Qtx Tri-Bar User manual

www.avsl.com 151.593UK User Manual
Tri-Bar
3 Segment RGB LED Wall Bar
Item ref: 151.593UK
User Manual
Thank you for choosing the QTX Tri-Bar with 18 high output RGB LEDs to provide colour washes and
moving patterns against walls, ceilings or even floors. The 3 groups of 6 LEDs can be controlled by auto or
sound activated modes from preset internal colour sequences. Alternatively, the bar can be operated
remotely by DMX in either 3, 7 or 13 channel modes and connected to more units if a larger effect is
needed.
In the box:
Your Tri-Bar should arrive with you in a single carton in good condition. The carton should contain
1 x main unit, 2 fixing stand/brackets with thumbscrews, 1 x UK IEC mains lead and 1 x manual.
Warning:
To prevent risk of fire or electric shock, do not expose the unit to rain or damp environments. In the event
of a spillage, disconnect the mains and allow the unit to dry out naturally. Qualified personnel should then
check the unit before continuing use.
Please read through this manual thoroughly before use, any damage
caused by misuse of product will not be covered by warranty.
Please do not open cover, contains high voltage. This
product is not serviceable or repairable by the end user.
Please refer to qualified personnel for service and repair.

www.avsl.com 151.593UK User Manual
Placement:
•Use the included mounting brackets to fix to a stand or lighting truss.
•Use secondary safety fixings if mounting overhead.
•Keep away from damp or dusty environments.
•Ensure adequate airflow around the fixture housings.
•Ensure adequate access to controls and connections.
•Do not aim LED or laser output directly into line of sight, as this can result in eye injury.
Cleaning:
•Use a soft cloth with a neutral detergent to clean the casing as required.
•Do not use strong solvents for cleaning the unit.
Side panel controls:
Manual control menu:
Press the “MENU” button to enter the settings menu.
Press “UP” and “DOWN” buttons to navigate through various setting functions.
Press “ENTER” button to confirm the desired setting.
Menu
Function
Description
d001
d001 - d512
DMX address settings
CH3/CH7/CH13
DMX channel selection
Au
Au00 - Au16
Automatic modes
FL
FL00 - FL09
Automatic mode strobe –slow to fast
SP
SP00 - SP09
Automatic mode speed –slow to fast
So
So01 - So02
Sound activated modes
Sn
Sn01 - Sn09
Sound activated mode sensitivity adjustment –low to high
DMX mode:
The Tri-Bar can be controlled by DMX signal, simply connect the DMX signal source to the DMX input on
the unit via a balanced XLR lead. Extra fixtures can be controlled by the same DMX signal by looping
through the DMX out on the unit. To enter DMX mode, select d001 from the menu and confirm the correct
start address and channel selection by using the “UP”and “DOWN”buttons and “ENTER”. The “d”on
the LED display will begin to flash once it’s received the DMX signal from the controller. This unit has 3, 7
or 13 DMX channels as indicated in the table below:

www.avsl.com 151.593UK User Manual
3 Channel mode:
Channel
Value
Function and description
1
0 - 255
Red dimmer (0-100%)
2
0 - 255
Green dimmer (0-100%)
3
0 - 255
Blue dimmer (0-100%)
7 Channel mode:
Channel
Value
Function and description
1
0 - 255
Master dimmer (0-100%)
2
0 - 255
Red dimmer (0-100%)
3
0 - 255
Green dimmer (0-100%)
4
0 - 255
Blue dimmer (0-100%)
5
0 - 255
Strobe (slow to fast)
6
0 - 009
Manual dimming
10 - 249
Integrated effects
250 - 255
Sound to light
7
0 - 255
Speed adjust (slow to fast)
13 Channel mode:
Channel
Value
Function and description
1
0 - 255
Segment 1 red dimmer (0-100%)
2
0 - 255
Segment 1 blue dimmer (0-100%)
3
0 - 255
Segment 1 green dimmer (0-100%)
4
0 - 255
Segment 2 red dimmer (0-100%)
5
0 - 255
Segment 2 blue dimmer (0-100%)
6
0 - 255
Segment 2 green dimmer (0-100%)
7
0 - 255
Segment 3 red dimmer (0-100%)
8
0 - 255
Segment 3 blue dimmer (0-100%)
9
0 - 255
Segment 3 green dimmer (0-100%)
10
0 - 255
No function
11
0 - 255
Strobe (slow to fast)
12
0 - 009
Manual dimming
10 - 249
Integrated effects
250 - 255
Sound to light
13
0 - 255
Blue dimmer (0-100%)
Specifications:
Power supply
110-240Vac, 50/60Hz (IEC)
Power consumption
60W
Fuse rating
F3A
LED type
18x 3W RGB 3-in-1 COB
Beam angle
45°
Modes
Static colour, colour change, colour fade, auto, sound active,
DMX, master/slave
DMX channels
3, 7 or 13
Dimensions
1150 x 60 x 60mm
Weight
1.850kg

www.avsl.com 151.593UK User Manual
Troubleshooting:
No power (mains)
Check mains voltage is correct and outlet is switched on
Check IEC lead and fuse (if fuse continually blows, refer to your dealer)
No light output
Check control panel mode settings
Check DMX settings from controller (dimmer levels, blackout etc.)
Unresponsive to DMX
Check that unit is in DMX mode and ensure the A on the DMX address flashes
to confirm it’s receiving a DMX signal
Check DMX controller is not set to black out
Check DMX controller is on correct fixture/page
Check master dimmer value
Check correct DMX address is set
Check DMX connection and leads
Overheating/
cutting out
Ensure adequate ventilation and unit is not too close to a heat source
This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste
at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2022 AVSL Group Ltd, Unit 2 Bridgewater Park, AVSL (Europe) Ltd, Unit 3D North Point House,
Taylor Road, Trafford Park, Manchester. M41 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland.