RAIS RAIS 86 User manual

RAIS CLASSIC SERIES
USER’S MANUAL
RAIS 86
RAIS 4
RAIS 106
RAIS A/S
Industrivej 20
9900 Frederikshavn
Denmark
Tel.: [phone]
Fax: [phone]
Tested Beaverton
& Listed by: Oregon USA
OMNI-Test Laboratories, Inc.
C

2
TABLE OF CONTENTS
INTRODUCTION .................................................................................................................3
Safety and Environmental Testing .................................................................................3
Features and Items Included .........................................................................................3
INSTALLATION ..................................................................................................................3
Precautions and Specifications......................................................................................3
Specifications.................................................................................................................5
Assembly Instructions....................................................................................................5
Chimney.........................................................................................................................6
OPERATING INSTRUCTIONS............................................................................................7
First Fire.........................................................................................................................7
Building the Fire.............................................................................................................8
Check for a Proper Burn ................................................................................................8
Cooking..........................................................................................................................9
FIREWOOD.........................................................................................................................9
Specifications.................................................................................................................9
Burning value of wood ...................................................................................................9
A Few Reminders ........................................................................................................10
CARE AND MAINTENANCE ............................................................................................10
Creosote – Formation and Need for Removal .............................................................10
Surfaces.......................................................................................................................11
Glass Doors .................................................................................................................11
Removing the Ashes....................................................................................................11
Cleaning the Smoke Box/Baffle System ......................................................................12
Firebox Lining ..............................................................................................................12
Gaskets........................................................................................................................12
TROUBLE SHOOTING .....................................................................................................13
WARRANTY......................................................................................................................13

3
Congratulations on your new RAIS wood burning stove. As a product of award
winning design and superior quality, we wish you many years of warmth and pleasure.
INTRODUCTION
We are asking you to:
PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE YOUR NEW RAIS STOVE.
FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,BODILY INJURY,OR EVEN
DEATH.KEEP IT HANDY FOR EASY REFERRAL.
Safety and Environmental Testing
The RAIS Classic Series stoves have been tested by OMNI-Test Laboratories, Inc. of
Beaverton, Oregon and are listed to UL 1482 and ULC S627. They are EPA exempt as
cook stoves.
Features and Items Included
Your RAIS has a built in convection system, so the sides do not get very hot. It also
creates air circulation in the room, to spread the heat faster and more evenly.
The RAIS 4 and RAIS 106 models have unique sliding doors - a RAIS specialty, which
enables you to operate them closed as a stove or open with a screen as a fireplace.
Included with the RAIS stove (in the firebox) are:
•Flue collar with 3 bolts/nuts (to connect to stove/pipe)
•An oven mitt and oven thermometer
•A box of RAIS starter matches
•Heat protective door handles
•Smoke plate hook (RAIS 4 and RAIS 106 only)
•A can of touch-up paint (Remove from the stove!)
Installation
Precautions and Specifications
IF THIS STOVE IS NOT INSTALLED PROPERLY,A HOME FIRE MAY RESULT.TO REDUCE THE RISK,
PLEASE CAREFULLY FOLLOW THE DIRECTIONS FOR INSTALLATION.
Consult your local Building Inspector or Fire Marshall before installation to
determine the need to obtain a permit. Also inquire about restrictions and
installation inspection requirements in your area.
If utilizing an existing chimney, it is suggested that you have a professional mason or stove
installer do a complete check-up of your chimney, liner, and flue.
In order for the stove to work and draw properly, sufficient air is important! Be especially
aware of any mechanical fans (e.g. kitchen or bathroom) that may affect the proper draw.

