALI-
Nr. of ballasts
No address Address set
or
OFF
VID
COLR
WHIT
GLOW
M
TERM X BAL
NO ADDR
ADDR SET
M
+-
/
Network resolution
AUTO
MANU
RES
NETW
M
+-
Network resolution
INTERPOL
M
M M

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
Wiring Installation
eldoLED POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
eldoLED POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
LED
R G B W +24V
R G B W+24
A
R G B W+24
B
DMX OUTDMX IN
GND
HOT
NEU
NEU GND HOT
A B
LED LED
GND
DMX +
DMX -
Red
Blue
Green
To next
power supply
: for interior
QTM-DRIVE
SECONDARY
PRIMARY
DMX Shield
DMX -
DMX +

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-09-29-20
CSA Requirements
• Suitable for indoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and
the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
• DMX shield wire must be grounded to earth ground at a single point external to power supply.
Model Input Voltage
(V)
Frequency Nominal Output
Voltage (VDC)
Nominal Output
Wattage (W)
Input Current
(A)
QTM-DRIVE-100
QTM-DRIVE-200
QTM-DRIVE
120/277
120/277
1.05
2.10
50/60
50/60
100
200
QTM-DRIVE-60
QTM-DRIVE-120
120/277
120/277
0.67
1.30
50/60
50/60
60
120
24
24
12
12
Q-Tran, Inc.
Q-TRAN, INC.
MILFORD, CT U.S.A.
[phone]
WWW.Q-TRAN.COM
CLASS: 3425 - 15
3425 - 95
120V-277V
INPUT VOLTAGE OUTPUT VOLTAGE
DMX
24V12V
DALI
LOW VOLTAGE
LIGHTING SYSTEM
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
CONTROL TYPE
● Type IC recessed, inherently protected
Type IC ENCASTRE, PROTECTION INHÉRENTE
● Wall mount only
INSTALLATION MURALE SEULEMENT
● Suitable for damp locations
CONVIENT AUX EMPLACEMENTS HUMIDES
● Not for use with dimmers
NE CONVIENT PAS À DES GRADATEURS
● For supply connections use wire rated
for at least 60ºC.
● Class 2
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION
PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET
SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.