qtran QTM-eLED+DALI-DT6-AN User manual

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-15-23
COMPLIANT
QTM-eLED+DALI-DT6-AN
LED POWER SUPPLY 100W–200W
QTM-eLED UNV 24VDC2
Product Prim. V Sec. VControl2Color4 Size1Output Wiring 13Output Wiring 23
3Output Wiring
2-Wire Light Engines:
SW, SW-HE, SW-HE+, SD-SW, SC, WD
1 Size
Size Max Load
(Watts)
Secondary Voltage
(24VDC)
Max Prim Amps @
120V
Max Prim Amps @
277V
100W 1x100W 24VDC 0.95A 0.40A
200W 2x100W 24VDC 1.90A 0.80A
2Control: DALI-DT6-AN Lutron Athena Node
Total
Wattage
DALI-DT6-AN-1 DALI-DT6-AN-2
Node 1 Node 1 Node 2
100W 100W - -
200W 200W 100W 100W
3Output Wiring: 2-Wire Light Engines
SW, SW-HE, SW-HE+, SD-SW, SC, WD
4Color: WH White (Standard)
BK Black Powder Coat Finish
NOTE:
DALI-DT6-AN-1: 1 Lutron Athena Node. 1 zone of control for 100-200W. The entire output is controlled as a single zone.
DALI-DT6-AN-2: 2 Lutron Athena Nodes. 2 zones of control for 200W. Each of the two outputs are controlled as independent zones.
DALI-DT6-AN is 2-wire only.
The QTM-eLED+DALI-DT6-AN is a powerful LED power supply designed for DALI 2 applications.
It features the 100W constant voltage LED Driver from Thomas Research and DALI 2 DT-6 Decoders,
ensuring exceptional functionality and eciency. It also incorporates factory-installed Lutron Athena
Wireless Nodes, which streamlines installation time and allows for simple programming using the
Athena iOS or Android app. The power supplies and decoders are prewired together with terminal
blocks for easy installation of power and control wires. Combine Q-Tran lights and power with Athena
Wireless Nodes to create a complete Athena System to take your lighting to greater heights. Available
in 100-200 watt capacity, the QTM-eLED+DALI-DT6-AN can be recess or surface mounted.
See QTM-eLED+DALI-DT6 for power supply without Athena Nodes.
NOTE:
DALI-DT6-AN-1,2 is
the quantity of nodes
mounted in the QTM
enclosure. Multiple
Athena nodes allow for
multiple control zones in
one QTM enclosure.
NOTE:
2-Wire default is 1 address. For customization or pre-programming contact a local
sales rep. DALI commissioning to be performed by a third party at time of installation.
Part Number Builder
WH (Standard)
BK
100W N/A
200W 2
DALI-DT6-AN-1
DALI-DT6-AN-1
DALI-DT6-AN-2
Technical Information
Voltage Drop Chart
VDC Watts
(W) 10 AWG (5.6mm²) 12 AWG (3.3mm²) 14 AWG (3.0mm²) 16 AWG (1.3mm²) 18 AWG (0.78mm²) 20 AWG (0.50mm²) 22 AWG (0.33mm²) 24 AWG (0.22mm²) 26 AWG (0.13mm²)
24
17
25
40
80
100
897'
567'
309'
130'
84'
564'
356'
194'
82'
53'
355'
224'
122'
51'
33'
223'
141'
77'
32'
21'
140'
88'
48'
20'
13'
88'
56'
30'
13'
8'
55'
35'
30'
8'
5'
35'
22'
12'
5'
3'
22'
14'
7'
3'
*Distances are based on a 5% Voltage drop max.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-15-23
COMPLIANT
QTM-eLED+DALI-DT6-AN
LED POWER SUPPLY 100W–200W
• Limited output voltage and current, plus isolation for safe operation
• Controllable with Lutron Athena System for DALI 2 DT6 functionality
• DALI dimming down to 0.2%
• Fully potted driver(s) for moisture resistance
• Suitable for dry and damp locations
• Suitable for surface or recessed mounting use
• Primary voltage - universal (120-277V)
• Wide operating temperature range: -4˚F to 122˚F
• Fits up to (2):100W 24 VDC driver(s) and DALI decoder module(s)
• 5-year warranty
• Driver has Class A sound rating
• Class 2 output
• CSA #239924
Low Voltage Lighting Systems
: CSA class 3425-15 and class 3425-95
: CSA standard C22.2 No. 250.0-08 - Luminaires
: ANSI/ UL standard2108 - Low voltage lighting systems
: CSA standard C22.2 No 250.13-14 - Light emitting diode (LED) equipment for lighting
applications
: ANSI/ UL standard8750 - Light emitting diode (LED) equipment for use in lighting products
TOP TRAY
.875"
4.00"
BOTTOM
NOTE:
16 additional side knockouts
9 Knockouts of 0.875" Hole
for 1/2" fitting
V-
V-
V+
V+
+
12-36VDC INLED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
1(-)
2(-)
3(-)
4(-)
V-
V-
V+
V+
+
12-36VDC INLED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
1(-)
2(-)
3(-)
4(-)
V-
V-
V+
V+
+
1(-)
2(-)
3(-)
4(-)
12-36VDC INLED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
Housing
• 18 gauge welded steel enclosure: 14.5"W x 8.00"H x 4.00"D
• Door: 15.5"W x 9.00"H
• Knockouts: 25
• Built-in support bracket incorporated to secure housing for surface mounting
Performance
• Power Supply
: Rated for surface mount or recessed use
: Fully rated to operate low voltage load at listed wattage
(No derating required)
: Voltage regulation to 2% or less of rated output voltage
: The ability to be dimmed using DALI 2 DT-6 dimming
: Universal input range of 120-277 Vrms
• Low Voltage Lighting Systems
: CSA Class 3425-15 and Class 3425-95
: Short circuit protection (SCP)
: Over voltage protection (OVP)
: Over current protection (OCP)
: Live tested by the manufacturer to ensure proper operation
: Manufacturer oers a minimum of 5-year warranty
• Terminal blocks are made of tin plated copper with a voltage rating of 300V
and a current rating of 40A
Lutron Athena Node
• Compatibility with Lutron Athena System
• Enables wireless DALI 2 Device Type 6 control for
2-wire LED applications
• Each node controlled as a single zone, use multiple nodes to
create multiple zones
• Each Athena wireless node must be installed within 25' of
two or more Athena wireless nodes for robust Athena control
system connection
• Must be used as part of a Lutron Athena control System
14.5"
8.00"
DALI IN
+ −
DALI IN
+ −
NEU HOT GND
LED DRIVER
(120V - 277V)
LED DRIVER
(120V - 277V)
PRIMARYSECONDARY
TOP TRAY
V-
V-
V+
V+
D1+
D2+
D1-
D2-
DALI Signal
in/out
24VDC IN
+
1(-)
2(-)
3(-)
4(-)
LED groups
V-
V-
V+
V+
D1+
D2+
D1-
D2-
DALI Signal
in/out
24VDC IN
+
1(-)
2(-)
3(-)
4(-)
LED groups

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-15-23
COMPLIANT
QTM-eLED+DALI-DT6-AN
LED POWER SUPPLY 100W–200W
Protections
• Short Circuit Protection (SCP)
• Over Voltage Protection (OVP)
• Over Current Protection (OCP)
• Class 2 Output
Compliance
• EMI Spec : FCC 47 Part 15
: EN61000-3-2
• CSA Certified : UL-2108
: UL-8750
: CSA C22.2 No 250.0-08
: CSA C22.2 No 250.13-14
Input 24VDC
Input Voltage (Vrms) 120 230 277
Input Current, max (Arms) 0.98 0.51 0.43
Inrush Current, max*(Apk) --- 20 ---
Input Frequency (Hz) 50/60
Input Power (W) 117
Environmental Min Nom Max
THD (%) --- --- 20
PF (%) 0.90 --- ---
Case Temp (ºC) --- --- 90
*- 200us event
0
20
40
60
80
100
120
25 30 35 40 45 50 55 60 65 70 75 80 85 90
Life Time (kHrs)
Case Temperature (ºC)
Life Time vs. Case Temperature
Output Current (A)
120Vrms 277Vrms
23.4
23.5
23.6
23.7
23.8
23.9
24
24.1
24.2
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
Output Voltage (V)
Vout vs. Iout, 24VDC
20 40 60 80 100
% Rated Load
120Vrms 277Vrms
100
90
80
70
60
50
0
Efficiency (%)
Efficiency, 24VDC
Output SW DW
Output Voltage, nom (V) 24 24
Output Current (Amax)
per channel 4 4
Output Power (Wmax)
per decoder 100 100
Specifications (per 100W circuit)

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-15-23
COMPLIANT
QTM-eLED+DALI-DT6-AN
LED POWER SUPPLY 100W–200W
DALI Signal in/out
• Use these connectors when the driver is used in a DALI network. For DALI in, connect the network cable’s DALI+, to the D1+, and D1- connectors
respectively. For DALI out, connect the network cable’s DALI - to the D2+, and D2- connectors respectively.
• Lutron Athena control system required. By others.
LED groups
• Indicates the location of the connectors for your LED groups.The default group addressing can be changed over the 2-button user interface. For 2-wire
applications, 1(-) is wired to the - input on the terminal block.
Wiring Diagram
V-
V-
V+
V+
+
1(-)
2(-)
3(-)
4(-)
24VDC INLED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
D1+
D2+
D1-
D2-
{
24VDC IN
-+
LED
*Internal to QTM unit
NOTE:
2-Wire default is 1 address
For customization or pre-programming
contact a local sales rep.
DALI commissioning to be performed by
a third party at time of installation.
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
DALI
IN
24VDC IN
NEUHOT
-
+24V
-+
+
1(-)
2(-) 3(-)
4(-)
LED groups
2-Wire

© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-15-23
COMPLIANT
QTM-eLED+DALI-DT6-AN
LED POWER SUPPLY 100W–200W
AN-1 AN-2 AN-1 AN-2
14.5"
4.0"
8.0"
ISO VIEW
SURFACE MOUNTRECESSED MOUNT
Mounted in the secondary wiring compartment only
Conduit Entry Locations Lutron Athena Node
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
BOTTOM VIEW
4.0"
8.0"
16
ADDITIONAL
SIDE
KNOCKOUTS
14.5"
SIDE VIEW
4.0"
VERTICALHORIZONTAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stackedMore Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION (Vertical)
ROD SUSPENSION (Horizontal)
NOTE: Bracket can also be mounted
(Top & Bottom) for Vertical Mounts.
1/4" Rod Thru Hole
3/8" Rod Thru Hole
Double Sided
Key Hole
Athena nodes must be installed on the secondary side of power supply center and require 1.0” of clearance
in order to optimally function. Metal conduit must be 1.0” away from any node. Refer to the diagram above
for recommendations for conduit entry into secondary compartment.
Node And Conduit Entry Locations

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
LOW VOLTAGE LIGHTING SYSTEM
CLASS: 3425-15
3425-95
COMPLIANT
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply must be installed according to the National Electric
• Code and local codes and ordinances.
• This power supply is to be installed and serviced only by an licensed
electricians.
• This power supply is to be installed so that it is not likely to be contacted
by people.
• To avoid a hazard to children, account for all parts and destroy all
packaging materials.
• Do not install in wet locations.
• Must be installed by licensed electrician.

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
AN-1 AN-2 AN-1 AN-2
14.5"
4.0"
8.0"
ISO VIEW
SURFACE MOUNTRECESSED MOUNT
Mounted in the secondary wiring compartment only
Conduit Entry Locations Lutron Athena Node
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
BOTTOM VIEW
4.0"
8.0"
16
ADDITIONAL
SIDE
KNOCKOUTS
14.5"
SIDE VIEW
4.0"
VERTICALHORIZONTAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stackedMore Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION (Vertical)
ROD SUSPENSION (Horizontal)
NOTE: Bracket can also be mounted
(Top & Bottom) for Vertical Mounts.
1/4" Rod Thru Hole
3/8" Rod Thru Hole
Double Sided
Key Hole
Athena nodes must be installed on the secondary side of power supply center and require 1.0” of clearance
in order to optimally function. Metal conduit must be 1.0” away from any node. Refer to the diagram above
for recommendations for conduit entry into secondary compartment.
Node And Conduit Entry Locations
Mounting Options

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes
must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
V-
V-
V+
V+
+
1(-)
2(-)
3(-)
4(-)
24VDC INLED groups
LED
Primary Wiring Secondary Wiring
NEU
GND
HOT
LED DRIVER
(120-277V)
2-Wire default is 1 address
Connecting and Configuring the DALI-DT6 Decoder
V-
V-
V+
V+
+
1(-)
2(-)
3(-)
4(-)
24VDC INLED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
D1+
D2+
D1-
D2-
{
24VDC IN
-+
LED
*Internal to QTM unit
V- V- V+ V+
D1+ D2+ D1- D2-
DALI Signal
in/out
DALI
IN
24VDC IN
NEUHOT
-
+24V
-+
+
1(-)
2(-) 3(-)
4(-)
LED groups
2-Wire
NOTE:
2-Wire default is 1 address
For customization or pre-programming
contact a local sales rep.
DALI commissioning to be performed by
a third party at time of installation.

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
Other Features
0-6 0-9
1 2
Manual set button
Digital display
1. Set address manually:
(tens) (ones)
00~63
1 2
Press and hold either button
Use the buttons to set address
1 2
Set Address
(5 sec)
1. Locking the configuration:
Confirm
1 2
Press and hold either button
(5 sec)
2. Reset to factory defaults:
Reset
1 2
1 2
Set Address
Press and hold either button
(5 sec)
Use the buttons to set address
DT6 Dimming Feature:
NOTE: DT6 color type of the dimmer with Lutron Athena Node can be SW only.
Manual Configuration
2. Set LED groups:
Changing LED group
1A-SW
2A-TW
1 2
Press and hold both button
Use the first button to set the
amount of addresses
(5 sec)

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
V- V- V+ V+
+
1(-)
2(-) 3(-)
4(-)
24VDC INLED groups
D1+ D2+ D1- D2-
DALI Signal
in/out
V- V- V+ V+
+
24VDC INLED groups
D1+ D2+ D1- D2-
DALI Signal
in/out
1(-)
2(-) 3(-)
4(-)
OUTPUT LOAD
+ − + −
SECONDARY
PRIMARY
DA -
DA +
-
+24V
-
+24V
: for interior
GND
HOT
NEU
NEU HOT GND
DALI IN
+ −
DALI IN
+ −
DALI with Lutron Athena Node
D1+ D1- D2+ D2-
DALI IN DALI IN
NEU GND HOT
LED DRIVER
(120-277V)
V- V- V+ V+
+
1(-) 2(-) 3(-) 4(-)
24VDC INLED groups
LED
QTM-eLED-200W+DALI-DT6-AN-2-2-2

© 2021 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-13-23
INSTALLATION LED POWER SUPPLY - QTM-eLED+DALI-DT6-AN
• Suitable for indoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in accordance with
applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
CSA Requirements