4
In addition, make sure that the floor and sub-flooring is designed to carry the extra weight
of the stove. The floor protector or plate must be made of a non-combustible material. It
must cover under the stove and extend 16” (40.6cm) (18” (45.7cm) in Canada) in front of
the stove door, 8” (20.3cm) beyond the sides of the door, and under the pipe and 2” (5cm)
beyond for back venting.
When installing the stove, the heat distribution to other rooms should be taken into
consideration. The approximate heating area (based on standard ceiling height) and
thermal output are:
Model Heating Capacity Thermal Output Optimal* (Range)
RAIS 86 969 ft²
(90m²) 20,500 BTU (6 kW) 14-24 kBTU (4-7kW)
RAIS 4 1,076
ft² (100m²) 23,900 BTU (7 kW) 17-34 kBTU (5-10kW)
RAIS 106 1,292
ft² (120m²) 27,300 BTU (8 kW) 21- 41 kBTU (6-12kW)
*Minimum stove draft pressure at above output – 0.06” WC (16 Pascals)

5
Specifications
Single wall connector stove pipe – 6” (15cm) diameter
Chimney pipe – Class A, UL-103 HT, 6” (15cm) diameter
Efficiency – 71-73% based on DS standard
Minimum distance to non-combustible material – 2” (5cm)
Note: Non-combustible must be solid cement or block (not brick or tile over combustible
material).
Minimum distances to combustible material – as shown:
Wall View Corner View
# Description RAIS 86 RAIS 4 RAIS 106
A Distance to combustible side wall 22” (56cm) 20.5” (52cm) 19” (48cm)
B Distance to combustible back wall 9.5” (24cm) 8.5” (22cm) 11” (28cm)
C Corner distance to side walls 15” (38cm) 14” (36cm) 11” (28cm)
All Models
D Connector pipe to side wall 28.5” (72cm)
E Connector pipe to back wall 12.5” (32cm)
F Corner pipe to side walls 18.5” (47cm)
G Distance to furniture 36” (91cm)
H Front floor protection - US
- Canada 16” (41cm) from door opening 18” (46cm)
I Side floor protection 8” (20cm) from door opening
Ceiling to top of stove 36” (91cm)
Ceiling to connector pipe 18” (46cm)
Note: A heat shield or protective wall may be used to reduce clearances if it meets the
NFPA requirements. Contact your local Building Inspector for proper guidelines.
Assembly Instructions
The Classic models all come assembled. To add the top plate on the RAIS 86, first check
that the soapstone is in good condition. Place the 4 white spacers evenly and center the
top plate. CAUTION: Soapstone is fragile, so please handle with care.
Mount the special RAIS collar using the included hardware. When installing the first piece
of pipe (at the stove), place the pipe over the collar, which is designed so any moisture or
creosote will drip back into the stove and burn away.
If using a crimped pipe, cut that section off at the bottom and place it over the collar.
Install the remaining stovepipe segments with the crimped end down whenever possible.
H
G
B
E
D A I
H
G
F C,I
F
C,I

6
Chimney
The RAIS stoves must be installed using a Class A UL 103 HT
approved factory-built chimney system or a code-approved
masonry chimney with a flue liner. In Canada, the installation must
conform to CAN/CSA-B365.The chimney must extend through the
roof at least 3’ (1m), and 2’ (.6m) above any structure within 10’
(3m).
The condition of the chimney and height is very important. We
suggest a total minimum height of 10’ (3m). Do not connect this
stove to a chimney flue serving another appliance.
Required Installation Components
A. Chimney Cap
B. Insulated Chimney
C. Storm Collar
D. Roof Flashing
E. Ceiling Support Box or Joist Shield/Firestop Spacer
F. Chimney Connector Pipe
For venting vertically into a Class A chimney, single wall pipe (at least 24 gauge) may be
used in the room where the stove is installed. Refer to the manufacturer’s instructions for
the connection to the listed chimney. The chimney/stove pipe must not be smaller than 6”
(15cm) in diameter.
For venting directly into a masonry chimney or through a thimble, the top of the single wall
pipe must be at least 18” (46cm) below a combustible ceiling and conform to NFPA 211
guidelines and methods. See diagram below.
For rear venting or other not listed configurations, consult the local building codes and
follow the NFPA 211 guidelines.
B.
A.
E.
F.
C.
D.
B.
Chimney
Flue
Masonry
Insulate
d
Chimney
Connector Pipe
18” (46cm) below ceiling
Min.
2” (5cm)
Min.
2” (5cm)

7
If the stovepipe is fitted with a baffle, it must be manually operated, visibly placed for ease
of use, and must not close completely. Consult your chimney expert if you have any
questions. Important! Make sure that there is easy access to the chimney cleanout
door.
Operating instructions
First Fire
Your new RAIS should be broken in gently for top performance and to prevent paint
damage, cracks in the firebrick, and excessive wear and tear.
Start with a small fire (never overload the firebox) to allow the materials to get
accustomed to the higher temperatures, and then gradually increase the intensity. Use up
to a maximum of 2 logs. As a safety precaution when the fire heats up, use the
protective door handles.
For the first few fires you may detect a strange smell that comes from "heat treating" the
paint and materials. This is normal and will soon disappear. Just insure there is plenty of
fresh air in the room!
Furthermore, during the initial heating up and cooling down, some "click-sounds" may
occur from the metals being exposed to the large differences in temperature. This is
normal.
For wood to burn correctly, the right amount of air has to be supplied at the right
time and places.
Primary air is defined as combustion air for burning the “mass of wood" and stimulates
production of volatile gases.
Secondary air is used to burn off the gases at high temperatures (above 1,000°F (540°C))
and to keep the glass free of soot.
Basically, the primary air is used to start the fire, and the secondary air is used to maintain
the fire.
The RAIS 4 and RAIS 106 stoves are equipped with an air control handle on the left side
just below the door. When the handle is pushed all the way right to Position 1, the primary
air and secondary air are both fully open. When the handle is pushed left to the center to
Position 2, the stove gets only the full secondary air, and if the handle is pushed to the far
left toward Position 0, the air supply is reduced. At Position 0, the stove will shut down.
On the RAIS 86, the air controls are vents located on the front of the doors. Open both
vents (to the right) for Position 1. Close the top vent to the left for Position 2, and
Position 0 is when both vents are closed.

8
The handle on the right side just below the door controls the shaker grate. It simplifies the
cleaning of the stove. You just shake the ashes through the grate into the ash pan.
Refer to Removing the Ashes in the CARE AND MAINTENANCE Section of the
Manual for detailed directions.
Firewood used should be seasoned, split wood with an adequate low degree of moisture
(15 - 22%), and ideally about 12 - 14” (30 - 36cm) in length and for the RAIS 86, 10 - 12”
(25 - 30cm). In order to get “dry wood”, it should be stored in a dry place under a roof with
sufficient fresh airflow for at least one full year for softer woods and a minimum of two
years for hardwoods.
Only use the wood fuel as described in the FIREWOOD Section of this manual!
Building the Fire
To start the fire lay a few pieces of kindling or dry twigs and paper at the back of the
firebox (enough for a small fire). Build the wood directly on the stove hearth, and do
not use a grate or elevate the fire.
Set the air control to Position 1. On the RAIS 4 and RAIS 106, open the baffle plate (lift the
handle on the right to a vertical position). Also, a smoke plate located at the top in the
firebox can be pulled forward to help the smoke exit faster. Use the smoke plate hook to
move and adjust the smoke plate. Light the fire, and during start up you can leave the door
slightly cracked (with supervision) until the kindling is burning well.
Add 1 or 2 split logs on the kindling fire and allow enough time for them to catch on fire
(about 2 - 5 minutes). Now close the door completely, and set the air control to Position 2.
Further adjustments to the air control may be made later on if necessary. Never reduce
the air intake to Position 0 while logs are still burning. This will cause incomplete
combustion (creosote), risk of explosion, and soot on the glass. Once the door is
closed and burning correctly, the stove does not require supervision. Adjust the baffle plate
to horizontal and push back the smoke plate.
The RAIS Classic Series was developed to an optimal thermal output of 20,500-27,300
BTU/hr (6-8 kW) with a water content of 18%, which corresponds to about 4-4½ lbs
wood/hour. If the fire is fed more than recommended, there is a danger that the stove will
be overloaded and might discolor. Over firing is unnecessary and will void the
warranty.
Check for a Proper Burn
For a proper burn, the inside of the firebox and the glass panel should be free of soot, and
the ashes in the bottom should be light gray (not black). To allow more air in to the heating
chamber, open up the air controls (handle/vents to the right).
For normal operation the air control should be set at Position 2. However, if the wood is
burning too quickly, you can adjust the air control (handle/vents toward the left).

9
To ensure a proper and safe combustion, there should be bright and lasting
flames/embers. Don't let the wood smolder. Do not close the air inlets completely
during normal usage.
The RAIS 4 and RAIS 106 can also be burned as a fireplace with the doors open. For safety, keep
the screen on the fireplace opening at all times.
Cooking
You can both cook and bake in your RAIS stove. Learning how to control the oven heat in
a wood stove is a matter of trial and error. Your RAIS stove comes with an oven
thermometer, which helps in the learning process.
For most baking needs, bring the temperature up to 300-400°F (150-200°C). If the oven
temperature gets too high (above 425°F (220°C)), open up the oven door for a few
minutes.
Always protect the soapstone liner with foil. Frozen dishes such as pizzas can be put
directly in the preheated oven without first defrosting.
A grill rack is available for the RAIS 4 and RAIS 106 for grilling in the firebox. Open the
baffle plate and doors to grill, and supervise at all times.
The top portion directly above the oven can serve as a warming area for plates or coffee,
or even for rising dough.
Each cook will discover what works best for his or her particular stove. Bon Appetit!
Firewood
Specifications
Only burn wood that has been seasoned for at least one full year (2 years is best!). If the
wood has not been "seasoned" or dried, much of the energy of the fire will go into
evaporating the water. Furthermore, condensation or creosote might occur in the stove
and pipe if you burn moist wood.
The log size should be about 2” (5cm) less than the width of the firebox.
Burning value of wood
Air-dried wood has less moisture (15 - 20%) than freshly cut timber (40%+), and typically
yields 20% more available heat. Wet wood burns at a lower temperature and causes
incomplete combustion (soot and "creosote" formation, which in extreme cases, can lead
to a chimney fire).
All types of wood heat up equally per pound (kilogram); however, the density of wood is
not the same, as shown in the following table:

10
Type of wood Dry Wood - Lbs/ft³ (Kg/m³) Compared to beech
Beech and Oak 36.2 (580) 100%
Ash 35.6 (570) 98%
Maple 33.7 (540) 93%
Birch 31.8 (510) 88%
Mountain pine 30.0 (480) 83%
Fir 24.3 (390) 67%
Poplar 23.7 (380) 65%
A Few Reminders
•Store your wood cut and split (split logs dry faster).
•Keep the woodpile in a dry sunny place, protected from the rain. Don't cover the pile
with plastic, because that will prevent the wood from drying out properly.
•Stack the wood with enough space between the rows to ensure good air circulation!
Fuel Caution
Do not burn trash (plastics and other trash emit harmful gases), driftwood, treated wood,
artificial logs, or non-seasoned wood.
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid,
naphtha, engine oil, or similar liquids to start or “freshen up” a fire in this heater.
Keep all such liquids well away from the heater while it is in use.
CARE AND MAINTENANCE
Although your RAIS stove requires little day-to-day upkeep, it is important to maintain it for
your safety and enjoyment.
IMPORTANT:
YOU SHOULD HAVE YOUR CHIMNEY AND STOVE CHECKED ONCE EVERY 2MONTHS DURING THE
HEATING SEASON OR AT LEAST ONCE A YEAR BY A PROFESSIONAL CHIMNEY SWEEP AND CLEANED
AS NEEDED.
Creosote – Formation and Need for Removal
When wood is burned slowly, it produces tar and other organic vapors, which combine with
expelled moisture to form creosote. The creosote vapors condense in the relatively cool
chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue
lining. When ignited this creosote makes an extremely hot fire.
The chimney connector and chimney should be inspected once every two months during
the heating season to determine if a creosote buildup has occurred.

11
If creosote has accumulated it should be removed to reduce the risk of a chimney fire.
Surfaces
The outer surfaces can be wiped with a dry soft rag, and if needed, a small amount of mild
detergent, but try not to scrub!
Minor scratches and other surface damage can easily be touched up with the RAIS paint
supplied with each stove. Remove any dirt, tar, and rust, and make sure repairs are made
only when the stove is cool (room temperature).
Soapstone stains can be cleaned with alcohol or it can be lightly sanded.
Glass Doors
The glass can be easily cleaned by wiping with a damp rag dipped in some of the ashes. A
good commercial glass cleaner can also be used.
If the glass should break, carefully remove the door/s. On the RAIS 86, lift it off the hinges,
and on the RAIS 4 and RAIS 106 remove/save the locking pins and slide the doors back
and out. Use a long nose punch (size 5/32 flat head) to gently tap out the locking pins
located at the sides on the band above the doors.
Place and steady the doors on a flat clean surface.
Remove the 4 screws from the back, and gently take out the inner frame assembly. Then,
remove all the loose pieces of glass and replace only with a 4mm ceramic new glass panel
and gasket available from an authorized RAIS dealer.
Assemble the inner frame, tighten the screws evenly (star formation), replace the door/s,
and gently tap the locking pins from the outside on the stove for the RAIS 4 and RAIS 106.
Removing the Ashes
Start by cleaning out the firebox. Use the shaker grate to remove the ashes through the
grate. A tray is in the ash drawer beneath the firebox.
Remember to leave some of the ashes in the firebox (about a 2”/5cm layer) for better
insulation! Be sure to put the tray back in the ash drawer, since it also serves as a
reflection shield.
DISPOSAL OF ASHES:
ASHES SHOULD BE PLACED IN A METAL CONTAINER WITH A TIGHT FITTING LID.THE CLOSED
CONTAINER OF ASHES SHOULD BE PLACED ON A NONCOMBUSTIBLE FLOOR OR ON THE GROUND,
WELL AWAY FROM ALL COMBUSTIBLE MATERIALS,PENDING FINAL DISPOSAL.
IF THE ASHES ARE DISPOSED OF BY BURIAL IN SOIL OR OTHERWISE LOCALLY DISPERSED,THEY
SHOULD BE RETAINED IN THE CLOSED CONTAINER UNTIL ALL CINDERS HAVE THOROUGHLY
COOLED.

12
Cleaning the Smoke Box/Baffle System
1. Remove the two baffle plates on the RAIS 86 as follows:
a. Lift out the smaller plate near the back first (#1), and then the larger baffle plate on
top (#2). See the view below:
B a c k R A IS 8 6
S to v e
# 1
# 2
2. Remove the smoke plate on the RAIS 4 and RAIS 106 as follows:
a. RAIS 4 – Raise the smoke plate up, turn it at a 90°angle (vertical), and pull it out through
the door opening.
b. RAIS 106 – First unscrew the two bolts on the sides holding the brackets, and hold on to
the smoke plate. Lift the smoke plate up, turn it at a 90°angle (vertical), and pull it out
through the door opening.
3. Use a small brush or rag to clean out the smoke box and vacuum if necessary.
4. The baffle and smoke plates can now be put back, and make sure they are properly put back in
place.
Firebox Lining
The firebox lining (bottom and sides) is made out of firebrick, which protects the outer steel
plates from overheating. With time small cracks might appear, and this is normal. If it
breaks however, it must be replaced.
Gaskets
It is recommended to replace the door gaskets about every 2 years. When replacing the
door gasket, make sure the door glass is not pressed too hard against the gasket. The
gasket around the ash drawer can also be replaced as needed. Gaskets can be obtained
from an authorized RAIS dealer.

13
Trouble shooting
Problem Possible Cause/Solution
Smoke
coming out of
the door
There may not be enough draft in the chimney (<0.06” WC (<16
Pascals)). Check for an obstruction.
Soot on the
glass Take care that the stove is warmed up sufficiently before closing the door.
The stove is
burning too
quickly
Check the door gaskets first and replace if needed. The chimney could
also be too high and thus create too much draft (>0.09” WC (>22
Pascals)). A damper may be needed.
The stove is
burning too
slowly
It could be due to too little air getting to the stove. Check that you're not
running exhaust fans (kitchen/bath), the chimney is not blocked, or there
is a leak between the chimney, the stovepipe, and the stove.
If the problem continues or other conditions, we recommend that you contact your chimney
sweep or your dealer.
If you should experience a chimney fire, quickly close all doors, dampers, vents, and call
you local fire department. Don't use water to extinguish the fire.
Warranty
We offer a 5-year warranty on your RAIS stove, which covers any defect in material or
workmanship. It does not cover damage from misuse or neglect. The glass, gaskets, and
firebrick are not covered.
ENJOY YOUR NEW RAIS!