Quadratec QuadraTop 11113.2435 User manual

QuadraTop®Complete Soft Top
for 2018- Current
4 Door Jeep®Wrangler JLU
Item #11113.2435
Loss of vehicle control involves risk of death or serious injury, particularly to
parts of your body not restrained within vehicle. This product is intended for
weather protection only and should not be relied upon to contain occupants
in the event of an accident or to protect from either ground contact or falling
objects. To reduce risk of accident or injury:
•ALWAYS WEAR SEATBELTS
• Always keep head, arms & body parts within vehicle.
• Fully secure or stow the soft top before driving according to instructions.
Never try to latch or fold soft top while driving. Do not use if damaged or
worn.
• Read and follow all instructions & warnings accompanying this product, in
your vehicle owner’s manual and O󰀨 Road Driving Supplement.
RISK OF EYE INJURY. Safety glasses should be worn at all times while install-
ing or maintaining this product.
PART LIST:
TOP DECK/HEADER AND REAR BOWS ASSEMBLY QTY 1
DRIVER SIDE QUARTER WINDOW QTY 1
PASSENGER SIDE QUARTER WINDOW QTY 1
REAR WINDOW QTY 1
CENTER BOW ASSEMBLY QTY 1
DRIVER SIDE DOOR SURROUND QTY 1
PASSENGER SIDE DOOR SURROUND QTY 1
DOOR SURROUND RUBBER QTY 2
DOOR SURRUND SCREWS QTY 1
REQUIRED TOOLS:
SAFETY GLASSES
SOCKET WRENCH
10MM SOCKET & DRIVER
PHILLIPS HEAD SCREW DRIVER
This Replacement Top kit is designed to t on your 4 Dr Jeep® Wrangler when
the original soft top or hard top has been completely removed. Before begin-
ning your installation of this product, you will need to remove your existing soft
top fabric, hardware or Hard top.
WARNING
CAUTION
NOTICE
DOOR SURROND KNOBS QTY 8
TAILGATE BAR QTY 2
TAILGATE BAR CORNER MOUNTS QTY 4
CORNER MOUNTS SHORT KNOBS QTY 8
REAR BOW SCREWS AND NUTS QTY 4
REAR BRACKET SCREWS & NUTS QTY 2
REAR MAIN BRACKET SCREWS AND NUTS QTY 2
4MM ALLEN WRENCH QTY 1
REAR MAIN BRACKET SCREW M8 QTY 4
5MM ALLEN WRENCH QTY 1

Important Safety information
Your QuadraTop® Complete Soft Top is
intended to be used with other Quadra-
Top Products to increase the fair weath-
er enjoyment of your o-road capable
vehicle. Before installation,
please take a moment to review the
following safety information and installa-
tion instructions. Important safety infor-
mation is generally preceded by one of
three signal words indicating the relative
risk of injury.
The signal words mean.
a hazardous situation which, if not avoided, could result in death or serious in-
jury. You CAN be KILLED or SERIOUSLY HURT if you don’t follow instructions.
WARNING
CAUTION
NOTICE
a hazardous situation which, if not avoided, could result in minor or moderate
injury. You CAN be moderately HURT and also may su󰀨er property damage if
you don’t follow instructions.
Careful attention is required to this instruction or operation but does general-
ly not relate to personal injury. Damage to your Quadratec® product or other
property may result if you don’t follow instructions.
Before you begin Installation:
We are excited that you have chosen
the QuadraTop Complete Soft Top. This
high-quality soft top is designed to pro-
vide protection from the elements and a
stylish look on your Jeep®.
For a smooth t and ease of installation, this top should be installed at tem-
peratures above 72 degrees. Below this temperature, the fabric may contract an
inch or more making it di󰀩cult to install. We highly recommend taking the top
out of the package and letting it sit inside a warm place or direct sunlight for
1-2 hours before you install the top. When warm, this top will install quickly.
NOTICE
2
Put your safety Glasses. Carefully
remove the contents of each box orga-
nizing them as shown in Fig.1 making
sure the passenger side and driver’s
side components are separated.
FIG 1
Passenger Side Door Surround
Driver Side Door Surround
Knobs 4mm Allen Wrench
Step 1: Un-packing & Organizing the Door Surrounds:
Put on safety glasses. Carefully remove all the contents of the large shipping box
onto a table top or onto the grown on top of a soft towel.
Once the components are removed
from the shipping box, locate the front
and rear door surround components and
accessories as shown in FIG1.
When unpacking, carefully check to
make sure all parts are included. If any
part is missing or broken, please call
Quadratec customer service at 800-745-
6037. Please note that it is important
that you become familiar with the instal-
lation process of this top by reading the
following instruction sheet and warnings
thoroughly.

