qtran QTM-eLED+DALI-DT8-AN User manual

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply must be installed according to the National Electric
• Code and local codes and ordinances.
• This power supply is to be installed and serviced only by an licensed
electricians.
• This power supply is to be installed so that it is not likely to be contacted
by people.
• To avoid a hazard to children, account for all parts and destroy all
packaging materials.
• Do not install in wet locations.
LOW VOLTAGE LIGHTING SYSTEM
CLASS: 3425-15
3425-95
COMPLIANT
• Must be installed by licensed electrician.

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
AN-1 AN-2 AN-1 AN-2
14.5"
4.0"
8.0"
ISO VIEW
SURFACE MOUNTRECESSED MOUNT
Mounted in the secondary wiring compartment only
Conduit Entry Locations Lutron Athena Node
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
BOTTOM VIEW
4.0"
8.0"
16
ADDITIONAL
SIDE
KNOCKOUTS
14.5"
SIDE VIEW
4.0"
VERTICALHORIZONTAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stackedMore Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION (Vertical)
ROD SUSPENSION (Horizontal)
NOTE: Bracket can also be mounted
(Top & Bottom) for Vertical Mounts.
1/4" Rod Thru Hole
3/8" Rod Thru Hole
Double Sided
Key Hole
Athena nodes must be installed on the secondary side of power supply center and require 1.0” of clearance
in order to optimally function. Metal conduit must be 1.0” away from any node. Refer to the diagram above
for recommendations for conduit entry into secondary compartment.
Node And Conduit Entry Locations
Mounting Options

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes
must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
V-
V-
V+
V+
+
CW-
WW-
CW-
WW-
12-36VDC INLED groups
LED
D1+
D2+
D1-
D2-
DALI Signal
in/out
Primary Wiring Secondary Wiring
NEU
GND
HOT
LED DRIVER
(120-277V)
3-Wire default
Connecting and Configuring the DALI-DT8 Decoder
V-
V-
V+
V+
+
CW-
WW-
CW-
WW-
D1+
D2+
D1-
D2-
D1+
D2+
D1-
D2-
LED groups
DALI Signal
in/out
{
24VDC IN
-+
24VDC IN
LED
*Internal to QTM unit
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
+
CW-
WW-
CW-
WW-
LED groups
Warm
Cool
+24V
+24V W C
24VDC IN
DALI
IN
NEUHOT
3-Wire
NOTE:
For customization or pre-programming
contact a local sales rep.
DALI commissioning to be performed by a
third party at time of installation.

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
Other Features
1. Locking the configuration:
Confirm
1 2
Press and hold either button
(5 sec)
2. Reset to factory defaults:
Reset
1 2
1 2
Set Address
Press and hold either button
(5 sec)
Use the buttons to set address
DT8 Dimming Feature:
NOTE: DT8 color type of the dimmer with Lutron Athena Node can be TW only.
Manual Configuration
0-6 0-9
1 2
Manual set button
Digital display
1. Set address manually:
(tens) (ones)
00~63
1 2
Press and hold either button
Use the buttons to set address
1 2
Set Address
(5 sec)
2. Set Output Type:
TW
RGB
RGBW
1 2
Press and hold both button
Use the second button to
set the output type
(5 sec)

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
+
LED groups 24VDC IN
CW-
WW-
CW-
WW-
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
+
CW-
WW-
CW-
WW-
LED groups 24VDC IN
SECONDARY
PRIMARY
DA -
DA +
: for interior
*By others.
Warm
Cool
+24V
*By others.
Warm
Cool
+24V
+24V Cool− Warm− +24V Cool− Warm−
DALI IN
+ −
DALI IN
+ −
GND
HOT
NEU
NEU HOT GND
NEU GND HOT
LED DRIVER
(120-277V)
D1+ D1- D2+ D2-
DALI IN DALI IN
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
+
CW-
WW-
CW-
WW-
LED groups 24VDC IN
LED
DALI with Lutron Athena Node
QTM-eLED-200W+DALI-DT8-AN-2-3-3

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT8-AN
• Suitable for indoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in accordance with
applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
CSA Requirements