Ranger design 76-U1236 User manual

INSTALLATION GUIDE
76-U1236, 76-U1248 & 76-U1260
( ALUMINUM )
https://rangerdesign.com/products/
oor-retainer-lip-for-shelving-units-
60-long-76-u1260/

For technical support, contact us at 1-800-565-5321 76-U12XX Installation Guide |REV. A | Page 2
QUICK START GUIDE
REQUIRED ITEMS
1 PERSON
1.1 Setup............................................................................................................................................... 3
Phase 1 - Assembly
Phase 2 - Installation
4
2.1 Regular Install.................................................................................................................................
Cordless Impact
Tape Measure
3/8" Socket
7/16” Socket
Hex Key 5/16”
Drill
Drill Stop Collar
Drill Bit 7/16”
Wrench 1/2”
SAFETY INSTRUCTIONS
WARNING
•Before the installation, carefully read the supplied installation guide to avoid possible injuries and dam-
ages resulting from incorrect installation. Always keep the installation guide in an accessible location at
all times for reference during installation.
•Installers must always wear appropriate safety gear during installation. This may include but is not limit-
ed to gloves, steel toed shoes, and safety glasses.
CAUTION
•Follow all vehicle manufacturer instructions before attempting any installation.
•To prevent rust and other damages, do not drill into the factory floor panels.
•Before drilling for the tapping inserts, use a drill stop collar to prevent accidental drilling the van met-
al floor panel which may result in damage to components underneath, such as wiring harnesses, fuel
tanks and battery modules.

For technical support, contact us at 1-800-565-5321 76-U12XX Installation Guide |REV. A | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Unpack components; compare with the bill of materials.
1.1.2 Verify all parts are present.
Item No. Description Qty.
70-027 or
70-028 or
70-029
Retainer Lip 36”
Retainer Lip 48”
Retainer Lip 60”
1
96-1200 Install Fastener Kit 1
BILL OF MATERIALS
96 - 1200 Fastener Kit Fastener Assembly
1.1.3 Fastener kits.
3×
3× # 92-102 Screw HWH tpAB #14x1”
# 94-112 Serrated Flange Nut 1/4"-20
1×
1×
70-02X
1×
1× # 90-110 Bolt hx-hd gr5 1/4”-20x3/4”
1×
1× # 98-112 Flat washer USS 1/4” O.D. 3/4”
3×
3×
1×
1×
Item No. Use with shelf width
76-U1236 36”, 72”, 84”
76-U1248 48”, 84” 96”
76-U1260 60”
UNIT OPTIONS
#90-110 Hex Bolt
#98-112 Flat Washer
#94-112 Serrated Nut
# 92-102 Self tap

For technical support, contact us at 1-800-565-5321 76-U12XX Installation Guide |REV. A | Page 4
PHASE 2 – INSTALL
2.1 REGULAR INSTALL
2.1.1 • Place the retainer lip on the inside of the end
2.1.2B • Install the retainer lip to any other oor.
#92-102 Screw HWH tpAB #14x1”
TOOLS
Cordless Impact
3/8” Socket
HARDWARE USED
3×
View from rear of shelving
End Panel Retainer Lip
“You have successfully installed your Retainer Lip.
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: [email protected]om
2.1.3 • For 72”, 84” and 96” shelving, align and bolt retainer lip to center bar.
TOOLS
Cordless Impact
7/16” Socket
HARDWARE USED
1X
#94-112 Bolt 1/4”-20x3/4” ZINC
#98-112 Nut 1/4”-20 ZINC
#90-110 Washer 1/4” O.D. 3/4” ZINC
2.1.2A • Install the retainer lip to the Ranger E-Floor. Use hardware provided with the
oor. See oor install guide for details.
#90-204 Hex Bolt
5/16" × 3/4"
#99-114 Wood Inserts
5/16”x13mm
Floor
NOTE: Use 5/16” washers and
lock-washers. (Not included)
TOOLS
Hex Key 5/16”
Drill
Drill Stop Collar
Drill Bit 7/16”
Wrench 1/2”
HARDWARE USED
3×
WITH E-FLOOR
WITHOUT E-FLOOR
OPTIONAL