Ranger design 3320-PC User manual

INSTALLATION GUIDE
3320-PC CONTOURED PARTITION
Promaster City ( Clear Plastic )

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 2
QUICK START GUIDE
REQUIRED ITEMS
2
PERSONS
qCordless Impact
qCordless Drill
qKnife
qPhilips Screw Driver
qPlusnut Tool
qRatchet
q1/2" Socket
q7/16" Socket
q10mm Socket
q13mm Socket
qT30 Torque Bit
qT40 Torque Bit
q9/16" Wrench
q1" Holesaw
q1.1 Setup....................................................................................................................................................
q1.1.1 Unpack components; compare with the bill of materials................................................................
q1.1.2 Verify all parts are present...............................................................................................................
q1.1.3 Identify the assembly and installation fastener bags......................................................................
q1.2 Partition Assembly................................................................................................................................
q1.2.1 Attach the lower panel and mounting track to the upper panel......................................................
q1.2.2 Attach the sides of the upper panel and lower panel together on both sides................................
3
3
3
4
5
5
6
Phase 1 - Assembly
q2.1 Tips on how to attach a plusnut..........................................................................................................
q2.1.1 Attach plusnut using plusnut gun...................................................................................................
q2.1.2 Attach plusnut using Ranger plusnut tool......................................................................................
q2.2 Vehicle preparation..............................................................................................................................
q2.2.1 Removing handle............................................................................................................................
q2.2.2 Removing overhead plastic............................................................................................................
q2.2.3 Driver and passenger sides preparation.........................................................................................
q2.2.4 Ceiling and oor preparation..........................................................................................................
q2.3 Contoured partition installation...........................................................................................................
q2.3.1 Attach J - shapes and the oor brackets in the van.......................................................................
q2.3.2 Lift the assembled partition in the van, then bolt both sides of the partition in the van.................
q2.3.3 Attach the upper and lower panels to the J - shapes and oor brackets.......................................
q2.3.4 Apply the warning label on the upper panel...................................................................................
7
7
7
8
8
9
10
11
12
12
13
14
15
Phase 2 - Installation

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 3
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.2 Verify all parts are present.
Item No. Description Qty.
30-089 Floor Bracket 1
30-090 J - Shape Bracket 2
30-092 Lower Panel 1
70-633 Mounting Track ( 53-1/4" L ) 1
79-932 Warning Label ( Bilingual ) 1
30-0860 Upper Panel w/ Label 1
94-3002 Assembly Fastener Bag 1
96-3002 Installation Fastener Bag 1
1.1.1 Unpack components; compare with the bill of materials.
30-089
30-0860
70-633
30-090
30-092

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 4
1.1.3 Identify the Assembly and Installation fastener bags.
Assembly Fastener Bag Hardware Assembly
Hardware AssemblyInstallation Fastener Bag
#94-112 Serrated Nut
9×9×
#90-114 Hex Bolt 1/4" × 1"
#98-112 Flat Washer
7×7×
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
4×4×
#90-110 Hex Bolt 1/4" × 3/4"
#98-118 Lock Washer
#98-112 Flat Washer
Serrated Nut
5/16"-18
ZINC
# 94-116
7×7×
13×13× # 98-112
Flat Washer
1/4", 3/4" OD
ZINC
Serrated Nut
1/4"-20
ZINC
# 94-112
9×9×
Flat Washer
5/16", 7/8" OD
ZINC
# 98-116
7×7×
# 98-118
Lock Washer
Regular 1/4"
ZINC
4×4×
Hex Bolt
5/16"-18 × 3/4"
GR-5 ZINC
# 90-204
7×7×
Hex Bolt
1/4"-20 × 1"
GR-5 ZINC
# 90-114
9×9×
Hex Bolt
1/4"-20 × 3/4"
GR-5 ZINC
# 90-110
4×4×
12×12× # 98-112
Flat Washer
1/4", 3/4" OD
ZINC
Flat Washer
5/16", 7/8" OD
ZINC
# 98-1168×8×
# 98-118
Lock Washer
Regular 1/4"
ZINC
12×12×
Hex Bolt
1/4"-20 × 1-1/4"
GR-5 ZINC
# 90-1184×4×
Spacer
0.375" ID, × 1.0" OD × 0.25" L
NYLON
# 98-15724×24×
# 98-122
Lock Washer
Regular 5/16"
ZINC
8×8×
# 90-6688×8× Hex Bolt M8-1.25 × 40 CL 8.8 DIN
933 BLACK OXIDE
# 94-130 Plusnut .2504×4×
8×8× Hex Bolt M6-1.0 × 40 CL 12.9 DIN
933 BLACK OXIDE
# 90-836
# 98-158
Retaining Washer
M16 ( 1/4")
NYLON
8×8×
#90-668 Hex Bolt M8 × 40
#98-122 Lock Washer
#98-116 Flat Washer
8×8×
#90-118 Hex Bolt 1/4" × 1-1/4"
#98-118 Lock Washer
#98-112 Flat Washer
#94-130 Plusnut .250
4×4×
#90-836 Hex Bolt M6 " × 40
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Spacers ( 3 )
#98-158 Retaining Washer
8×8×

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 5
1.1.4 To clear the airbag brackets, cut both sides of the top edges, as shown.
PHASE 1 – FOR PROMASTER CITY 2021+ ONLY

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 6
PHASE 1 – ASSEMBLY
1.2 PARTITION ASSEMBLY
1.2.1 Attach the lower panel and mounting track to the upper panel.
#90-114 Hex Bolt 1/4" × 1"
#98-112 Flat Washer
#94-112 Serrated Nut
HARDWARE USED
7×
TOOLS
qCordless Impact
q7/16" Socket

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 7
1.2.2 Attach the sides of the upper panel and lower panel together on both sides.
#90-114 Hex Bolt 1/4" × 1"
#98-112 Flat Washer
#94-112 Serrated Nut
HARDWARE USED
2×
TOOLS
qCordless Impact
q7/16" Socket

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 8
PHASE 2 – INSTALLATION
2.1 TIPS ON HOW TO ATTACH A PLUSNUT
FORWARD REVERSE
TIPS: Put the plusnut on the plusnut gun, then attach the plusnut in the hole by turning the gun forward until the
plusnut locks, then remove the gun by turning in reverse.
2.1.1 Attach the plusnut using the plusnut gun.
2.1.2 Attach the plusnut using the 6490 plusnut tool.
6490 HARDWARE USED
Flat washer 1/4"
Flat washer 1/4" BS × 3/4" OD
TOOLS
qCordless Impact
q7/16" Socket
q9/16" Wrench
TIPS STEP 1:
Assemble the 6490 plusnut tool with the hardware needed,
plusnut and the 9/16" wrench as shown.
FORWARD REVERSE
TIPS STEP 2:
Attach the plusnut in the hole by turning
the bolt forward using an impact with a
7/16" socket until the plusnut locks, then
remove the bolt by turning the impact in
reverse.
NOTE: The hardware used for the 6490 plusnut tool is not included in the fastener bag.
The 6490 plusnut tool can be ordered separately upon demand at no charge.

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 9
NOTE: If you are installing a Composite Partition and your Promaster City is supplied with an oversized sliding
door handle, this handle must be removed in order for the door to close properly.
NOTE: Pulling the cable unlocked the
door.
PHASE 2 – INSTALLATION
2.2 VEHICLE PREPARATION
2.2.1 Removing handle.
Detach the plastic bracket on the cable from
the metal part of the handle, then slide the ca-
ble across the channel and pop out.
Tape or roll the cable.
TOOLS
qCordless Impact or Ratchet
qPhilips Screw Driver
qT30 Torque Bit
Separate the two halves of the handle exposing the
two bolts at the top by removing the small philips
screws and the bolt at the bottom.

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 10
NOTE: There are two types of covers.
( White Covers - Without OEM partition, and Black Covers - With OEM partition )
2.2.2 Removing overhead plastic.
NOTE: Do these on both sides of the
For the white cover, remove the two
screws on the side and bolt on the front.
TOOLS
qCordless Impact or Ratchet
qPhilips Screw Driver
q7/16" Socket
NOTE: Do these on both sides of the
For the black cover, remove the screw on
the side and bolt on the front.
TOOLS
qCordless Impact or Ratchet
qPhilips Screw Driver
q7/16" Socket

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 11
2.2.3 Driver and passenger sides preparation.
Pull back the plastic cover, then cut a 1"
square from the plastic cover to uncover
the threaded holes or drill the plastic cover
using 1" holesaw.
TOOLS
qCordless Drill
qKnife
q1" Holesaw

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 12
TOOLS
qPlusnut Tool
# 94-130
Plusnut .250
HARDWARE USED
4×
NOTE: Enlarge these holes if the plusnuts don't t, using 3/8" drill bit or step drill.
2.2.4 Ceiling and oor preparation.
Attach plusnut on these 4 holes.
Remove plastic caps and the two D-rings from vehicle oor, then veri-
fy if the threads are in good condition.
TOOLS
qCordless Impact
qT40 Torque Bit

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 13
2.3.1 Attach J - shapes and the oor brackets in the van.
#94-112 Serrated Nut
#90-118 Hex Bolt 1/4" × 1-1/4"
#98-112 Flat Washer
HARDWARE USED
4×
TOOLS
qCordless Impact
q7/16" Socket
HARDWARE USED
8×
TOOLS
qCordless Impact
q13mm Socket
#90-668 Hex Bolt M8 × 40
#98-122 Lock Washer
#98-116 Flat Washer
PHASE 2 – INSTALLATION
2.3 CONTOURED PARTITION INSTALLATION

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 14
TOOLS
qCordless Impact
q10mm Socket
2.3.2 Lift the assembled partition in the van, then bolt both sides of the partition in the van.
HARDWARE USED
8×
#90-836 Hex Bolt M6 " × 40
#98-118 Lock Washer
#98-112 Flat Washer
#98-157 Spacers ( 3 )
#98-158 Retaining Washer

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 15
TOOLS
qCordless Impact
q1/2" Socket
HARDWARE USED
7×
#90-204 Hex Bolt 5/16" × 3/4"
#98-116 Flat Washer
#94-116 Serrated Nut
TOOLS
qCordless Impact
q7/16" Socket
HARDWARE USED
4×
#90-110 Hex Bolt 1/4" × 3/4"
#98-118 Lock Washer
#98-112 Flat Washer
2.3.3 Attach the upper and lower panels to the J - shapes and oor brackets.

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 16
NOTE: Put the warning label in a place
where it’s easy to see.
2.3.4 Apply the warning label on the upper panel.

For technical support, contact us at 1-800-565-5321 3320-PC Installation Guide |REV. J2 | Page 17
“Congratulations, you have successfully installed your
Contoured Partition!
Thank you for doing business with us.”
For any feedback or suggestions you may have, please contact: [e-mail]