Qtx HPWash 100 User manual

www.avsl.com 154.050UK User Manual
HPWash 100
High Power Stage Blinder
Item ref: 154.050UK
User Manual
Thank you for choosing the HPWash100, a powerful 100W white LED stage-blinder for a fully
controllable light wash to stage or audience. Linear dimming control via DMX or internal
programs can provide a smooth or immediate transition from blackout to full brightness.
Housed in an all-metal casing with fan cooling for durability and reliable operation.
In the box:
Your HPWash 100 should arrive with you in a single carton in good condition. The carton
should contain 1 x main unit with bracket, 1 x UK IEC mains lead and 1 x manual.
Warning:
To prevent risk of fire or electric shock, do not expose the unit to rain or damp environments.
In the event of a spillage, disconnect the mains and allow the unit to dry out naturally.
Qualified personnel should then check the unit before continuing use.
Please read through this manual thoroughly before use, any damage
Caused by misuse of product will not be covered by warranty.
Please do not open cover, contains high voltage. This
product is not serviceable or repairable by the end user.
Please refer to qualified personnel for service and repair.

www.avsl.com 154.050UK User Manual
Placement:
•Use the included mounting bracket to fix to a stand or lighting truss
•Use secondary safety fixings if mounting overhead.
•Keep away from damp or dusty environments
•Ensure adequate air-flow around the fixture housings
•Ensure adequate access to controls and connections
Cleaning:
•Use a soft cloth with a neutral detergent to clean the casing as required
•Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups
•Do not use strong solvents for cleaning the unit
Rear panel controls:
1. IEC mains in
2. Earth screw (DO NOT REMOVE)
3. LCD display
4. Manual control buttons
5. DMX Signal in
6. DMX Signal out
Manual control menu:
Press the “MENU” button to enter the settings menu.
Press “UP” and “DOWN”buttons to navigate through various setting functions.
Press “ENTER” button to confirm the desired setting.
1.
2.
3.
4.
5.
6.

www.avsl.com 154.050UK User Manual
Menu
Function
Description
d0xx
d001-d512
DMX address settings
Auxx
Au01-Au03
Auto master modes left, right and both lamps
Au04-Au05
Auto master colour jump and scroll
So01
Sound activated colour jump constant
So02
Sound activated colour jump strobe
Stxx
St00
Auto master constant (Au01-Au05)
St01-St16
Auto master strobe from slow to fast (Au01-Au05)
Snxx
Sn01 - Sn16
Sound activation speed adjust from slow to fast (So01 &
So02)
Spxx
Sp01-Sp16
Auto master speed control (Au04 & Au05)
U0xx
u001-u255
White max brightness set low to high
DMX mode:
The HPWash 100 can be controlled by DMX signal, simply connect the DMX signal source to
the DMX input on the unit via a balanced XLR lead. Extra fixtures can be controlled by the
same DMX signal by looping through the DMX out on the unit. To enter DMX mode, select
D001 from the menu and confirm the correct start address by using the “UP”and “DOWN”
buttons and “ENTER”to confirm.
This unit has 6 DMX channels as indicated in the table below:
Channel
Channel address
Function
CH1
0-255
Master dimmer –low to high
CH2
1-255
Strobe –Slow to fast
CH3
1-255
Macro effects selection
CH4
0-255
Macro effects speed adjust –slow to fast
CH5
0-255
Right lamp white dimmer –low to high
CH6
0-255
Left lamp white dimmer –low to high
Specifications:
Power supply
110-240Vac, 50/60Hz (IEC)
Power consumption
100W
Fuse rating
F2AL, 250Vac
Light source
2x 50W White LED
DMX channels
6
Beam angle
40°
Housing
Full Metal, powder painted.
Dimensions
270x135x125mm (Without bracket)
Weight
1.52kg

www.avsl.com 154.050UK User Manual
Troubleshooting:
No power
(mains)
Check mains voltage is correct and outlet is switched on
Check IEC lead and fuse (if fuse continually blows, refer to
your dealer)
No light output
Check control panel mode settings
Check DMX settings from controller (dimmer levels, blackout
etc.)
No strobe
output
Check strobe settings on control panel or from DMX controller
Unresponsive
to DMX
Check that unit is in DMX mode and ensure DMX address
remains lit to confirm receiving DMX signal
Check DMX controller is not set to black out
Check DMX controller is on correct fixture/page
Check master dimmer value
Check correct DMX address is set
Check DMX connection and leads
Overheating/
cutting out
Ensure adequate ventilation and unit is not too close to a heat
source
This product is classed as Electrical or Electronic equipment and should not be disposed
with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2021 AVSL Group Ltd, Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point House,
Taylor Road, Trafford Park, Manchester. M41 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland.