qtran QTM-DRIVE User manual

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-17-21
HORIZONTAL VERTICAL RECESSED MOUNT
Plenum Door Required
Horizontal
Vertical
SURFACE SPACING SURFACE STACKING ROD SUSPENSION
9.5" O.C.
16" O.C.
19" O.C.
9.5" O.C.
9.5" O.C.
More Units can be stacked
More Units can be stacked
More Units can be stacked
NOTE: Rods not included.
RECESSED
SURFACE
ROD SUSPENSION
(Horizontal)
ROD SUSPENSION
(Vertical)
VERTICAL
Double Sided
Key Hole
1/4" Rod Thru Hole
3/8" Rod Thru Hole
NOTE: Bracket can also be mounted (Top & Bottom) for Vertical Mounts.
0.875" KNOCKOUT 9X
(FOR 1/2" FITTINGS)
4.00"
BOTTOM VIEW
14.5"
8.00" 4.00"
ISOMETRIC VIEW
8.00"
Mounting Options
Housing

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-17-21
Connecting and Configuring the LINEARdrive 100/S
Primary Wiring
Secondary Wiring Control Wiring
DMX Connections DALI Connections
Commonly Asked Questions
1) How can I verify my installation?
• Apply AC input, verify display turns on : This confirms AC input wiring
• Run “Visual Test Run” : This verifies wiring of LEDs. Make sure LEDs turning on go in same order as the Test Run
2) I don’t have a controller yet, how can I keep my lights on?
• Change the Mode to “COLOR” : This allows to manually set a specific color to be on
• Adjust the Hue or WHITE to achieve the desired color : This sets that specific color
3) My LEDs aren’t coming out the right color. They look like white has been added in
• Verify the Network Resolution “NETW RES” : Default is 8 BT
• Check your DMX Programming. Stick controllers come with RGB programs by default. This will cause RGBW
LEDs to show Pink vs. Red
eldoLED POWERdrive 100/S
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
eldoLED POWERdrive 100/S
M_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
A B
DMX Shield
DMX -
PRIMARY
SECONDARY
DMX +
DA -
+
DA -
+
~ ~
1 2
LED
R G B W +24V
R G B W+24
A
R G B W +24
B
GND
HOT
NEU
LED LED
NEU GND HOT
GND
DMX +
DMX -
Red
Blue
Green
To next
power supply
DMX OUTDMX IN
WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed.
Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
120-277VAC
50-60Hz
DA -
+
DA -
+
~
~
1 2
+
-
+
-
DALI
{
N
LVAC
120-277
{
12V / 24V DIP switch
24V 12V
Non functional
WR BG
Common anode RR
R
R
4 LED groups, 4 control channels
DMX in shield
DMX in
-
DMX in +
LedSync out
shield
LedSync out -
LedSync out +
Ext in
-
Ext in +
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
HOT GNDNEU
White = Neutral
Green = Ground
Black = Hot
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
-
+
LED
R G B W +24V
LED
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
DMX
DMX in shield
DMX in -
DMX in +
NOTE: The unit will be factory wired based on the way the unit is ordered.
Only the one applicable control will be prepared.
:DMX shielding wire must be grounded to Earth ground external to power supply.
DMX connections
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~
~
1 2
DALI
+
_
+
_

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-17-21
Manual Configuration
Other Features
1. Select mode of operation:
M
display off
COLR
SHOW
DMX
DALI
(5 sec)
M
+-
/
Set mode
MODE
SET
2. Set LED groups:
RGB
RGBW
RGBA
RRGB
RGGB
CCWW
CWWW
1-1L
2-2L
3-3L
4-4L
2-4L
1-4L
M
M
+
+-
/
LED groups
LED
+
OFF
POTM
10V
SWIT
display off
M
+-
/
External input
EXT INP
+-
/
LOG
LIN
Dimming curve
M
DIM CURV
HUE
M
HUE
White
WHIT
M
M
+-
/
Intensity
0...255
INT
display off
+-
/
0...1535
+-
/
0...510
M
*The colour menu depends on the LED group settings you have selected in step 2.
3. Standalone
operation
- Colour*-
or
00...20
display off
display off
display off
SHOW
M
M
M
-99...99
0...255
+-
/
+-
/
+-
/
Intensity
Speed
Show
SPD
INT
M
Standalone
operation
- Show-
or
M
M
+-
/
+-
/
1...512
Network resolution
DMX address
8 BT
16 BT
ADDR
DMX
RES
NETW
+-
/
DMX termination
YES
NO
M
Standalone
operation
- DMX or DALI-
Nr. of ballasts
No address Address set
or
OFF
VID
COLR
WHIT
GLOW
M
TERM X BAL
NO ADDR
ADDR SET
M
+-
/
Network resolution
AUTO
MANU
RES
NETW
M
+-
Network resolution
INTERPOL
M
M M
Visual test run Locking the configuration: Reset to factory defaults
M
display off
TEST
-
+
Test
+ +
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
R 1 sec
G 1 sec
B 1 sec
W 1 sec
RGBW 1 sec
+-
/
display off
M
LOCK
M
+
Lock driver
+(5 sec)
NO
SOFT
HARD
M
display off
RE - SET
-
+
Reset
+ +
M
(5 sec)
Press menu
PRES MENU

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-17-21
Wiring Installation
eldoLED POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
eldoLED POWERdrive 100/S
M
_+
120-277VAC
50-60Hz
DA
-
+
DA
-
+
~ ~
1 2
Red = Red
Green = Green
Blue = Blue
White = White
Black = +24V
DA
-
+
DA
-
+
~ ~
1 2
LED
R G B W +24V
R G B W+24
A
R G B W+24
B
GND
HOT
NEU
NEU GND HOT
A B
LED LED
GND
DMX +
DMX -
Red
Blue
Green
To next
power supply
: for interior
QTM-DRIVE
SECONDARY
PRIMARY
DMX Shield
DMX -
DMX +
DMX OUTDMX IN

INSTALLATION LED POWER SUPPLY - QTM-DRIVE
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-06-17-21
CSA Requirements
• Suitable for indoor use
• This power supply must be installed according to the National Electric Code and local codes and ordinances and in
accordance with applicable installation code by a person familiar with the construction and operation of the product and
the hazards involved.
• Wear rubber shoes and work on a sturdy wooden or fiberglass ladder.
• This power supply is to be installed in a location where it is not likely to be contacted by non-electricians.
• To avoid a hazard to children, account for all parts and destroy all packaging materials.
• DMX shield wire must be grounded to earth ground at a single point external to power supply.
Model Input Voltage
(V)
Frequency Nominal Output
Voltage (VDC)
Nominal Output
Wattage (W)
Input Current
(A)
QTM-DRIVE-100
QTM-DRIVE-200
QTM-DRIVE
120/277
120/277
1.05
2.10
50/60
50/60
100
200
QTM-DRIVE-60
QTM-DRIVE-120
120/277
120/277
0.67
1.30
50/60
50/60
60
120
24
24
12
12
Q-Tran, Inc.
Q-TRAN, INC.
MILFORD, CT U.S.A.
[phone]
WWW.Q-TRAN.COM
CLASS: 3425 - 15
3425 - 95
120V-277V
INPUT VOLTAGE OUTPUT VOLTAGE
DMX
24V12V
DALI
LOW VOLTAGE
LIGHTING SYSTEM
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and
operation of the product and the hazards involved.
CONTROL TYPE
● Type IC recessed, inherently protected
Type IC ENCASTRE, PROTECTION INHÉRENTE
● Wall mount only
INSTALLATION MURALE SEULEMENT
● Suitable for damp locations
CONVIENT AUX EMPLACEMENTS HUMIDES
● Not for use with dimmers
NE CONVIENT PAS À DES GRADATEURS
● For supply connections use wire rated
for at least 60ºC.
● Class 2
CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D'INSTALLATION
PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET
SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS.