RAIS 700 User manual

ENGLISH RAIS - manual for RAIS 700
1
User manual
Manuel d’utilisateur
Gebruikershandleiding
RAIS 700

ENGLISH MANUAL...............................................................2-29
FRANÇAIS MANUEL D’UTILISATEUR ................................30-51
FLEMISH GEBRUIKERSHANDLEIDING ...............................52-73
Manufacturer’s Plate for RAIS 700
Plaque signalétique de RAIS 700
Merkplaatje voor RAIS 700
EN 13229:2001+A2:2004 Raumheizer für feste Brennstoffe
Appliance fired by wood
Poêle pour combustibles solides
Produced at:
RAIS A/S, Industrivej 20, 9900 Frederikshavn, Danmark
VKF-NR:
XXXXX
Bauart: 2
15a B-VG
EC.NO: 709
Anordningen må kun installeres i forbindelse med ubrændbart materiale.
AFSTAND TIL BRÆNDBART, BAGVÆG
ABSTAND ZU BRENNBAREN BAUTEILEN, HINTEN
DISTANCE TO COMBUSTIBLE BACK WALL
DIST. ENTRE COMPOSANTS COMBUSTIBLES, ARRIÈRE
AFSTAND TIL BRÆNDBART, SIDEVÆG
ABSTAND ZU BRENNBAREN BAUTEILEN, SEITE
DISTANCE TO COMBUSTIBLE SIDE WALL
DISTANCE ENTRE COMPOSANTS COMBUSTIBLES, COTÉ
AFSTAND TIL BRÆNDBART, MØBLERING
ABSTAND VORNE ZU BRENNBAREN MÖBELN
DISTANCE TO FURNITURE AT THE FRONT
DISTANCE ENTRE COMPOSANTS COMBUSTIBLES, DEVANT
CO EMISSION
CO EMISSION IN DEN VERBRENNUNGSPRODUKTEN
EMISSION OF CO IN COMBUSTION PRODUCTS
EMISSION CO DANS LES PRODUITS COMBUSTIBLES
NOMINEL EFFEKT / HEIZLEISTUNG /
THERMAL OUTPUT / PUISSANCE CALORIFIQUE:
RØGGASTEMPERATUR / ABGASTEMPERATUR /
FLUE GAS TEMPERATURE / TEMPÉRATURE DES GAZ DE FUMÉE:
VIRKNINGSGRAD / ENERGIEEFFIZIENZ /
ENERGY EFFIENCY /EFFICACITÉ ÉNERGÉTIQUE:
DK: Brug kun anbefalede brændsler. Følg instrukserne i brugermanualen.
Anordningen er egnet til røggassamleledning og intervalfyring.
DE: Lesen und befolgen Sie die Bedienungsanleitung.
Zeitbrandfeuerstätte. Nur empfohlene Brennstoffe einsetzen.
UK: Fuel types (only recommended) Follow the installation and
operating instruction manual. Intermittent operation.
F: Remarque: Veillez lire et observer les instructions du mode d'emploi.
Foyer à durèe de combustion limitèe, homologué pour cheminée à
connexions multiples. Utiliser seulement les combustibles recommandés.
Hergestellt für /Produced for:
ATTIKA FEUER AG, Brunnmatt 16, CH-6330 Cham / RAIS A/S, Industrivej 20, DK-9900 Frederikshavn
STØV / STAUB /
DUST / POUSSIÈRES: DK: 8 mg/Nm³ / DE: 8 mg/Nm³ UK: 8 mg/Nm³ / FR: 8 mg/Nm³
DK: 268°C / DE: 268°C
UK: 268°C / FR: 268°C
DK: 5,2 kW / DE: 5,2 kW
UK: 5,2 kW / FR: 5,2 kW
DK: 80% / DE: 80%
UK: 80% / FR: 80%
DK: BRÆNDE
DE: HOLZ
UK: WOOD
FR: BOIS
DK: SE BRUGERVEJLEDNING
DE: SIEHE BEDIENUNGSANLEITUNG
UK: SEE USER MANUAL
FR: CONSULTEZ LE GUIDE DE L'UTILISATEUR
DK: SE BRUGERVEJLEDNING
DE: SIEHE BEDIENUNGSANLEITUNG
UK: SEE USER MANUAL
FR: CONSULTEZ LE GUIDE DE L'UTILISATEUR
DK:700 mm/SE BRUGERVEJLEDNING
DE:700 mm/SIEHE BEDIENUNGSANLEITUNG
UK:700 mm/SEE USER MANUAL
FR:700 mm/CONSULTEZ LE GUIDE DE L'UTILISATEUR
DK: 0,1%
DE: 0,1% / 1250 mg/nm³
UK: 0,1%
FR: 0,1%
15
RAIS 700
CE LABEL
RAIS 700