3
FIG 2
Passenger Front door surround
Driver Front door surround
FIG 3
Step 2: Secure Front Door Sur-
rounds to the Roll Bar
Locate the set of screw knobs and
the driver’s side front door surrounds
(Fig 2). There should be 2 sets of
four knobs. See g 1. These knobs
go on the front and rear holes of
the brackets.
Line up the front driver’s side door
surround bracket holes with the
vertical holes in the over door
horizontal roll bar. Slip the front two
knobs through the brackets holes in
the front door surround (FIG. 3)
lining it up with the hole in the top of
the surround bracket on top of the front
horizontal roll bar. If you use a rolling
motion while you push the brackets,
it will be easier to install. Repeat on
the passenger side of the vehicle (See
note to the right). Loosely tighten each
of the knobs securing the front door
surround.
Step 3: Rear Over Door Surround
Assembly
Locate the driver’s side rear over
door assembly, the driver’s side
Pillar assembly, the Rubber seal
and the 4mm Allen head wrench (Fig
5).On the driver’s side rear over door
assembly, there are two screws
installed for shipping (Fig 6). Remove
these screws and set aside. Place the
rubber seal on the driver’s side pillar
assembly (Fig 6A) Line up the Driver
side pillar assembly and the driver side
rear over door assembly as shown in
fig 7. Insert the screws and tighten
using the included 4mm Allen wrench
securing the two pieces (fig 8)
Note: if you have difficult lining up the top of the
knobs with the upper bracket hole, you can
remove the installed top brackets covering the top
hole to get a better view of how the screw lines up.
FIG 5
Passenger
side Pillar
Assembly
Driver
side Pillar
Assembly
4mm Allen
Wrench
Driver side Rear Over-Door
Assembly
Passenger side Rear Over-Door
Assembly
FIG 6
FIG 8
FIG 7
Rubber
Seal
FIG 6A

4
FIG 9
FIG 10
FIG 11 FIG 12
Line up the rear door surround
bracket holes with the vertical holes
in the rear horizontal roll bar. If you
use a rolling motion while you push the
brackets on it will be easier to install.
Slip the two knobs through the
brackets holes in the rear door
surround (as you did in step 3).
Loosely tighten the knob securing the
rear door surround.
FIG 13
FIG 13A
Note: if you have dicult lining up the
top of the knobs with the upper brack-
et hole, rotate the bottom of the door
surround pin out of the body tub slightly
towards you and start the knob. Rotate
the pins back into the tub and tighten
knob. You can also remove the installed
top brackets covering the top hole to get
a better view of how the screw lines up.
See Fig 14a & 14b.
Step 4: Attaching the corner mounts
Step 4: Install & Secure Rear Door
Surrounds to the Roll Bar
Locate the assembled Driver’s side
rear door surround previously in-
stalled in step 3.(Fig 9) and a set of
screw knobs.
On the bottom of the vertical pillar
portion of the assembled door surround
are two pins as shown in FIG 10 that
will be inserted into the body tub. Insert
this pin into the body tub as shown in
FIG’s 11 & 12. Repeat this procedure
on the passenger side rear door sur-
round.
Line up the rear end of the front door
surround with the front of the rear door
surround as shown in fig 13. Make sure
the rear door surround seals are on top
of the front Door Surrounds as shown
in Fig 13A.
FIG 14a FIG 14b
FIG 15
FIG 16
Locate the corner mounts and two
short knobs (FIG 15). Locate the driv-
er’s side corner mount and line up with
the corner of the body tub. With the
short knob, secure the corner mount to
the body tube and tighten. See Fig’s 16
& 17
FIG 17

5
Step 5: Installing the Center Bow #1
& #2
Locate the center bow #1 (Fig 18).
Each Bow has been labeled to make
identication easier. Loosen the
screws holding on the top brackets.
With the help of a friend, place the
Quick release end on the bottom of
the bow leg over the second vertical
bracket (Fig 19). Pull the quick
release knob out and push the bow
down mounting the quick release to
the bracket. The quick release knob
is spring loaded so you should here a
“click” when it is secure in the bracket
(FIG 19a). Once the bow is installed,
tighten the bow mount bracket on the
door surround (Fig 20).
Repeat this bow mounting on the other
side of the vehicle and then repeat
the above procedure with center bow
#2 (FIG 21). Tighten down the door
surround knobs on each side of the
vehicle securing the Door surrounds
and the two bows.
FIG 18
Center Bow #1
Center Bow #2
FIG 19
4mm Allen
Wrench
Center Bow #1
FIG 20
FIG 19a
Center Bow #2
FIG 21
FIG 21a
Center Bow #2
4mm Allen
Wrench
FIG 22
Driver side rear
main bracket.
Passenger side rear
main bracket.
FIG 23 FIG 24
FIG 25
Step 7: Installing the rear main
bracket to the vehicle
Locate the driver side rear main brack-
et (Fig 22).
On the rear sport bar, pull o the
plastic cover that comes with the Jeep.
there are two metal clips that hold it in
place (Fig 23). Line up the driver side
rear main bracket over the holes of the
sport bar (Fig 24). Locate and insert
the included M8 screws and using the
included 5mm Allen head tool, tighten
the bracket in place (Fig 25). Repeat
on the Passenger side using the
passenger side rear main bracket.

6
Step 8: Installing the rear bow #1 to
the rear leg bracket
Locate the rear bow #1, (FIG27),
and the driver side rear leg bracket
#1(FIG26) installed from factory on the
driver side rear main bracket (FIG 22).
There are a pair of screws and nuts
installed on the rear leg bracket from
factory. Remove these screws and nuts
using a 10mm socket wrench and the
included 5mm Allen head tool and set
aside. (FIG 28)
Driver side rear leg
bracket #1
Passenger side rear
leg bracket #1
FIG 26
Rear Bow #2
Rear Bow #1
FIG 27
FIG 28
FIG 29
Rear Bow #1
Rear Bow #1
Driver side rear
leg bracket #1
FIG 30
Line up the driver’s side mounted rear
leg #1 to the rear bow #1. Insert the
screws and nuts and tighten using the
included 4mm Allen as shown in Fig
29.
Fold the Rear Bow #1 and the rear leg
#1 to the front (FIG30).
Repeat on the other side of the vehicle
Step 9: Installing the rear leg #2 to
the rear main bracket In the Driver’s
side rear main bracket, there is a
screw and nut installed from Factory
(Fig 31). Remove this screw and nut,
and set aside.
With the help of a friend carefully take
the top deck assembly out of the box
by grasping the rear legs #2 and bow
arms that are attached to the front of
the windshield header as shown in g
32 and lay down on the back of the
Jeep.
FIG 31
Screw & Nut
Driver side rear main
bracket.
Driver side rear
leg #1
Driver side rear
leg #2
Driver side bow
arm
FIG 32
Make sure the holes of the rear leg #2
and main bracket line up (g 33). Insert
the screw and nut previously removed
using a 10mm socket and the includ-
ed 4mm Allen head tool. Tighten and
secure the bracket (g 34 & 35).
FIG 35
FIG 34
FIG 33

7
Step 10: Hook and Loop Rear bow #1
Fold the Rear Bow #1 and the rear leg
#1 to the back (FIG 36).
In the deck there are three aps sewn
to the top deck. Locate the 3rd ap
sewn on the deck (FIG 37) and attach
the hook and loop around the rear bow
#1 as shown in g 38 & 39.
Rear Bow #1
Driver side
bow arm
Rear Bow #1
FIG 36
FIG 38 FIG 39
Hook
and loop
Flap sewn 1
32
Rear Bow #1
FIG 37
Step 11: Securing rear bow #1 &
rear leg #1
Once rear bow #1 is secure on the
deck, with the help of a friend, fold
back to the front, the rear bow #1 and
the rear leg #1 (FIG40).Once forward,
insert the pin to secure the rear bow as
shown in gs 41,41a & 42
Rear Bow #1
FIG 40
Pin securing leg #1
FIG 41
Driver side
rear leg #1
FIG 41a
rear leg #2
rear leg #1
Pin secure
FIG 42
FIG 43
Bow arm
FIG 44
Step 12: Installing the top Deck
On the front of the top deck, locate
the two bow arms attached to the front
windshield header (Fig 43). Pull the
front header and top deck fabric to
the windshield (FIG 44). Fold back the
front header exposing the two bow arm
ends.
The bow arms will install to the front
bow mount brackets located on the
top of the door surrounds. With the
help of a friend, lift each of the bow
legs over the bow mount bracket (Fig
45).

8
Step 12: Installing the top Deck (Continued)
Once lined up with the bow mount
bracket, install the header assembly by
pulling out the quick release knob and
push over the mount until you hear a
“click”(FIG45). Tighten the bow mount
brackets on the front door surround with the
included 4mm allen wrench (FIG45a). The
front header should now easily rest on top of
the windshield when folded down.
Repeat on the other side of the vehicle.
FIG 45a
FIG 45
Bow mount brackets
Quick release
FIG 46
corner pockets
FIG 47 FIG 48
square
bracket
FIG 49
FIG 50
Before you fold down the header make
sure that the front two header corner
pockets are in place and not lifted up
over the header (Fig 46). Slowly fold
down the front header.
With the header resting on the wind-
shield, close the front header latches
to secure the front of the top to the
windshield. See FIG’s 47 & 48.
Locate the driver side square bracket
on the rear driver door surround as
shown in Fig 49. Secure the deck to
the bracket by rolling the plastic into
the slot on the bracket as shown in Fig
50.
Repeat on the other side of the vehicle.
Go inside the vehicle and locate the
front bow, center bow #1 and
center bow #2 and the hook and
loop laps sewn into the top deck.
Wrap these flaps around the rst,
second & third center bows securing
the top deck to the bows (FIG 54 &
55).
Center Bow #1
Center Bow #2
Front Bow
FIG 51
Front Bow
Center Bow #1
Center Bow #1
Center Bow #2
FIG 54 FIG 55

9
FIG 56
FIG 57
Step 13: Installing the side quarter
windows
Locate the drivers rear quarter window.
Line up the driver’s side Quarter win-
dow to the zipper on the deck and zip it
as shown in FIG’s 56 & 57
On the rear of the quarter window there
is a corner support installed (FIG 58).
The quarter window corner support will
engage with the plastic corner up in
the upper corner the soft top hardware
(FIG 59).
Once the upper is secure, in the bottom
of the corner support is a tab that rests
on top of the corner bracket mount in-
stalled in step 5, see Fig 60 & 60a.The
corner bracket restsin this tab. Fig 61
FIG 58 FIG 59
Corner
Support
Plastic
corner
FIG 61
FIG 60
Corner
Support
Plastic
corner
Corner
Bracket
mount
Tab
FIG 60a
Step 14: Installing the rear window
Locate the rear window and line up
and slide the rear window into the “C”
Channel located at the top of the rear
portion of the top deck and slide it
across (FIGs 62 & 63).
Once both quarter windows and the
upper portion of the rear window are
secured to the top deck, line up the
driver’s side rear zipper on the Quar-
ter window to the zipper on the rear
window and zip it down a few inches
(FIG 64).
Repeat this on the passenger side of
the rear window. You may have to lift
the quarter window up to secure this
second zipper a few inches. Once both
side zippers are attached, zip the rear
window zippers down about half way
(Fig 65) making sure the top is cen-
tered over the rear bow.
FIG 62 FIG 63
Zip
down
a few
inches
FIG 64
FIG 65

10
When removing the quarter windows from the Top deck, make
sure the zipper is completely out of the “zipper box” before remov-
ing the window. See g 66 & 66a
NOTICE
FIG 66 FIG 66a
Step 15: Securing the Side and Rear
Windows to the Vehicle
As shown in g’s 67 & 68, roll the ver-
tical plastic strip into the door surround
slot securing it to the door surround.
Next, starting at the driver’s side front,
attach the side belt rail into the vehicle
body by “rolling” the plastic into the
slot (FIG 69 & 70).
Note: You may have to pull the cor-
ners around towards the front or back
of the vehicle to center the top on the
vehicle. If this is too dicult, release
the front windshield header latches.
Once installed the rst time these win-
dows will easily install. Repeat this on
the passenger side centering the top
over the rear bow.
FIG 67 FIG 68
FIG 69 FIG 70
Step 16: Securing the tailgate bar &
rear window to the vehicle
Take the tailgate bar and orient the
“C“-Channel with the round seal facing
down and slide the “C” Channel onto
the rear window retainer as shown in
FIG 71 & 72. After sliding the retainer
all the way through the “C” Channel,
roll the tailgate bar into the mounts
with the outside of the fabric facing to-
wards the rear of the Vehicle (Fig 73)
Once the Tailgate bar in secure, lower
zippers on both sides of the rear cur-
tain and move to the rear driver’s side
corner mounts and “roll” the plastic
into the corner mount as shown in FIG
74. Repeat this procedure on the
passenger side.
FIG 71FIG 74FIG 73
FIG 72

11
Once the Tailgate bar in secure, Close the hook and loops side flaps (FIG75) and the
upper rear flaps (FIG 76 & 77). Then, secure the rear zipper cover flap as shown in
Figs 78 & 79. Repeat this procedure on the passenger side.
FIG 79FIG 78
Using Your Complete Soft Top
Your Soft top hardware has multiple
front fold back options. Depending on
how much sun and weather you want to
let into the cab determines the options
available to you
Option #1 & #2
Open over the front driver and
passenger compartments:
Unlatch the two front Windshield
latches (Fig 80 & 81). Push the
front header up and over to open the
“sunroof”. Secure the two side straps.
When you open the front portion there
will be fabric still hanging down over
your head (Fig 82). This is Option #1
which provides protection from the sun
while opening the “sunroof”. Make
sure the two side straps are tightened
to the two bows (FIG 82a) on all
options.
FIG 80 FIG 81
Partially Open Front
(to protect from sun)
FIG 82
FIG 82a
Option #1
FIG 75FIG 76FIG 77

13
Fully Open Front
FIG 83
Option #2
FIG 83a FIG 83b
push front bow
to back
Using Your Complete Soft Top-
Continued
Option #2 Fully Opened Driver and
Passenger Sunroof
For the next position you will need
to slide the two side straps towards
the header as shown in g 83a and
push the front bow in the center of the
folded back “sunroof” and tuck/ fold it
under the header, which opens up the
“sunroof” completely (FIG83b).This
option is shown in Fig 83.
Option #3 & #4
Open over the front driver and pas-
senger compartments:
These options open both the front cab
and rear cab portions of the top. This
option requires you to remove the
front header arms and the two bows
from the bow mount brackets. Fig 84
shows the nished look of this “Sun
Roof” option with the front header
installed on the third bow bracket
mount and the header folded all the
way back to the rear of the vehicle.
With the header latches un-latched
and front sec-tion open, un-hook the
2 quick release knobs locat-ed on the
end of the header arms as circled in
Fig 84a. Next, un-hook the 4 quick
release knobs on bow #1 and bow #2
(Fig’s 84c, 84d 84e) leaving the two
rear bows (Bow #1 & #2) encased in
the hook and loop aps (Fig 84f, 84g).
Once The front bow arms and two
rear bows are disconnected from the
bow mount brackets, with the help of
a friend, carefully fold back the front
header and two bows layering the top
and bows under the fabric (Fig 84f)
and then connect the front bow arms
quick release brackets to the rear-
most third bow mount bracket. This
is option # 3. Notice in Fig’s.85, 85a &
85b (page 14) how the fabric is “lay-
ered” back and the front Bow Mount
Brackets are installed to the rear bow
brackets.
Also notice in Fig 85a how the side
bow straps are pulled up completely
towards the front header. This is op-
tion #4 with the entire fabric assembly
folded back and secured to the rear
brackets.
Option #3
Partially Open rear
(protects rear passenger from sun)
FIG 84
front bow
FIG 84a FIG 84b
FIG 84c
FIG 84d
Center bow #1
Center bow #2
FIG 84e FIG 84f
front bow Center
bow #1 Center
bow #2
FIG 84g

14
Option #4
Fully Open rear
FIG 85
FIG 85a
FIG 85b
TheThe front header arms must
be secure to the third bow mount
bracket and the fabric/ bows
must be layered back before the
vehicle is driven! Failure to secu-
re these bow mounts will cause
the top to potentially y o󰀨 the
vehicle causing damage to the
top, vehicle and potentially other
vehicles on the road.
WARNING
Folding back and securing the entire
top to the rear of the vehicle
To fold back the entire top assembly
to the rear of the vehicle and secure,
remove the rear and quarter windows
from your soft top. Unlatch the quick
release knobs (both sides) from the
front, Center #1, Center #2 bows (g
86), unhook the pin securing the rear
leg (g 86a). With the help of a friend,
fold back the entire top, folding it un-
der itself to the rear of the vehicle as
shown in g 87. Make sure the front
header tubes are secure inside the
vehicle and the front header is inside
the vehicle. Important: Go to page 15
to secure your folded down soft top!
FIG 86
Center Bow #1
Center Bow #2
Front Bow
Front leg
Unhook pin securing rear leg
FIG 86a
FIG 87

15
When folding back your soft top, it must always be secured to the vehicle using
the enclosed straps shown above. When the Top is folded back in the sun roof
position,make sure the quick release knobs are secure. Failure to do so may
result in damage to your vehicle, hardware system, soft top and your person.
WARNING
Threading Straps through Buckles:
For the above strap attachment you will need to thread webbing straps
through buckles. Please review the picture to the left for correct strap
routing through the buckles. As a rule of thumb, run the strap below
and through the sewn side of the buckle first and then back down
through the end of the buckle. Tighten the strap by simply pulling the
exposed webbing after threading the strap through the buckle.
Using Your Fastback Soft Top
Continued
To secure your soft top, locate the
two side tension straps (g 88). Hook
the end of strap under the belt rail
(g 89), insert the other side of the
tension strap through the strap that is
sewn onto the top for shipping located
on the front leg, see fig 90. Thread
through the buckle and tighten to
secure as show in fig 91 & 92.
Repeat on the other side of the
vehicle.
FIG 88
FIG 89
FIG 91 FIG 92
FIG 90
Strap Sewn

Care and Maintenance:
Your QuadraTop is made of the nest
materials available but to keep it looking
new and for the maximum possible wear,
it will need periodic cleaning and basic
maintenance. The main threats to your
soft top are pollutants, dirt and grime.
By keeping your soft top clean you will
prolong the life of your top.
We recommend the following to keep
your top like new:
Washing: The soft top fabric should be
washed often using a mild soap, warm
water and a soft bristle brush (do not use
the brush on the window glass!). You
can also use special soft top clean- ers
available on our website and shown on
page 15. Make sure that after clean- ing
you rinse with clear water to remove all
traces of soap.
Zippers: Keeping the zipper cleaned
and lubricated with a silicone lubricant
(see Page 15) will help prevent damage
and keep the zippers in a smooth work-
ing condition. If zipper opens behind the
slider, the slider may have been spread
apart. This problem can usually be xed
by using an ordinary pair of pliers to bring the
sides back into parallel. Return slider to the
end of the zipper in the normal Open posi-
tion. Squeeze lightly at rst and test zipper. If
the zipper continues to remain open squeeze
more rmly with pliers and try the zipper
again. Repeat procedure until your zipper
operates correctly.
Windows: It is very important that you keep
your QuadraTop windows clean! Use a mild
soap and water solution to gently clean your
windows. NEVER wipe your windows clean
with a dry cloth! Dust and dirt on a dry cloth
can scratch your windows causing “fog- ging”
and permanent damage. When re- mov-
ing your windows, store them with a towel
between the panels/rear win- dows to protect
them from damage. If frost or ice forms on
the outside of your windows during the win-
ter, DO NOT use an ice scraper to remove
this frost. Over time you will see small micro
scratches in your windows which are natural
wear and tear. These Micro scratches can be
“polished” out using the window polish listed
on page 15 (Available at Quadratec.com).
Water/Fabric: In the event of seeping
through the seams, 3M Scotchgard® may
be applied on the inside of the seams to stop
the see. Rips in the fabric may be repaired
with Bondex® iron on patches. Iron the
patches to the Inside of the top, carefully
following the Bondex® instructions.
Snaps: Keep snaps cleaned and lubricated
with silicone to help prevent snaps from
sticking to the studs. If a snap does become
stuck to a stud, use a screwdriver and GEN-
TLY pry apart to prevent permanent damage
to the snap or the top fabric.
16

Quadratec Limited Warranty
for QuadraTop® Replacement Soft Tops
Your QuadraTop® replacement soft top is
covered by the following Limited Warranty
provided exclusively by Quadratec, Inc. 1028
Saunders Lane, West Chester, PA 19380.
This Limited Warranty is the only warranty
made in connection with purchase. Qua-
dratec neither assumes nor authorizes any
vendor, retailer or other person or entity to
assume for it any other obligation or liability
in connection with this product or Limited
Warranty.
What is Covered:
Subject to the terms, exclusions and limita-
tions herein and with respect only to soft tops
rst sold in the United States, Quadratec
warrants to the initial retail purchaser only
that your QuadraTop soft top shall be free of
defects in material and workmanship for a
period of 3 years from date of initial retail
sale.
All other warranties are hereby disclaimed,
except to the extent prohibited by applicable
law in which case any implied warranty of
merchantabil- ity or tness for a particular
purpose on this prod- uct is limited to 3 years
from date of initial retail sale. Quadratec
reserves the rights to: (a.) require invoice or
other proof your soft top is within the terms
of this Limited Warranty as a condition of
warranty service and, (b.) make future revi-
sions to this product and Limited Warranty
without prior notice or obligation to upgrade
your soft top.
What is Not Covered:
Your Quadratec Limited Warranty does not
cover products or parts Quadratec determi-
nes to have been damaged by or subjec-
ted to: (a.) installation damage, alteration,
modication, failure to maintain or attempted
repair or service by anyone not authorized
by Quadratec, (b.) normal wear and tear,
cosmetic damage or damage from
water immersion, (c.) Acts of God, accidents,
misuse, negligence, inadequate mounting
or impact with vehicle(s), obstacles or other
aspects of the environment, (d.) theft, vanda-
lism or other intentional damage.
Remedy Limited to Repair/Replacement:
The exclusive remedy provided hereun-
der shall, upon Quadratec inspection and
at Quadratec’s option, be either repair or
replacement of product or parts (new or
refurbished) covered under this Limited
Warranty. Customers requesting warranty
consideration on QuadraTop soft top should
rst contact Quadratec to obtain a RGA
number (610-701-3336). All labor, removal,
shipping and installation costs are custo-
mer’s responsibility.
Other Limitations - Exclusion of Damages
- Your Rights Under State Law:
In consideration of the purchase price paid,
neither Quadratec nor any independent
Quadratec distributor/licensee are responsi-
ble for any time loss, rental costs, or for any
incidental, consequen- tial, punitive or other
damages you may have or incur in connec-
tion with any part or product purchased. Your
exclusive remedy hereunder
for covered parts is repair/replacement as
described above.
This Limited Warranty gives you specic
rights. You may also have other rights that
vary from state to state. For example, some
states do not allow limitations of how long an
implied warranty lasts and/or do not allow the
exclusion or limitation of incidental or con-
sequential damages, so the limitations and
exclusions herein may not apply to you.
The terms Quadratec®, QuadraTop®
Essentials® and Essential® are Registered
Trademarks of Quadratec Inc. Registered in
U.S. Patent and Trademark Oce.
©Quadratec, Inc. 2023. All Rights Reserved.
Version 8.28.23
Part # 941048.01
17