ENGLISH MANUAL...............................................................2-29
FRANÇAIS MANUEL D’UTILISATEUR ................................30-51
FLEMISH GEBRUIKERSHANDLEIDING ...............................52-73
Manufacturer’s Plate for RAIS 700
Plaque signalétique de RAIS 700
Merkplaatje voor RAIS 700
1
3
2
5
7
6
4
Position 1
Position 1
Stand 1
Position 2
Position 2
Stand 2
Position 3
Position 3
Stand 3

We cannot be held responsible for any misprints.
The oven is wrapped in packaging that is recyclable. This must
be disposed of according to national rules regarding the dis-
posal of waste.
The glass can not be reused.
The glass should be discarded along with the residual waste
from
ceramics and porcelain.
Pyrex glass has a higher melting temperature and therefore can
not be reused.
If discarded you make an important positive contribution to
the environment.
FIRE ENVIRONMENTALLY FRIENDLY!
5 Eco-friendly advices for sensible heating
- common sense both environmentally and economically.
1. Effective lighting. Use dry brushwood, kindling and possible a piece of news
paper. Open the air damper, so plenty of air is fed to the stove and the gases
from the heated wood can burn rapidly.
2. Light the fire with only little wood at a time - this gives the best combustion.
Remember plenty of air for every time new wood is added.
3. When the flames are diminished, adjust the air damper so that the air supply
is reduced
4. When only glowing embers remain, air flow can be reduced further, so heat-
ing demand is just covered. With a lower air supply the charcoal will burn
slower and the heat loss through the chimney is reduced.
5. Use only dry wood - ie wood with a humidity of 15 to 22 percent.

ENGLISH RAIS - manual for RAIS 700
5
Rais 700
Revision: 3
Dato : 24-10-2018
INTRODUCTION ............................................................................................................4
WARRANTY ..................................................................................................................4
SPECIFICATIONS ............................................................................................................5
INSTALLATIONS INSTRUCTIONS......................................................................................6
CONVECTION ...............................................................................................................7
CHIMNEY...................................................................................................................7-8
VENTILATION.................................................................................................................9
INSTALLATION .......................................................................................................10-11
INSTALLATION DISTANCE .......................................................................................12-17
FUEL ......................................................................................................................18-19
REGULATION OF COMBUSTION AIR ............................................................................19
USING THE WOOD BURNING STOVE ..........................................................................20
ADJUSTMENT OF AIR DAMPER ...................................................................................20
CONTROL....................................................................................................................20
FIRST USAGE ...............................................................................................................20
IMPORTANT - WARNING NOTE ...............................................................................21-22
LIGHTING AND FUELLING ...........................................................................................23
CLEANING AND CARE ................................................................................................24
CLEANING OF THE FLUE WAYS....................................................................................25
INTERRUPTION OF OPERATION ...................................................................................26
ACCESSORIES AND SPARE PARTS ................................................................................27

ENGLISH RAIS - manual for RAIS 700
6
Distributor:
Date:
Introduction
Thank you for purchasing a RAIS wood burning stove.
These appliances have been approved by HETAS Ltd as
intermittent operating appliances for burning wood logs only.
A RAIS wood burning stove is more than just a heat source: it also shows that you care
about design and quality in your home.
To make the most of your wood burning stove it is important that you read the manual
thoroughly, before installing and using it.
In the case of warranty coverage, and for general queries regarding your wood burning
stove, it is important that you know the stove’s production number.
We therefore recommend that you note down the number in the table below. The pro-
duction number is located in the top of the convex box.
Warranty
Your RAIS wood burning stove comes with a 5 year warranty. The warranty, however,
does not cover heat-insulating materials, glass and seals.
Any alterations made to the stove will void the warranty.

ENGLISH RAIS - manual for RAIS 700
7
Specifications
RAIS 700
Nominell output (kW): 5,2
Min./Max. output(kW): 3-7
Heating area (m2): ca. 60-105
Stove’s width/depth/height (mm): 825-485-535
Combustion champer’s width/depth/height (mm): 562-289-300
Recommended amount of wood when fuelling (kg):
(Distributed on 2-3 logs of wood approx. 25 cm)
1,8
Min. uptake (Pascal): -12
Weight (kg): 125
Efficiency (%): 80
Particles after NS3058/3059 (g/kg): 2,6
Dust measured according to Din+(mg/Nm³): 8
Smoke gas mass flow (g/s): 5,1
Smoke gas temperature (°C)
with Nominal output
268
Intermittent operation: Fuelling should be undertaken
within 3 hours.

ENGLISH RAIS - manual for RAIS 700
8
Installation instructions
The following pages give instructions for the safe and proper installation of this heating
appliance in the UK. These instructions cover the basic principles of installation, although
detail may need slight modification to suit particular local site conditions. In all cases the
installation must comply with current UK Building Regulations, Local Authority Byelaws
and other specifications or regulations as they affect the installation of the stove. Please
note that it is a legal requirement under England and Wales Building Regulations that
the installation of the stove is either carried out under Local Authority Building Control
approval or is installed by a Competent Person registered with a Government approved
Competent Persons Scheme. HETAS Ltd operate such a Scheme and a listing of their Reg-
istered Competent Persons can be found on their website at www.hetas.co.uk.
It should be noted that the current Building Regulations requirements are given in Ap-
proved Document J. These requirements may also be met by adopting the relevant recom-
mendations given in British Standards BS 8303, BS 6461 and BS 7566.
WARNING: Health and Safety Advice Notice
The installation of this heating appliance is governed by the Health and Safety at Work
Act 1974. It is the responsibility of the installer to ensure that all requirements of this Act
are met during the installation works. Attention is drawn in particular to the following:
Handling: The appliance is a heavy item and adequate facilities must be available for
loading, unloading and site handling.
Fire Cement: Some types of fire cement are caustic and should not be allowed to come
into contact with the skin. Protective gloves should be worn when handling
fire cement. In case of contact with the skin wash immediately with plenty
of water.
Asbestos: This stove contains no asbestos. If there is a possibility of disturbing any
asbestos in the course of installation then please seek specialist guidance
and use appropriate protective equipment.
Metal Parts: When installing or servicing this stove care should be taken to avoid the
possibility of personal injury.
Important Warning –Preparatory Work and Safety Checks:
• This stove must not be installed into a chimney that serves any other heating appli-
ance.
• There must not be an extractor fan fitted in the same room as the stove as this can
cause the stove to emit fumes into the room.
• If this appliance is installed into an existing chimney, the chimney must first be swept
and examined for soundness and suitability before the appliance is installed (see also
section headed “Chimney”).

ENGLISH RAIS - manual for RAIS 700
9
Convection
RAIS stoves are convection stoves. This means that the stove’s back and side panels are
not over-heated. Convection means that there is a circulation of air, which ensures that
the heat is distributed more evenly throughout the entire room. The cold air is sucked in
at the base of the stove up through the convection channel, which runs along the stove’s
combustion chamber. The heated air pours out at the top of the stove, which ensures a
circulation of warm air throughout the room.
The stoves are equipped with “cold” door handles – RAIS special feature – which means
you could almost do away with gloves. Be aware, however, that all exterior surfaces be-
come hot during use - so take extreme care.
Chimney
The chimney is the driving force which makes the stove function. In order for the stove to
perform satisfactorily the chimney height must be sufficient to ensure the correct draught
of 14 to 18 Pa so as to clear the products of combustion and prevent problems of smoke
emanating into the room when firing.
NOTE: A chimney height of not less than 4.5 metres measured vertically from the outlet
of the stove to the top of the chimney should be satisfactory. Alternatively the calcula-
tion procedure given in BS 5854:1980 may be used as the basis for deciding whether a
particular chimney design will provide sufficient draught.
The outlet from the chimney should be above the roof of the building in accordance with
the provisions of Building Regulations Approved Document J.
If installation is into an existing chimney then it must be sound and have no cracks or
other faults which might allow fumes into the house. Older properties, especially, may
have chimney faults or the cross section may be too large i.e. more than 230 mm x 230
mm. Remedial action should be taken, if required, seeking expert advice, if necessary. If it
is found necessary to line the chimney then a flue liner suitable for solid fuel must be used
in accordance with Building Regulations Approved Document J.
Any existing chimney must be clear of obstruction and have been swept clean immedi-
ately before installation of the stove. If the stove is fitted in place of an open fire then the
chimney should be swept one month after installation to clear any soot falls which may
have occurred due to the difference in combustion between the stove and the open fire.
If there is no existing chimney then either a prefabricated block chimney in accordance
with Building Regulations Approved Document J or a twin walled insulated stainless steel
flue to BS 4543 can be used. These chimneys must be fitted in accordance with the manu-
facturer’s instructions and Building Regulations.

ENGLISH RAIS - manual for RAIS 700
10
A single wall metal fluepipe is suitable for connecting the stove to the chimney but is not
suitable for using for the complete chimney. The chimney and connecting fluepipe must
have a minimum diameter of 150 mm and its dimension should be not less than the size
of the outlet socket of the stove which is 150 mm in diameter. Any bend in the chimney
or connecting fluepipe should not exceed 45°. 90°bends should not be used.
Combustible material should not be located where the heat dissipating through the walls
of fireplaces or flues could ignite it. Therefore when installing the stove in the presence
of combustible materials due account must be taken of the guidance on the separation
of combustible material given in Building Regulations Approved Document J and also in
these stove instructions.
If it is found that there is excessive draught in the chimney then either an adjustable flue
damper or alternatively a draught stabiliser should be fitted. The adjustable flue damper
should not close off the flue entirely but should in its closed position leave a minimum
continuous opening free area of at least 20 % of the total cross sectional area of the flue
or fluepipe.
Adequate provision e.g. easily accessible soot door or doors must be provided for sweep-
ing the chimney and connecting fluepipe.
You should also familiarise yourself with the draught conditions for chimneys with 2 flues.
The flue outlet spigot is 150 mm in diameter.
For strong draughts, the chimney or flue should be fitted with a draught stabiliser. In
which case, it is important to ensure that there is a free flow-through area of minimum
20 cm² when the regulating gate is shut. Otherwise, the fuel energy may not be used
optimally. If, at any time, you are unsure about the condition of the chimney, you should
contact a chimney sweep.
Remember that access to the access door should be kept clear.

ENGLISH RAIS - manual for RAIS 700
11
Ventilation - make the best possible use of the inserts.
The stove is equipped with four convection air outlet, which may be connected with suit-
able air ducts to other rooms.

ENGLISH RAIS - manual for RAIS 700
12
Installation
It is prohibited to carry out unauthorised alterations to the stove.
There must be plenty of fresh air in the room where the stove is being installed, in order
to ensure proper combustion. Note that any mechanical exhaust ventilation - e.g. an
extraction hood - may reduce the air supply. Any air grates must be placed in such a man-
ner, that the air supply is not blocked.
The stove is equipped with four convection air outlets, which may be connected with suit-
able air ducts to other rooms.
Building Regulations Approved document J gives specific guidance on the required
permanent ventilation into the room for combustion air of solid fuel appliances.
The floor structure must be able to carry the weight of the wood burning stove, as well as
the weight of a chimney, if necessary.
When you choose where to set up your RAIS wood burning stove, you should consider
the heat distribution to the other rooms. This will enable you to get the best use out of
your stove. The stove should be set up at a safe distance from inflammable materials. See
the manufacturer’s plate on the wood burning stove.
Installation of stove:
NOTE:Decision to be taken concerning the placement of the inlets and outlets of the
convection system. The area requirements for convection holes to be kept.
Miscolouring of the wall above the doors and the convection air outlets may
occur due to raising hot air.
RAIS cannot take responsibility for building in or consequential damage.
The stove to be inspected for defects at receipt.

ENGLISH RAIS - manual for RAIS 700
13
Lift the stove from the pallet to the place of installation on a suitable floor protection. The
stove can be mounted with rack and adjustable leg (buy accessories at your local RAIS
dealer)
The stove is aligned by adjusting screws, so the lower edge of the glass door is in horizon-
tal position and the surface of the door is vertical when the door is closed.
Remove the front plate and door from the stove. Be careful not to damage the glass on
the door. Protect the painted stove body against spray of cement and paint.
Install the uninsolated flue pipe on the flue outlet inside the convection box.
It is important that there are no leakage between the flue pipe and the stove. It is re-
commended to seal the connection by suitable gasket or compound.
Install the insulated flue pipe and connect to chimney.
Install fresh air inlet connection to the pipe stub if such is to be installed (if chosen).
If pipes are intended installed on the outlets of the convection system this is recommen-
ded before building further.
The stove is now ready for building into either panels or brick wall.
After establishing the wall and eventually
painted, the fronts and covers are mounted
again. Remove all protective plastic and tape.
It is possible to deliver front panels in special measures if needed together with the stove.
Contact your local RAIS dealer.

ENGLISH RAIS - manual for RAIS 700
14
Mounting distance for panelled wall – combustible material
Insulation ability such Aqua panel (coefficient of thermal conductivity 0,36 W/mk) or
better.
A-A
A
A
110Min. mm
850
min.mm
Clearance
400
min.mm
Distance
300material min . mm
Distance to combustible
(e.g. side wall)
200material min. mm
Distance to combustible
(e.g. door frame)
100Min. mm
100Min. mm
300
Min.mm
Min. convection area
above the stove: 800 cm²
(may be distributed)
Min. convection area
below the stove: 530 cm²
(may be distributed)
300
materialmin.mm.
Distancetocombustible
NB!!
Insulated chimney
down to the
smoke connector.
Floor plate
700min. mm
Distance to furniture

ENGLISH RAIS - manual for RAIS 700
15
A-A
A
A
Min. convection area
above the stove : 800 cm²
(may be distributed)
Min convection area
below the stove: 530 cm²
(may be distributed)
300
materialmin.mm
Distancetocombustible
850
min.mm
Clearance
400
min.mm
Distance
110Min. mm
50Min. mm
50Min. mm
200area min. mm
Distance to combustible
(e.g. door frame)
300area min. mm
Distance to combustible
(e.g. side wall)
300
Min.mm
700min. mm
Distance to furniture
Floor plate
NB!!
Insulated chimney
down to the
smoke connector.
Mounting distance - super isol

ENGLISH RAIS - manual for RAIS 700
16
Mounting distance for brick wall / firewall
A-A
B-B
A
A
B B
Min. convection area above the stove 800
cm² (may be distributed)
Distance to combustible material min. 300 mm
Min. convection area below the stove
400 cm² (may be distributed)
Distance to non-combustible material
0 mm (10mm recomended) Distance to non-combustible material
0 mm (10mm recomended)
Clearance min. 850 mm
Distance min. 400 mm
Distance to furniture
min. 700 mm
110 mm
If you want smaller distance. You
must use a special adapter.
7091301sv (not enclosed)

ENGLISH RAIS - manual for RAIS 700
17
Mounting distance - (height x width) 545 x 840
A wood burner insert should never fit tightly. Steel expands when heated.
Aqua panel
Super isol
Brick wall
545
Min.mm
850
Min. mm
415
Min.mm
5Min. mm
1025
Min.mm
590
Min.mm
545
Min.mm
5Min. mm
581
Min.mm
925
Min.mm
545
Min.mm
5Min. mm
Note!
For reasons of adjustment options
for adjusting screws must be the
foundation level for min. 5 mm
below the horizontal edge in front

ENGLISH RAIS - manual for RAIS 700
18
J-J
J J






















ENGLISH RAIS - manual for RAIS 700
19
Installation distance in case of combustible wall
To find out whether the wall next to where the stove is going to be installed is flammable,
you should contact your building contractor or the local building authorities.
The hearth should be able to accommodate the weight of the stove. The chimney must
be independently supported by wall brackets or a ceiling support plate. The weight of the
stove is indicated in the brochure.
The stove should always be installed on a non-combustible hearth of a size and construc-
tion that is in accordance with the provisions of the current UK Building Regulations Ap-
proved Document J.
If the stove is to be installed on a wooden floor, it must be covered with a noncombustible
material at least 12mm thick, in accordance with UK Building Regulations Approved Docu-
ment J, to a distance of 300 mm in front of the stove and 150 mm to each side measuring
from the door of the combustion chamber.
The clearance distances to combustible material beneath, surrounding or upon the hearth
and walls adjacent to the hearth should comply with the guidance on the separation of
combustible material given in UK Building Regulations Approved Document J and also in
these stove instructions.
For the Installer
Finally before firing the stove for the first time a check should be made to ensure that the
assembly and stove installation has been satisfactory and that there are no leaks in any
seals in the appliance and appliance connections to the chimney.
Ensure that the appliance and chimney flue are functioning correctly before finally hand-
ing over to the user. If necessary read the later parts of this manual for guidance on care
required when first lighting.
Inform the user that the appliance has been commissioned and ready to use and give
instruction on the safe operation of the stove.
These Instructions must be left with the user and the user should be instructed to keep
them in a safe place.

ENGLISH RAIS - manual for RAIS 700
20
Operating instructions
Please note that HETAS Ltd Appliance Approval only covers the use of dry sea-
soned wood logs on this appliance. HETAS Ltd Approval does not cover the use
of other fuels either alone or mixed with the wood logs, nor does it cover instruc-
tions for the use of other fuels.
Fuel
The stove is designed and approved in accordance with EN 13240 and NS 3058 for stok-
ing split, dried firewood. The firewood must have a water content of 15-22% and its max.
length should be the length of the combustion chamber minus 50-60 mm.
Stoking with wet firewood causes both soot, environmental pollution and bad fuel
economy. Freshly cut wood contains approx. 50-70% water and is thoroughly unsuitable
for stoking. Count min. 1 year of storage time for newly cut wood before using.
Wood with a diameter of more than 100 mm should be split. Regardless of wood size, it
should always have at least one surface area free of bark.
We do not recommend stoking with painted, laminated or impregnated wood, wood with
a synthetic surface, painted refuse wood, chipboard, plywood, domestic waste, paper bri-
quettes and pit coal, as this will produce malodorous smoke, which could be poisonous.
When firing with the above-mentioned items and amounts larger than those recommend-
ed, the stove is subjected to a larger amount of heat, which results in a higher chimney
temperature and lower efficiency. This can result in the stove and chimney becoming dam-
aged and would void the warranty.
The calorific value of the firewood is closely connected to the moisture level of the
firewood. Moist firewood has a low heat value. The more water the wood contains, the
more energy it takes for this water to vaporise, resulting in this energy being lost.
ONLY USE RECOMMENDED FUELS
The following table shows the calorific value of different types of wood, which have been
stored for 2 years, and which have a residual moisture of 15-17%.
Wood Kg dry wood pr. m3 compared to beech/oak
Hornbeam 640 110%
Beech and oak 580 100%
Ash 570 98%
Maple 540 93%
Birch 510 88%
Mountain pine 480 83%
Fir 390 67%
Poplar 380 65%
1 kg of wood yields the same heat energy irrespective of wood type. 1 kg beech merely
takes up less space than 1 kg of fir.